single stage CE amplifier on breadboard

[@princesaini1452]

expt: construction of single stage transistor amplifier circuit and measurement of voltage, gain, and output impedance, how to measure these sir can tell ?

[@MindsRiot]

For measuring voltage refer this video kzbin.info/www/bejne/inayk3xmm91kl5o After measurements you can calculate gain (output/input)

[@princesaini1452]

@@MindsRiot how about output impedence measuremt?

[@dhiyaguvasandh3516]

How to determine the components values to design the single stage ce amplifier? Sir

[@MindsRiot]

Already given in lab manual, or you can try simulation with different values

[@abhijithanilkumar4959]

Some clipping has occured in negative cycle right

[@MindsRiot]

Hmm...its due to DC offset control on FG

[@adityanarayan5946]

Why output wave form clipped when we give sine wave as input signal. how to remove output sine wave clipping and why it's happening.please reply

[@MindsRiot]

Keep frequency less to avoid chopped output (looks like square wave)

[@MindsRiot]

What is your input frequency?

[@adityanarayan5946]

@@MindsRiot sine wave as input but output is clipped like in video

[@MindsRiot]

Frequency?

[@adityanarayan5946]

1000 hz

[@prachipatil3552]

Two stage CE amplifier on PCB

[@prachipatil3552]

Build two stage CE amplifier on PCB kaise kare

[@prachipatil3552]

Components kon konte ahe

[@MindsRiot]

First try on breadboard. 2 Transistors, 8 resistors, 5 capacitors, breadboard, connecting wires. Vales of components are given in video or check in lab manual

[@prachipatil3552]

Thanks sir

[@jayeshvarunkar6982]

Asmr vala feel aa gya bhai Mai to so gya dekhte dekhte😂😂

[@dhirajpatil9324]

What we conclude in this practical

[@MindsRiot]

Hence we can conclude that, single stage CE amplifiers can amplify input signal and output signal is 180 degree out of phase

[@vijaykv4675]

Respected Sir, Could you tell me why the output wave is clipped pls reply sir And how can we avoid this problem 🙏

[@MindsRiot]

If input frequency is high, we get clipped (like square wave) waveform at output. Keep input frequency less to get proper output. Let me know the result after doing

[@vijaykv4675]

@@MindsRiot Thankyou so much sir , is this suitable for BSc Physics final year project?

[@MindsRiot]

Can't say, it's upto related teacher

[@vijaykv4675]

@@MindsRiot Ok Sir. I shall update after talking to my teacher 😊

[@anseesurrehman5033]

Assalam o alaikum sir.. Kindly yea bta dain k series main ce ur re kaisy lgy gain...

[@MindsRiot]

Emitter capacitor CE and Emitter resistor RE are connected in parallel, not in series. Thanks for asking question

[@anseesurrehman5033]

G sir...... Agr series main kagny hun the then kaisy lgy gain

[@randomfacts4663]

Hello sir Haam rasistor aur capacitor ki value kaise decide karenge🤔

[@shafiquesayed2673]

How to know the value of capacitor to be used in circuit, like you use 0.1uF for Cin and Cc why?

[@MindsRiot]

By considering value of ripple to reduce

[@shafiquesayed2673]

@@MindsRiot can you make video on it please.

[@MindsRiot]

Yes sure, need some time.

[@shafiquesayed2673]

@@MindsRiot thank you so much

[@artishukla1930]

Sir please aap electronics ke video dalo

[@MindsRiot]

Ok, please suggest topic you want

[@varadbhadgaonkar]

Ok

[@dhirajpatil9324]

Which type of biasing we used in this practical/ ckt

[@MindsRiot]

Voltage divider biasing is used. Voltage divider biasing can be formed by using resistors R1 and R2.

[@khushimuhammadkhan4911]

sir inputs per kitna volts Ac dna h ?.kindly help!......

[@MindsRiot]

For input, function generator is used with 100hz to 10khz and few millivolts Vpp. For transistor biasing, 5v or 12v DC is used. You can watch following video in which I simulated the same circuit on Multisim software, I hope it works for you kzbin.info/www/bejne/rp3Np4CgjpejaKs

[@khushimuhammadkhan4911]

Thanks sir .❤...sir agar ham 5v Ac with 50Hz Da to circuit kam kara gya .?..

[@MindsRiot]

@@khushimuhammadkhan4911 5v AC as input signal is not recommended. First start from 10mv and then increase voltage step by step. Before going to test on breadboard, please simulate the circuit on simulation software, it will give you rough idea

[@khushimuhammadkhan4911]

Thanks sir .❤

[@shubhamkadam2741]

Shubham kadam

[@dhirajpatil9324]

Interpretation of result is ..........

[@MindsRiot]

Same as conclusion

[@nicuvaleriumalcota5520]

Bad amplificaton