Single Phase Motor Reverse Forward Connection || Motor Connection

[@robertgregory8964]

Most clear & informative explanation I have ever seen.

[@spoonophosese2450]

Agree very good explanation

[@TheSamEmpire254]

Great explanation

[@MrPawipawi]

Thanks. Simple and clear.

[@ishaaqchihuri2917]

You explain very well .keep it up

[@collinsmwila5721]

very good explanation

[@yusufishaq4565]

Thanks, you helped me a lot with this information

[@mextonwom8681]

Very best explanation

[@yvenkataramana7871]

Very good explain sir❤

[@wajidyoutuber4555]

Very good information technology systems Thanks for share it ❤

[@Cesar-be8xb]

thank you for all the information, how do size the capacitor for the single phase motor

[@vasu615]

Good explanation

[@myeltroelectropowertechnol9838]

Very Good Information..... Thank You For All The Tnformation

[@abuhamzahalmasry5627]

thank you brother.very simple and informative

[@joezie2609]

Thank U Sir🙏🙏🙏

[@sambathbunkh]

Great video

[@technicalraja-ld2mp]

Super sir ji 😊

[@tapanmaity6779]

Very clear explanation thank you

[@MAYURGUPTA9]

Nicely explained

[@kabandajamir9844]

So nice thanks

[@ssennonojohnmary4406]

Great, thanks.

[@SureshBRane]

Very Nice, Thank you.

[@ejioforprecious6108]

Thank you very much ❤ How do I measure the resistance of the wires?

[@engkuskuswendi6106]

Can it be wired using a contactor and push button?

[@JohnMwafulirwa]

Just watched this four times. And all is very clear. You can be asking me questions 😂😂😂.

[@samiarti]

I didn’t understand any of it, except that I did understand 1) how to identify the running winding wires, and 2) that I need to swap those two over. And motor is running the way I need it now thanks…

[@samarsekharreddy]

Take Multi meter and measure resistance which is having higher resistance value that is running winding and low resistance value is starting winding in video he has given wrong connection is correct

[@johnanddiann100]

@@samarsekharreddyNo, the starter winding is thinner wire and has higher resistance. The running winding uses thicker wire which has lower resistance.

[@alexgitau5]

Nice one

[@zela5814]

my motor has 4 wires. 2 for line input +/- and other two for capacitor. When I changed the supply +/- position at reverse, no rotation changed.

[@RamteaPachuau-ix1lu]

6 Wire,red wire 2,yello 2,green wire2..how to connect😊

[@fourkings7897]

Wire paruk a nih chuan three phase a ni ang, three phase wirings tiin zawng rawh

[@joymathew1952]

Usually we change the terminals of starting winding for the reversal of the 1Ph motors. More over you didn't explained how to change the rotation if there are only 3 wires came out of the motor..ie : Common Running Starting

[@narayanpsd.dhakal7267]

How can i create this type of digram with video for short cliip..

[@joezie2609]

😮😮😮😂😂😂❤❤❤

[@RamteaPachuau-ix1lu]

Please help..v¹ and v²

[@temp26j724-i]

Sir, isnt that the lowest Resistance is of the Starting Coil? The higher Resistance one is of the Running coil? In the video you mention it in the other way round...🤔

[@KhalEd-ur4yh]

No. he is correct The higher resistance is for starting coil

[@temp26j724-i]

@KhalEd-ur4yh okay, im confused too

[@johnanddiann100]

The starting coil uses thinner wire which has higher resistance.

[@temp26j724-i]

@@johnanddiann100 Okay, got it. But Im confused there are service tech saying that some 'smaller motors', where the Running/Main Coil is alrdy winded using Small sized winding wires; then the Starting Coil won't be winded with Thinner winding wires anymore. Because the design of its motor Windings Ratio of Main(running) to Aux(starting) Windings will make the windings at the Start Coil SHORTER, so the end measured result for this kind of Motor typically will result the Aux(Start) Coil having Lower resistance relative to the Main(running) coil. Im confused & need clarification for this🙏

[@oldgamer1330]

My single phase motor only has 3 wires.