I have a very important question: how did you manage to increase the speed by 20 m/s? Have you changed only the slingshot and the butt ? Or have you also replaced the tubes and the length of the stretch ?
@atsushifactorymanager Жыл бұрын
just replaced the rubber Please watch this video ↓😁 kzbin.info/www/bejne/a6C8Y3qKpJ54bMk
@АлексейСавельев-ф4ж Жыл бұрын
@@atsushifactorymanager That is , how did I understand all this magic with speed happened because of the replacement of factory rubber bands with your modified ones ? And the replacement of the slingshot itself with a large one , how did it affect the speed ? Isa why did you change it ? The recipe for the perfect rubber, as I understand it, is (3060-2050-1632 ) ?
@atsushifactorymanager Жыл бұрын
@@АлексейСавельев-ф4ж Widening the fork width increases the hit rate. The effect of tube-in-tube is the same as taper cut of flat rubber 3060in2050 has deformed rubber and unstable trajectory I tested this 🙂
@АлексейСавельев-ф4ж Жыл бұрын
@@atsushifactorymanager Ok, I understand, I want to tell you that, in my opinion, you made a mistake in the manufacture of rubber bands for your last shotgun, since the photo shows that the internal rubber (green) occupies only 50-60% of the volume, although a minimum of 75% is needed for great efficiency, you can do this understand by watching your own videos from September 1, 2021 and September 12, 2021…. plus, you seem to have put 2 simple plain rubber bands that are not modernized; if so, then when fired, they will slow down good rubber and thereby spoil the speed! I hope in a short video you will please us with your new invention or refinement!🎉
@atsushifactorymanager Жыл бұрын
@@АлексейСавельев-ф4ж The reason why I mixed the normal tube is because the rubber loses the weight of the bullet. This is because if this rubber is tube-in-tube, it is too hard for me to pull. It may be faster to remove it, but I don't know unless I test it. Thanks for your comments and advice😁
@yuriklaver46392 жыл бұрын
Do the flat bands cause problems with the small fork as well?
@atsushifactorymanager2 жыл бұрын
If you pull a short rubber long to increase the bullet speed Experience shows that this symptom often appears. But I don't know everything, I'm researching Thank you ^^
@eddiehughes91372 жыл бұрын
Hi loving your slingshot rifle can I ask what flat bands would you suggest for 10mm steel balls for hunting
@atsushifactorymanager2 жыл бұрын
I use gzk 1mm for flat bands🙂
@eddiehughes91372 жыл бұрын
@@atsushifactorymanager What size ammo do you use and what are the tappers
@willem6865 Жыл бұрын
Hello! Can you share the 3D printed connecting parts of this gun stock?
@atsushifactorymanager Жыл бұрын
sorry i don't share thank you🙂
@АлексейСавельев-ф4ж Жыл бұрын
Hello, can you tell me ? What is the coefficient of stretching obtained on this slingshot ? Or how long are the rods installed here ?
@atsushifactorymanager Жыл бұрын
Normal pull width is 60cm Rubber is 11cm Elongation rate 5.4 times🙂
@АлексейСавельев-ф4ж Жыл бұрын
@@atsushifactorymanager
@АлексейСавельев-ф4ж Жыл бұрын
@@atsushifactorymanager Okay, and how about durability ? How much rubber is enough before replacement ? Have you tried to make a coefficient of 4.8-4.9 if yes?! then what speed was achieved ?
@atsushifactorymanager Жыл бұрын
@@АлексейСавельев-ф4ж I shot more than 40 shots with 5.4x rubber So I haven't tested it with other rubbers I think 10m/s will go down at 4.9x🤔
@АлексейСавельев-ф4ж Жыл бұрын
@@atsushifactorymanager You 've only fired 40 shots and the rubber is fine ? or just 40 shots before the rubber broke ? Just an inaccurate translation is not always clear
I created 3D data that matches the stock of the air gun and printed it with a 3D printer. thank you😁
@ulungprabowo Жыл бұрын
Thank you for making this. This is the only video on youtube showing the grouping of that china slingshot rifle. By the way what is the distance from you and the target?
@atsushifactorymanager Жыл бұрын
My test is not perfect, but I hope it helps. 15m to target Thank you🙂