SIP Validation ​⁠

  Рет қаралды 3,973

PHARMAVEN

PHARMAVEN

Күн бұрын

Пікірлер: 19
@mahmmodali2516
@mahmmodali2516 7 ай бұрын
Very informative sir
@Monit_Panwar
@Monit_Panwar 6 ай бұрын
Legend ❤❤❤
@deepakjaiswal3988
@deepakjaiswal3988 7 ай бұрын
Nice sir
@yogeshkoli851
@yogeshkoli851 2 ай бұрын
Sir filter integrity ke bare me video banayiye na plz
@Vikayadavbpharmhhhh
@Vikayadavbpharmhhhh 7 ай бұрын
Difference between lag time and equilibrium time
@ravaljinang8389
@ravaljinang8389 7 ай бұрын
Diff. Btwn lag time and equlabrium time
@sumantakumarjena484
@sumantakumarjena484 5 ай бұрын
Sir,Sip ka Impact/Risk assessment ka video.
@rakeshbariya-v7z
@rakeshbariya-v7z Ай бұрын
mfg CPP ka video bhejo
@domendrasahu4058
@domendrasahu4058 2 ай бұрын
Sir psg ka pressure kitna rhna chahiye
@mayankdhiroliya
@mayankdhiroliya 7 ай бұрын
Sir, Gas filter or J tube ka kya use hota hai storage vessel me
@PHARMAVEN
@PHARMAVEN 7 ай бұрын
Gas filter for filtering gas when solution level comes down J tube is to transfer solution from mixing vessel to filtration vessel
@namratajain415
@namratajain415 2 ай бұрын
During operation When temperature drop on 121 so in case sip cycle valid or not
@PHARMAVEN
@PHARMAVEN 2 ай бұрын
It cannot be considered as valid but need more information to understand that at what time it drop, for how many seconds or minutes, what was total time of sterilization and at what location it went low and at how many locations it went low
@Rakesh-wj9vn
@Rakesh-wj9vn 6 ай бұрын
Sir in vessel line there is formation of condensed due to which temperature not reaching 121 so why this condenset is forming in lines what is the reason?
@PHARMAVEN
@PHARMAVEN 6 ай бұрын
I will make video on this Can you share vessel size , steam trap is there or not, vessel line diameter, length of line, how sensor is placed? Give as much of information available with you as you can
@Rakesh-wj9vn
@Rakesh-wj9vn 5 ай бұрын
500L vessel yes steam trap is there off inch diameter sensor is placed horizontal to the line Line length is not sure may be 3/4 feets
@mohitbisht2041
@mohitbisht2041 4 ай бұрын
Sir what is the leak rate value in sip ... In our company the acceptance limit 0.20 bar that is higher then autoclave why ??
@PHARMAVEN
@PHARMAVEN 4 ай бұрын
In SIP, usual practice is to set 1 bar pressure and 0.1 bar reduction is allowed after 30 minutes of hold. Unlike autoclave, in SIP, pressure is maintained after SIP throughout before filtration is started hence there is no ingress of non-sterile air in vessel.
@mohitbisht2041
@mohitbisht2041 4 ай бұрын
Thank you sir
小丑教训坏蛋 #小丑 #天使 #shorts
00:49
好人小丑
Рет қаралды 16 МЛН
Как Я Брата ОБМАНУЛ (смешное видео, прикол, юмор, поржать)
00:59
How many people are in the changing room? #devil #lilith #funny #shorts
00:39
Quando A Diferença De Altura É Muito Grande 😲😂
00:12
Mari Maria
Рет қаралды 35 МЛН
Aseptic Practices, Media Fill and Sterility Assurance
14:40
Hitendrakumar Shah
Рет қаралды 27 М.
小丑教训坏蛋 #小丑 #天使 #shorts
00:49
好人小丑
Рет қаралды 16 МЛН