Bike Frame Structural Analysis with FEM

  Рет қаралды 38,728

SimScale

SimScale

Күн бұрын

Пікірлер: 16
@Prabh_Dhillon1993
@Prabh_Dhillon1993 3 жыл бұрын
Can you pls explain what are boundary conditions for braking and irregularities?
@tomruediger8559
@tomruediger8559 7 ай бұрын
In ISO4210 the horizontal front load is described with a mass that is falling from a specific height on the front axle of the bicycle but not as a force. How did you come up with the 2x1000N of force acting on the axle?
@vanishrilalsangi1559
@vanishrilalsangi1559 2 жыл бұрын
if I have two valid results after running fea analysis where both do not cross the yield strength then how to choose the right answer and why to chose that particular answer
@黃冠傑-v3t
@黃冠傑-v3t 2 ай бұрын
Nice performance, very detail.
@aminegc9353
@aminegc9353 2 жыл бұрын
Is there any standards or codes to design and concept the bikes according to that codes? standards dimensions and all details please ????
@jacopobilotto9221
@jacopobilotto9221 4 жыл бұрын
If I put two cilindrical constraints at the rear of the chain stay and a vertical support on the front tube, and apply a vertical downward force at the sit, should I expect the front tube to displace away from the sit or to come closer? My geometry is very similar to yours, a classical safety diamond shaped frame
@evotechcaeltd1583
@evotechcaeltd1583 4 жыл бұрын
Is it possible to consider 1) a composite frame, with a discrete ply/laminate definition (based on classical laminate theory), and 2) transient impact analysis based on an initial velocity (such as the ISO4210 physical test definition)?
@aadityadagadkar2772
@aadityadagadkar2772 4 жыл бұрын
Very nice
@ddfSDGFdfsgsFDG
@ddfSDGFdfsgsFDG 4 жыл бұрын
Why do you use a 3d mesh instead of a 2d with less elements?
@JousefM
@JousefM 4 жыл бұрын
You could but we only offer 3D elements at the moment. We already saved some time by using half the model though as you have seen :)
@ramachandransankar750
@ramachandransankar750 4 жыл бұрын
Braking what is the load calculated
@JousefM
@JousefM 4 жыл бұрын
You can find all the details here: www.simscale.com/projects/kcontractor/bikeframe_homework_1/
@nobody617
@nobody617 2 жыл бұрын
Playback speed 1.75. works good
@jonienglish3231
@jonienglish3231 2 жыл бұрын
@26.29 with the lower position Seat stay - you can see more stress in the Seat tube compared to traditional design high mounted seat stay connected at seal collar . i think the newer Design is Retarded and just MARKETING BS to sell more bikes to the MINIONS !!!!!!!!!!! No Added Beneft + a HARSHER RIDE !!!!!!!!!!! Since the SEAT STAYS are SHORTER
How to Use CFD to Simulate Airflow in Hospitals
51:00
SimScale
Рет қаралды 3,7 М.
Bicycle Frame with Beam Elements ANSYS Workbench
21:07
Learn Finite Element Analysis
Рет қаралды 16 М.
UFC 310 : Рахмонов VS Мачадо Гэрри
05:00
Setanta Sports UFC
Рет қаралды 1,2 МЛН
99.9% IMPOSSIBLE
00:24
STORROR
Рет қаралды 27 МЛН
We Attempted The Impossible 😱
00:54
Topper Guild
Рет қаралды 40 МЛН
Weekend Special: FEM in FreeCAD for Dummies
16:03
Katt Kushol
Рет қаралды 6 М.
What Goes Into Designing a Carbon Bike Frame?
8:32
The Middle Mouse
Рет қаралды 11 М.
Understanding the Finite Element Method
18:36
The Efficient Engineer
Рет қаралды 1,8 МЛН
Topology optimized bicycle frame - Design and Fabrication
6:44
ideas2cycles
Рет қаралды 10 М.
Introduction to Simulations (FEA)
20:54
SolidWorks With Aryan Fallahi
Рет қаралды 50 М.
How To Make A Steel Road Bike Frame From Scratch.
23:17
David Arthur - Just Ride Bikes
Рет қаралды 109 М.
How Are Carbon Fibre Bikes Made? | LOOK Cycle Factory Tour
20:21
Global Cycling Network
Рет қаралды 3,9 МЛН
How to fillet braze - From start to finish with Paul Brodie
38:44
paul brodie
Рет қаралды 456 М.
Structural Shapes Ranked and Reviewed - Which one Wins?
15:34
The Engineering Hub
Рет қаралды 715 М.
Everything about motorcycle frames   | Motorcycle breakdown |
11:44
UFC 310 : Рахмонов VS Мачадо Гэрри
05:00
Setanta Sports UFC
Рет қаралды 1,2 МЛН