Few tips, make sure the pipes are super clean, when soldering any fitting start on the easiest joint first as the heat will travel tovthe harder to reach joint, dont over heat, if the flame turns green you have over heated the joint and it will leak ive been a plumber for 45 years and trust me follow these simple rules and you will be an expert in no time
@garywateridge6 ай бұрын
Thankyou,I am learning and a maintenance person have, i found a low heat,taking time to slowly heat joint doesnt burn off flux quickly and dabbling solder from other side of fitting works well,flows well every time
@williamgrissom90225 ай бұрын
Probably harder with today's silver solder since it has a higher melting point. My shiny copper tubing starts getting dark before reaching the solder melting point. Perhaps it is the flux degrading. I keep the heat mostly on the fitting, not the tubing.
@dantheman1337Ай бұрын
@@williamgrissom9022 Heat the tube a little it you find this happening. I find it helps
@DudjrkfjjffjkffuАй бұрын
The color of the flame doesn’t have anything to do with how hot the joint is. I don’t quite have 45 years in the trade but I have spent my fair share of time with copper. I have a leak here and there but I’ve soldered many thousands of joints. I agree though, you should always clean your pipe and joint properly.
@matthewhauserman475516 күн бұрын
@@Dudjrkfjjffjkffu green flames usually indicate burning copper. It's a chemical reaction with the light copper emits when it's atoms are moving rapidly. It's the same reason copper turns green from oxidizing.
@mondavou9408 Жыл бұрын
I love you showed "how to" and "how not to" and showed what it looks like. You can learn quite a bit by both. Thank you.
@allahdittababu48022 жыл бұрын
Honestly seen a lot of soldering videos but for the first time I understand flux .... excellent video
@mikenco Жыл бұрын
Love that tip about bending the solder into portions.
@stevejones90448 ай бұрын
Exactly. I'm not new to soldering as DIYer but never knew how much solder to use so I naturally put too much "just to be sure". 😂
@PeteCswampy Жыл бұрын
Rodger is such a great teacher.
@221b-Maker-Street Жыл бұрын
Roger is an excellent presenter - just the right blend of knowledgeable, skilled, and engaging. As a jeweller, I'm new to this specific kind of soldering, so I feel lucky to have stumbled upon your video before wading through a lot of other inferior content on KZbin - thank you!
@SkillBuilder Жыл бұрын
Wow, thank you!
@paulbrenning2310 Жыл бұрын
What an absolute masterclass. As usual.
@allmanjason292 жыл бұрын
Tempted to give this a thumbs up before I've even seen the end as Roger is a great tradesman and I know this will be a great video. Really enjoy the channel mate
@daves40262 жыл бұрын
I did
@d.whaire469 Жыл бұрын
Great video, thank you Sir. My house was build in 1945 and I am doing a bathroom reno myself. Your video will surly help this first time solderer :) Thank you!!
@SkillBuilder Жыл бұрын
Glad it was helpful!
@johnparkhurst82510 ай бұрын
I'm just a DIY 'er . Some where along the line I picked up working your way UP as you solder. The theory being, heat rises. Probably nothing to it.
@Cliff69652 жыл бұрын
Someone like me has to watch this over and over before I try it. lol Hello, good teacher, Skill Builder.
@JohnSmith-ws7fq Жыл бұрын
Thanks!
@SkillBuilder Жыл бұрын
Thank you John that is very good of you.
@damionlee76582 жыл бұрын
This came about just at the right time for me. Replacing an outside tap very soon and the new tap I bought has a Yorkshire fitting. I was going to look up a tutorial because, whilst it seemed obvious how to use it, I'm always keen to sanity check (especially as my soldering experience is all with electrics). You've saved me a search, and also stopped me from unnecessarily buying a specific soldering torch for pipework, as I now realise the gas torch I have will do the job 👍 Cheers. 👍
@jimbarclay83707 ай бұрын
Great footage on how it all works. And lots of important tips that I had not seen on other videos, like not overdoing it on the flux and making sure things are dry,
@paullefur62132 жыл бұрын
Thanks Roger this vlog you did in plain english if you get me, simple and well explained great job
@Tony-dk1bp Жыл бұрын
This guy is very likable and easy to follow. Thanks
@davidpatterson15742 жыл бұрын
Thanks Rodger--another great video-I’m a retired Spark, but have soldered a few pipes in my time--I would concur with you, regarding cleaning the flux from the pipes--absolutely vital--I live on a private estate here in Northern Ireland, and quite a few of of the houses have has leaks in the original copper pipes, and the general consensus is that it was down to the plumber not cleaning the flux from the pipes--
@SkillBuilder2 жыл бұрын
Thanks for sharing
@Neil_down_south2 жыл бұрын
Is it a case of using abrasive to remove the flux? Any other methods?
@erniemenard77272 жыл бұрын
@@Neil_down_south Flux is an acid, so wiping it off with a rag well dampened with something like Windex will neutralize it.
@jackmclane1826 Жыл бұрын
It might depend on what flux exactly you are using. Also not deburring is said to cause leaks close to the joints not exactly at the joints, but close.
@williamgrissom90225 ай бұрын
Clever tip about zig-zagging the solder as a rough measurement. I've seen those pre-soldered fittings at the store but assumed they were a new type of push-seal like Sharkbite We love listening to old-school British tradesmen who have a very professional attitude.
@jimdavis52302 жыл бұрын
Regarding not using a naked flame in some places, I've used a paint stripping electric heat gun to solder Yorkshire fittings on 15mm pipes and it worked fine. Took longer to heat the pipe up but the solder flowed fine and made a good joint.
@PaulSmith-pr7pv2 жыл бұрын
Great!
@Neil_down_south2 жыл бұрын
You read my mind - I've got a black and decker heat gun with a soldering attachment ... and some yorkshire fittings. I'll give it a go!
@LabRat6619 Жыл бұрын
Plus use customers electric.
@phoenixfridge1495 Жыл бұрын
Got set of pipe tongs and heads from a charity shop gor £1 As a joke Work well enough though Take time to heat tho Used on that one joint a little too close for comfort to wall Rest i did old way from habit and speed
@richardmccann92932 жыл бұрын
Just started learning how to solder at college last night! This is the best 'learn how to solder' video I've seen on youtube so far, and I've spent all morning watching them all. Cheers mate, really simple but sound advice and tips you gave out!
@LightningLuvsYouXD Жыл бұрын
Hey Richard would you mind telling me the class that you took I’m trying to look into getting into a class that offers things like that.
@dreadpirateroberts4052 Жыл бұрын
Best soldering video on KZbin……
@SkillBuilder Жыл бұрын
Thank you
@kerberos6239 ай бұрын
Thank you, very informative. soldered electronics before, just didn't know the flux would flow the solder all the way around for you. Good video.
@Chanesmyname2 жыл бұрын
Really interesting, I have a tiny, tiny leak on a push fit joint and I suspect the pipe if just slightly distorted, I think a solder joint might just cap it off. I will give it a go!
@gabrielhyder534125 күн бұрын
this guy saved me 1600$ love what you do
@jprevardАй бұрын
Great to see you, been a while for me. I’d avoid the wet rag . It’s the rapid temperature change that causes uneven cooling and a possible bad joint. 🙂
@andrewfitzsimons85092 жыл бұрын
Beautiful soldering
@LiquidSnakeSSJ411 ай бұрын
cheers - this video was very helpful. don't need to call a plumber anymore. sorted it out myself without any issues
@paulfinnonjoinery2 жыл бұрын
Had a kitchen to replumb a while back. Plumber was there to fit some radiators. Said he didn’t have time to replumb it so I did it myself. He was watching me constantly and I ended up with a leak and he danced about the room 😂😂 ohh how I laughed a few days later when he had to come back for a leaking radiator
@JemicoTX2 жыл бұрын
Pro Tips: When soldering a wet water supply pipe (for repair) ball up some loaf bread and stuff it into the pipe. Also, after sweating the pipe and while it is still nice and hot (right after applying the solder), brush on more flux to clean up the solder joint if you have made a mess of it. Not emphasized on this video: in order for the capillary action to work ideally, the heat from the torch should be applied to the fitting opposite of where the solder is applied (and well into the center of the fitting). This is to draw the solder into the joint effectively. Avoid contacting the flame with the solder!
@jra554172 ай бұрын
If you use flux to clean the joint you risk cooling it too quickly which can cause it to fail. If you solder properly there shouldn’t be any cleaning required
@edwardhuang2475 Жыл бұрын
Clearly explained and demonstrated, good job!
@josese4566 ай бұрын
Simple and very understandable explanation. Thanks for the class
@powerwagon3731 Жыл бұрын
I mark my solder with a Sharpie marker about every 1/2 inch to gauge how much is in the joint. Just subscribed!
@superawesomechannel2600Ай бұрын
well done for this amazing video, thank you so much because it's very helpful to me thanks once again.
@42RHD2 жыл бұрын
Thank you. Just finished City and Guilds level 2 Plumbing and Heating which I really enjoyed! It was a great course. Anyway soldering was a weak point initially, but I got much better with practice, and thank you for some really good tips. I use wire wool rather than emery but that's because it was what I was shown Cheers.
@andybb2 жыл бұрын
When I first did my Craft City and Guilds we had to learn how to wipe lead joints still got the scar to prove it, as molten lead flowed out of my moleskin onto my wrist never happened again after that
@42RHD2 жыл бұрын
@@andybb Ouch! I was sorry the don't teach lead working anymore, but not a bit sorry to miss out on the molten lead experience you describe!
@andybb2 жыл бұрын
@@42RHD Very much so do miss lead work though. We even learned stain glass window techniques as well and digging wells,oh the good old days lol
@42RHD2 жыл бұрын
@@andybb Stained glass window leading would be brilliant! Not so much the digging wells though!
@theondebray2 жыл бұрын
Nice & clear, esp. for beginners. One small appendium, IMV you are going in too close with the flame, and with MAPP gas, higher temperature, its easy to overheat the joint & burn the flux. I nearly always use a torch with butane/propane mix, lower temperature, takes a few seconds longer, but less likely to burn the flux. Also, butane mix a lot cheaper! I use the MAPP torch on bigger fittings when needed.
@hpevans9041 Жыл бұрын
Great video Rodger, very useful
@aprilsleanworkshop3110Ай бұрын
Great video, as always from a great Channel 🙏🏻
@ivideorandomstuff45912 жыл бұрын
i just couldnt believe you let that flux sit on your right hand the whole time. good video.
@SkillBuilder2 жыл бұрын
What is the problem? It is Laco not Everflux.
@pauls8262 жыл бұрын
Also very neat soldering roger
@sunkat76 Жыл бұрын
i like your soldering video. Very clear and helpful and timely. Hoping to join copper tap tails on new Kitchen mixer tap to pipe work on the back wall but the sink is 3 inches proud of the wall because we had deeper worktops fitted. I hate flex hoses on taps, I want to replace it with all copper. First timer here. Thank you.
@harrycallaghan222 жыл бұрын
Excellent advice and tutorial as usual Roger.
@SkillBuilder2 жыл бұрын
Thanks 👍
@-slurmdaddy-8147 Жыл бұрын
I had to buy a jet swet tool for $60 and sweat in a ball valve because my valves off my water meter don’t hold. I replaced old softener with whole house filter. Looks really nice, I even tappconned mounts and 3/8 rod hangers coming off foundation wall. I used bread trick once prior, it does work you just have to act quick.
@kennethreynolds8 Жыл бұрын
Thanks for the good tips mate.
@plumberparts2 жыл бұрын
Love you! 😂🥰
@SkillBuilder2 жыл бұрын
plumber parts I can't believe I called it plumber's parts
@plumberparts2 жыл бұрын
@@SkillBuilder ha! Everyone does! 😂🙈
@chrisshave71292 жыл бұрын
Thanks Roger. My dad taught me to always heat the pipework leading into the joint first and then move towards the fitting, and make sure you run the heat around the circumference of the fitting to ensure even heat.
@SkillBuilder2 жыл бұрын
Hi Chris I think copper is such a good conductor that it heats fairly evenly and quickly. If you mess around too long the flux evaporates so, in my opinion, just get on with it.
@gardgas1 Жыл бұрын
I'd always heat at the centre of the fitting, not the pipe itself
@nothingtoseehere852 ай бұрын
I used a sample of the SuperPower Plumbers SOS. incredible product Did my outside tap and fitted a radiator in the Conservatory. No leaks after 6 months and so easy to use.
@Daemiex2 жыл бұрын
after ive taken the heat away i use the flux brush again to clean the joint while its still hot then use the wet rag to clean it down while warm and it makes the joint/solder super clean and easy to see, i check the joint with a little torch and a tiny dentist mirror to look for pinholes, has never let me down to this very day and i feel that extra confident to move on knowing that chances are there not going to be a leak, the worst thing is to do alot of soldering like when doing a full system and not be super sure as you move along cause if you do a system and fill it and you have a leak theres gonna be alot of work to back track on to find a leak
@SkillBuilder2 жыл бұрын
I air test section by section then I can put the floorboards down with the pipes under pressure. I can then reinstate the room and move on.
@allmycarsisbroke3 ай бұрын
Wet rag is bad practice. Cools the pipe too quickly and messes things up.
@jra554172 ай бұрын
@@allmycarsisbrokeeven flux can do that. Do it properly and the flux trick should be required
@abbersj29352 жыл бұрын
Great video, thanks. As a keen self builder, done all that you've shown, but nice to see the experts say the same. End feed always looks so nice and neat, especially with formed bends. PS. I always deburr the pipe inside :)
@truthseeker77942 жыл бұрын
I'm a retired electrician/plumber (and never deburred) but am glad that you're a patient perfectionist. I always use wire wool pads to clean before and after although, I only use before soldering if the pipe is in an awkward place and I really don't want to go back and re solder it. Yes you're right, end feed are so neat when soldered correctly. I had a guy change my boiler a couple of years ago and his soldering was so good that you couldn't even see any solder on the end feed joints. I had to put my glasses on and shine a torch on the joints to just make out a very fine silver ring inside the joint. This guy was a master plumber. You often see plumbers cake solder all over the joint and pipe. I sometimes used solder ring joints for convenience or when I only had a couple of joints to make and they're not so bad. I also used compression fittings when cutting into the mains to fit a shower or washing machine as the pipes were often constantly wet and you also have a certain amount of adjustment with compression fittings, also you can easily turn an existing elbow into a tee joint. I must say that I've never used the new push fit plastic pipe and fittings so far (apart from old waste pipe fittings) and I feel that many builders have started to use the new push fit systems so they can fit kitchens and bathrooms without having any real plumbing skills. I've often come across their work under a bath, in an airing cupboard or in a loft. Just loads of unsupported un clipped spaghetti all over the place. Happy plumbing my friend.
@truthseeker77942 жыл бұрын
@@alemgas No my friend. I had worked in electronics for some time and so I found electrics quite easy to get into as it's much simpler than electronics. So I was completely self taught and set up as a self employed electrician for about 4 years. There were no laws to stop you doing this back in the 70's 80's and 90's (and there still isn't now, apart from the part P tax} and my work was often passed by the MEB and MANWEB, when I worked in Wales and I was often complimented on my good workmanship. I sometimes worked on site contracts beside college trained electricians and I also worked for two quite big well known companies. Some of the workmanship from some of the so called trained electricians was appalling. Many of the sparky's just signed up to be an electrician on careers day at school and so that's what they ended up doing. But many of them didn't have a natural aptitude for the job. I feel that I did. So I got into plumbing because people were asking me if I could fit electric showers. So I fitted an electric shower in the house where I still lived with my parents. My dad did the plumbing and I did the wiring and it worked out fine. I then had a go at the plumbing myself and found that it was quite easy using compression joints. I Then bought a blow torch and experimented with solder ring joints in my garage and that was a massive game changer. The joints were so cheap and neat and they didn't leak. So I was now a plumber. I installed washing machines, kitchen sinks, bathrooms and outside taps. I also fitted gas cookers, fires and boilers. Some of the plumbers I worked with on building sites were qualified plumbers but also did gas work because it was basically just plumbing. We had the necessary gauges and test equipment to for leaks but of course, it wouldn't be enough these days as it seems that nothing can be done on a boiler these days without an hours worth of computing. So no my friend I am certainly not a dabbler. I was a carpenter when I left school in the early seventies and later did painting an decorating. I've also been a carpet fitter. I started work at the age of seventeen and retired at the age of 48 so I've crammed a lot in. Oh and yes I've seen many "electrician" dabblers along the way. Kitchen fitters are the worst who think they're electricians. They don't understand that when you reduce a cable size you need to fuse it accordingly. Thanks for your reply.
@seane6616 Жыл бұрын
@@truthseeker7794 Nice :)
@truthseeker7794 Жыл бұрын
@@seane6616 Thanks Sean. I'm just sipping a glass of newcastle Brown now. What's your line of work my friend.
@NobleNobbler Жыл бұрын
That flux tool is rad, I want one!
@Toob412 жыл бұрын
Thank you for this masterclass. You are a Jedi master of pipework!
@shannonj1000 Жыл бұрын
Normally Great advise, I would always advise heating the bottom fitting 1st, as heat rises.. never use a wet rag as you say the fitting can crack wait until it has suitable cooled down..
@jbchicago1970 Жыл бұрын
Thanks, good job explaining!
@MrSilvervw Жыл бұрын
Fantastic content 👌 👏 👍
@PalastangaАй бұрын
Mint video, really useful. Thanks.
@blankroomsoup6662 жыл бұрын
I like to use scotch brite for cleaning, gets around all bends and into tight corners better. As for air pressure testing, especially on compression fittings, I’ve noticed it takes much less pressure than water to leak- thought that was interesting.
@chrisholt24742 жыл бұрын
Great film, thank you Roger. 👍👍👍
@endurojimmy31092 жыл бұрын
I worked for a local authority. We weren't allowed to use end feed on potable water only Yorkshire as it was guaranteed lead free solder. We went virtually all crimp for instance purposes.
@marfu_lee2 жыл бұрын
As a DIYer I ended up buying an expensive blow torch because the cheap one flared when upside down and the tip heated up and I burned myself. I also use a mirror to check that the solder has flowed all the way round.
@mrboyban2 жыл бұрын
Rodger master class is phenomenal! Thanks for making it available.
@Lc-is8vn2 жыл бұрын
Great tutorial as always 👍
@h.b2029 Жыл бұрын
Excellent. Very helpful. Thanks. God bless.
@KendalSmithy2 жыл бұрын
As a DIY plumber I'm chuffed to learn that I've been doing it right all along but using the Yorkshire pre-soldered fittings. However, I apply far less flux, using my finger to apply the slightest trace of flux on all the surfaces. This means it doesn't run down the outside of the pipe and makes a much neater job. And I've never had a leak yet ... if you see what I mean.😉
@alext8828 Жыл бұрын
Interesting. I shall try that and if it doesn't work, I'll be coming for you. You tryna mess up my work???
@SnakZ Жыл бұрын
i use my heat to burn/blow it away or just wipe it, solder should follow the heat into the fitting.
@5084204 Жыл бұрын
Try the grey flux with added powdered solder. MUCH, much neater jobs and once the flux turns to silver (from grey), you apply the solder. It is thicker, so less ugly "spills".
@paulstokes39310 ай бұрын
Try applying flux with finger splits, you only do it once! Tradies fingers always split during cold weather 😅
@KendalSmithy10 ай бұрын
@@paulstokes393 Good point but my fingers split during the winter whatever. Super Glue to the rescue!
@Nyck4616 ай бұрын
Very nice video. How to solder and where to add heat when soldering a shut off valve that has nylon parts like nylon ball ?
@jasoncornthwaite83872 жыл бұрын
been a plumber for 40 odd years and remember being a bright eyed apprentice going into the plumbing merchant and always getting my professional plumbers magazine just to go to the end of it to read your joys of being a plumber,,,lol now i know
@jasoncornthwaite83872 жыл бұрын
always blood , sweat and tea,,lol
@Fred-rv4qv8 ай бұрын
Excellent presentation! Thank you!
@francisexperience2 жыл бұрын
Excellent training video thanks
@philipwood1236 ай бұрын
Great tips Roger
@Anakinuk0072 жыл бұрын
As a fellow plumber I concur to leave the pipe well alone once soldered. What’s the point in using a wet rag to save yourself a minute or so, risking it leaking once you fill up? I saw a Polish plumber solder a joint three times in a row and each time it leaked, and each time he applied a wet rag seconds afterwards. I took over from there lol. Also I’ve been called out to repair corroded pipes which were no more than three years old, caked in flaky green old flux plumber too lazy to clean properly. With Yorkshire fittings what can happen is the solder can either drip out, or doesn’t look quite right when you can’t see a nice solder ring all the way around the fitting. So then you add more solder just to be sure, which kind of defeats the point of using them and at more expense. Also I always make a pencil mark the depth of the fitting, as frequently the pipe moves/gets knocked and you think it’s probably ok, but then you have to be 100% it is in properly. Having a pencil mark means you know for sure everything is ok.
@johnchampion781911 ай бұрын
Very well explained, you're one of the best on KZbin.
@strummer66422 жыл бұрын
I've always found those pipe cleaners/deburrers, the ones with the stiff wire heads, work well to start with but as they wear they make less contact with the pipe, and it's back to steel wool
@SkillBuilder2 жыл бұрын
You are right, though I don't like steel wool because it is bitty
@nico101gaming2 жыл бұрын
I’m a heating engineer by trade. Not bad on the soldering. But just a few things. you should start from the lowest joint and work your way up, never top down; when you get to the top joint the heat should be then hot enough to instantly feed your flux in with little heat. Also mapp gas is a pain in the arse for soldering, gets everything too hot too quickly, strongly suggest always soldering with propane on a gentle heat and take your time 👍🏻
@SkillBuilder2 жыл бұрын
What you say works in reverse, start from the top and the fux runs down. Then when you do the bottom you have only to apply a little heat and the solder will draw up. You can then remove the heat and avoid the solder runnning down the pipe. With your method the heat is still in the bottom when you do the top so it can run. Also Mapp gas is now just propane but they kept the name Mapp.
@garychadfield5522 жыл бұрын
To add a bit of extra solder to a solder ring fitting is just daft, you may as well save some money & just use end feed fittings. A lot of my pipework is in chases behind tiles, feeding showers & basins so the low profile of copper end feed fittings is essential.
@Jay-yy9ol Жыл бұрын
Nice info on the set up. I was hoping you would talk about another key thing to understand and that is the science around heat and how the solder reacts to it to draw it into the connections.
@SkillBuilder Жыл бұрын
Hi Jay The trick with all these videos is not to overwhelm the viewer. Some people care about the science and others don't
@johncoppock38232 жыл бұрын
Great video. When should we use MAPP gas then. I chose it so I could do big sizes and brass fittings (which were always a problem for me even with lead solder). Many thanks
@SkillBuilder2 жыл бұрын
I am not sure MAPP gas is sold now. They kept the name but it is propane
@southeastgasservices2 жыл бұрын
@@SkillBuilder still called Mapp gas here in Ireland. sold everywhere, not cheap though, still it's the only bottle (with the Rothenberger super fire torch) that will work upside down. something that's very improtant, those stupid gas torches you buy in DIY stores can only work in the upright position. soldering under ideal conditions is one thing, soldering virtually standing on your head is something else, well you know what i mean...
@JemicoTX2 жыл бұрын
@@SkillBuilder , MAPP was a trademark name representing methylacetylene-propadiene propane (48% methylacetylene, 23% of propadiene, and 27% of propane) having a flame temp of 5300 °F when mixed with oxygen or 3,670 °F when combusted with atmospheric air. Propane burns at 3,600 °F. MAP Pro gas (or any of those yellow cans) sold today is propylene (99.5%) and propane with a flame temperature of 3730 °F
@johncoppock3823 Жыл бұрын
@@JemicoTX So assuming my x2 yellow cylinders from a few years ago are real MAPP I'm going to have to relearn again. Thanks for the info
@davidsunderland8063 Жыл бұрын
Thanks, very helpful
@slavric2 жыл бұрын
I like your videos a lot. With this one I was checking if I was doing a good job these days, since I'm building myself a new central heating system with 2000l buffer tank. Cutting copper pipes and soldering is so rewarding. I had to fix one joint where copper to brass joint is screwed in to iron fitting and it was leaking, since I've put too little sealant string. I separated it in a minute with no problem, fixed the threaded joint and resoldered back together. If only it would be a bit cheaper. Copper pipes are really expensive.
@JAHManeShaker2 ай бұрын
When heating, should you heat the pipe or the fitting or a bit of both, for the solder to pull correctly?
@jmspr1 Жыл бұрын
amazing skills
@peters9943 Жыл бұрын
wow clean as hell. thank for this.
@petebateman1432 жыл бұрын
Solder comes from the same root word as solid. Solidus "solid", solidare "fasten together". It's the French that turned the Latin into soudur which is where I assume the American pronunciation came from. You can call it so'der if you like, just make sure your joint is so'id.
@johnstewartrichards59222 жыл бұрын
Honi soit qui mal y pense. Funny always thought ‘Mericans dropped the L to sod off…
@bodinian9 ай бұрын
American here and I'm curious about the L getting dropped in our pronunciation too. I'd seem silly if I was the only local pronouncing the L so I just go with it.
@paulfrost89522 ай бұрын
Don’t you mean the English pronunciation!?
@petebateman1432 ай бұрын
@@paulfrost8952 No, we call it solder in England, not so'der.
@paulfrost89522 ай бұрын
@@petebateman143 mea culpa ah I thought you meant the Americans called it solder, as they seem to think they speak English🫢🫣
@thelancasters1111 Жыл бұрын
Excellent and to the point
@alext8828 Жыл бұрын
The best videos on the internet. Al Gore invented the internet, you know. You know that, right?
@Ste20232 жыл бұрын
Love copper . Those pre-solder are great (I double up and solder on edge ( belt & braces Roger lol )
@wemcal3 ай бұрын
Great video and great information
@adammmadi1850 Жыл бұрын
Great job 👏
@rezganger Жыл бұрын
induction? is that something one can use where "no open flame" rules?
@rekinlas Жыл бұрын
Great video! Question: If I'm capping a pipe, how do i ensure no flux is left on the inside where I can't see it or clean it out with flowing water? Should I just make sure not to flux all the way to the pipe's end?
@SkillBuilder Жыл бұрын
Flux is not as corrosive to copper as some people imagine. It is a worse problem in steel radiators where it lies in the bottom. I would not worry about a little bit in a dead leg
@austinvert86262 жыл бұрын
Hi Roger. Good video. I have been following your videos for some time, and always enjoy your content and help. Regards this video, i go back to the Eighties decade when i did a little DIY on my home copper pipes in Yorkshire and add solder joints. They turned out well, and i enjoyed the process. I am commenting today with a question for you. In Australia where i live, doing your own plumbing and electrical work is illegal for the general public. I think changing washers over is the limit for the general public here. What is the story over there in Great Britain regards the public doing their own plumbing work? Cheers, Greg.
@southeastgasservices2 жыл бұрын
@@jonh1808 doing your own electrical work is high-risk. and stupid really. all electrical work should be done by a qualified electrician. why risk a fire or even worse, somebody gettin' toasted....
@sativa9598 Жыл бұрын
Awesome vid mate. I'm about to attempt to fix a shower breach myself because my insurance company only covers the rendering & paint. Wish me luck.!
@1mrsleepy12 жыл бұрын
First time seeing pre flux fittings before!
@SkillBuilder2 жыл бұрын
It is not genrally required because you get flux inside the pipe end. I just do it out of habit
@vajindertaak315811 ай бұрын
Great video, going to set up a test rig like yours before I tackle the pipes in the bathroom for the new slimmer towel radiator. What happened to the plastic clip? Cheers!
@Martycycleman2 жыл бұрын
Nice one Roger you got the job. I tend to start at bottom, heat rises and I play the flame onto the pipework first with a little flash of heat onto the fitting as the flux flows. Never had a joint leek in 50 years. Biggest soldered fitting would be 75mm Yorkshire in the winter. This took two blow torches and some solder and not just one fitting, thousands. My pet hate is uncleaned joints, very unprofessional.
@SkillBuilder2 жыл бұрын
, I am amazed when people tell me they have never had a leak, I have had loads over the years. I had one leak which was due to a hair in the flux brush coming loose. The best ones are where I forgot to solder a fitting and it held for ages. Do you debur?
@PBYM792 жыл бұрын
@@SkillBuilder did this just last week! Soldered a 22 - 22 - 15mm tee. Totally forgot to solder the 15mm bit! I'm a painter and decorator by trade so maybe should stick to that in future! 😆
@Martycycleman2 жыл бұрын
@@SkillBuilder Why? it's all down to preparation. How many joints do you think I've done over the years?
@Martycycleman2 жыл бұрын
I will only deber micro bore pipes for obvious reasons.
@fiercefix2 жыл бұрын
@@Martycycleman 2 joints thats why you've had no leaks! Or you've never been called back to sort any out because you sound like an arrogant c***.
@Johny40Se7en23 күн бұрын
That's great tips, cheers. You know when you're on a job, what do you do to extract soldering fumes when you're in tight places?
@SkillBuilder23 күн бұрын
I hold my breath
@Johny40Se7en23 күн бұрын
@@SkillBuilder LOL 😆😅 Seriously though, what do plumbers do, especially when you're using the leaded solder? 🤔
@jamie35662 жыл бұрын
Great stuff Rodger,,, I'll be interested to see pressure test on pipework, it's something I haven't done yet but would save me alot of heart ache going forward.
@andersonec1 Жыл бұрын
Thanks for the tips. If a connector is de-soldered and removed, can I clean the pipe and solder another pipe / fitting onto the old solder or do I need to cut it off ?
@tinytonymaloney78322 жыл бұрын
I personally do prefer old fashioned copper pipe and soldered fittings, they have stood the test of time, unlike modern stuff. I also like to wipe round the joint with the flux brush while hot to wash the joint leaving it clean and shiny followed by a wet cloth to remove flux. Takes a bit longer but im no longer in it to make money, i only do stuff at home now, like James, I had enough years ago and went to work for somebody on a permanent site. 👌 Just a comment, the middle brach of the tee, the side facing the camera didn't seem to get the full solder flow.
@johncoppock38232 жыл бұрын
Great video. Can you do a video on getting water out before soldering, hot water flushing, and pressurised testing. I've only done it once, using a car tyre pump for blowing the air out. Didn't pressure test after which would be good to do. Many thanks.
@martintheron1386 Жыл бұрын
I read somewhere to put bread inside pipe which absorbs water and moves it away from joint
@johncoppock3823 Жыл бұрын
@@martintheron1386 I like old fashioned methods. You have to have the courage to give it a go. I've not cut into the walls yet 😁
@nobodydoesithalfasgoodasyou Жыл бұрын
I use a 50ml syringe and windscreen washer hose
@JohnStowers2 жыл бұрын
Any comments on lead vs. lead free solder for plumbing? As an electrical engineer I miss the days of leaded solder - worked so much better - I see you can still buy leaded solder for plumbing. Putting aside the fumes, what would you recommend?
@paulboyle8522 Жыл бұрын
Great video Roger. Doing up an old house at the minute and it has compression joints everywhere which have been there for about thirty years. Should I replace all of them with soldered joints?
@SkillBuilder Жыл бұрын
If they aren't leaking and you don't need to change them then leave them but if you need to run new pipes I would solder them.
@leonperry1232 жыл бұрын
I do my own plumbing. But it was nice to know how much solder to use on the none Yorkshire joint. I'll remember that. The good old bur or not to bebur the cut joint.
@samevans4525 Жыл бұрын
As a shipyard pipe fitter you wouldn’t believe how much damage I’ve seen caused by people not deburring their pipes.
@bicolouredprawn Жыл бұрын
I never used to deburr my pipework, when I was trained in the early 2000's it was never really emphasised how important it is, but I started doing it a couple of years ago, mainly because I treated myself to a battery pipeslice which creates a significant burr, now I do it every time without fail, and I wish I'd gotten into the habit years ago.
@tig844010 ай бұрын
Make sure you pickle your ships pipes when needed too! 😁