Small Radio Receiver Board | NRF24 + Arduino

[@ELECTRONOOBS]

Sign up at ELECTRONOOBS.io: electronoobs.io/ Follow me on FACEBOOK for more: facebook.com/Electronoobs help me on Patreon: www.patreon.com/ELECTRONOOBS

[@Kitsu_no_mirai]

Put a capacitor between the coil to smoot out the movement. It work for mine

[@74anuradha]

fool

[@shantotorofder3916]

hey plz plz give me the code of controlling the coreless motor and 2 actuators

[@Rouverius]

Impressive. Looking forward to the paper plane build

[@Nono-hk3is]

This is a great idea. I'm excited to see how the plane turns out.

[@rafaelcabelo6616]

I gotta use an opamp as voltage follower to smooth the pwm signal. An rubber band to hold the flap in position may help too.

[@Abcdefghijklmnopqrstuvwxyz121]

Great video @electronoobs ... Add a big value non polarized capacitor in parallel to the coil, remove outer magnet which is on coil and try to use some elastic material to keep flapper at middle position,you can use that white isolation paper used in induction motor winding

[@jasmine2501]

This is pretty cool - with the full ATMega 328 on the receiver you could do some pretty cool automagical flying!

[@Sahil._.S]

this is really cool...... its because of such amazing youtube channels that i was able to learn so much about arduino and start my own project making business here in india(mumbai city).

[@ELECTRONOOBS]

So glad to hear this!

[@shantotorofder3916]

@@ELECTRONOOBS plz tell me where is the code for controlling the coreless motor and the actuators

[@nidhikhamayacha]

Sir does this receiver supports the right hand joystick?

[@thp1202]

damn i wish i had your skills, great job!

[@franzhagemuller6413]

Depending on your code it may be a good idea to use the timer registers of the atmega directly. Arduino sets the PWM Frequency pretty low. If you directly access the timers it would be possible to get above 20khz which should be stable for your actuators.

[@dipanjanmaity6614]

I think you can use a simple low pass filter in which it will take big previous value and very small current value. I think this can make the move of the flapper more analogous. As always awesome project

[@durandile]

Once again: great project and great video! I love how you're project are all compatible between them and all the different things they can do

[@rishavsrkr6948]

Please make an update video of the micro brushed drone Please.

[@ABID5]

you're very innovative

[@user-nq5hy7vn9k]

Can you please make an update video on the brushed micro arduino drone

[@khageshroy7766]

Shall impatiently wait for the paper plane😍...

[@rramirezx8738]

Good explanation and excellent Project ELECTRONOOBS.

[@MCsCreations]

Beautiful job, dude! 😃 Looking forward to the paper airplane!!! 😃

[@ELECTRONOOBS]

Thanks!

[@shantotorofder3916]

@@ELECTRONOOBS where is the code of controlling the coreless motor and 2 actuators plz give me that code plz or tell where is that code..

[@anmolkumar6704]

@@shantotorofder3916 use the h bridge ic to change the direction of flow of current in the actuators some examples can be found online

[@andrewmitchell5807]

Your intro is awesome

[@darshanprakash2156]

Can we use this for brushed drone without the motor gearbox??

[@officializm4171]

You are very good as always. Keep it up👍

[@shantotorofder3916]

hey where is the code that you controlling the coreless motor and controlling the actuator

[@fuhadrock6370]

hey my best idol for electronics.. where is the code for controlling the coreless motor and the actuator... which code need to controlling coreless motor and the actuator...

[@SurajGrewal]

Maybe it could be made smaller with 4 layers and lighter, if you maintain the same thickness, assuming the current one is 0.8mm thick. Though, it'll become expensive (cost per via goes up and so does via count)...could also use attiny or some smaller package for same IC

[@janmenzinga]

Have you thought of the idea of selling them complete? My soldering skills are not good and sure not with those tiny parts.

[@jmibk]

And again the SPI port is missing to program the bootloader to the ATMEGA chip.That is neccessary for using the ATMEGA with the Arduino IDE.

[@doom3599]

I want to use brushless motors with this module Will it be compatible with these motors

[@drogobero4479]

oddly enough with all of these receiver videos, I'm looking for size, rather than weight, when looking for a smaller receiver. Do you have any recommendations that fit within a 1.5cmX2.5cmX3cm space? Cost is an issue, but the servos I'm planning on getting are rather cheap, so a splurge on the receiver wouldn't be too awful.

[@alanbacknd3120]

Great Video !!! Can you make a HC12 unit also. greater range. Thanks

[@WorldRecordRapper]

Use gold wire and wrap it tight and clean magnets!

[@ashloverscn]

can u make it more comercial like bind and fly feature with nrf24l01

[@ajayjoshi_aj]

u can use instead of pla material some that kind of material that is ferro magnatic

[@shantotorofder3916]

hi where is the code of controlling the coreless motor and 2 actuators

[@drssound5273]

Wow good pcb Good luck 🙏🙏🙏🙏🙏

[@officializm4171]

Can you make examples with stm32 MCUs and design pcbs with rf or esp82. Thanks.

[@epismania3222]

But if I want to know drone position and altitude I have to put not only a receiver, but also a transmitter onboard and send data to the controller. Am I right?

[@ELECTRONOOBS]

The nrf24 is both receiver and transmitter

[@epismania3222]

lovely, thank you

[@khageshroy7766]

I wander how is your timing so great 😍... I was thinking of making a drone... And you have just pumped up the perfect tutorial for making the most important part of my project 😣... Love you 😍😆

[@ELECTRONOOBS]

Thank you!

[@khageshroy7766]

@@ELECTRONOOBS welcome sir😄

[@user-nq5hy7vn9k]

How are you gonna use it in a drone ?

[@khageshroy7766]

@@user-nq5hy7vn9k obviously I can't directly use it in a drone... I need to modify the design a bit... But that's just a bit coz he already provided the necessary framework for that purpose... And am almost done on making it a drone controller😄...

[@user-nq5hy7vn9k]

@@khageshroy7766 could you please make an updated video of the design. I am new to electronics and want to learn more

[@johnacsyen]

How many receivers can one transmitter talk to

[@sarthaksuman6554]

🤩🤩 Waiting for rc paper airplane....

[@johnedwardcapellan9537]

hello, i've been a fan. and you're videos helped me understand everything but sadly there's no video about moisture sensor. i just want to ask if it's possible to have a moisture sensor automatically trigger a relay to enable watering system and have the android app get the value of the moisture sensor and has the option to trigger the relay too via android using hc-06 or 05 to enable watering system i'm going nuts T_T

[@tohinmahmud3354]

i did not find 5volt pwm output on my nrf20l01 Arduino receiver . for that reason i could not turn my small core less dc motor with full torque and full speed.i am using same mosfet which you also used. please give me a solution.

[@fatamorganaproject4696]

What we can make nrf24l01 clone using arduino ....

[@floppylab]

good job, you're the best. I have a problem with nrf24l01 that doesn't connect to the receiver, the program I used is what's on your site can you help me out?

[@kayquexavier]

Impressive project, but unfortunately to me it's not viable to buy the atmega ic separately, is there a way to make this board with the holes to solder an Arduino pro mini on it?

[@myetis1990]

goood job friend but there will be a problem in terms of receiver comm range because of ground plane under antenna of the nrf module, at least ,you have to remove this part of ground plane or you can set a slot under antenna, I suppose that it will communicate around max 50 meter, normally it works around 100meters, Ithink.

[@alvarobyrne]

dare to ask: what was that video in which you made a multiturn potentiometer out of a trimmer with a spring and a 3d printed mechanism/case?. thanks in advance

[@Stefan.05]

Does the Spitfire flie?

[@PowerScissor]

Could you figure out a way to program wirelessly? Like how Crossfire & FrSky hobby receivers can update their firmware OTA using the same wireless connection?

[@Travis_Yu]

Maybe a DAC for the actuators?

[@eleven_001_11]

U are a PRO...

[@anonymoususer900]

Awesome bro thanks a lot for making this

[@abinesh.g6833]

Super bro,please make a 8ch receiver

[@onlynation1509]

I want to video on small video transmitter and receiver which is used in drone do you have any idea how to make it

[@mastermaker8782]

Bro u were the best channel for me who gives all info for project but now u have change we cant order from jcpcb and u have only given schematic for pcb not for electronics now i unable make this

[@sagarbansal7534]

Buddy, urgently I need your help in designing my PCB. How can I contact you?

[@premkumarms1772]

Is it compatible with your pc tx

[@iforce2d]

It might be nice to mention that a new atmega328 does not come with an arduino bootloader, so unless you're gonna pull one off an existing arduino to use, you will not be able to just 'upload the code' as you're suggesting. You'll have to flash the bootloader yourself, which can be rather finicky and annoying.

[@ELECTRONOOBS]

Hey, thank you iforce2d for your comment. You're right, that's why in the text tutorial on my website: electronoobs.com/eng_arduino_tut105.php on part 3.2 I show how to burn the bootlaoder in case you have a brand new chip. Btw, thanks for all your videos, they are great and helped me a lot of times. Have a really nice day.

[@okannuryuz1484]

Great job again !! But does this reciever supports ppm signal and can we have more channels like arduino pro mini+nrf24 combination ?

[@TheDambo1]

Why ground plane/routes under antenna?

[@aberateklehaimanot9804]

As always fantastic video...thanks for sharing

[@PaulRichardson_Canada]

Just Wow ! Awesome.

[@humbertobruniguitar]

Great tutorial ! Congratulations. Looking forward to see the micro paper Plane. Although (I think) you’ll have big stabilization problems. IMHO, of course. Q: Did you solder all the SMD components? Anyway thanks a lot for this Great Tutorial.

[@mmdnaderi7183]

another good video keep it up and I had a question , how long this module works? recently I wanted to buy them and I'm not sure how far they can establish the connection? tnx

[@ELECTRONOOBS]

Using the amplified antenna for the transmitter I had good connection up to 700m. But check iforced2d channel. With a good antenna he had signal up to 10Km. That's crazy.

[@mmdnaderi7183]

@@ELECTRONOOBS OMG , tnx for information

[@rajatmamidwar8591]

@@ELECTRONOOBS 10km thats really cool

[@anuprashpradhan1016]

Sir teach us how to add camara as well

[@technocrat9984]

With these components u need to increas the thrust of motor..

[@aklapotherpotherpothikrebh603]

How to make the circuit

[@vdm7776]

Thanks for video and for your job! That time of delay between joystick and servo movements?

[@maronilabuni5935]

How to upload code to the pcb

[@shoumikahmed6373]

It's quite good.....

[@agusheripurnomo2881]

Can I request the project? esp32 module and bluetooth itag to control the lamp relay

[@tusharmahanna8543]

A long time follower of your videos.. I m currently having issues for connecting my barebone arduino with nrf24l01+ ... Works perfectly on arduino uno and nano .. but not in barebone... Can you make a video about making barebone arduino with nrf24l01+... Not more info about it in internet.. so plz.. plz make a separate video.. only barebone arduino with nrf24l01

[@mackizzer6071]

I’ve got a butch of old motors from old iPads that I found that were trashed, thank

[@rajeshsharma-ng3cb]

Sir i have an idea of an amplifier in which I want to filter the sound to high pitch and low pitch at the input and then feed the amplified sound to a woofer and a satellites, I just wanted to eliminate the use of band pass filter at output. Though this would be single channel but it would be very efficient, and no one stops us from using 4 ch amplifier

[@Abcdefghijklmnopqrstuvwxyz121]

You mean sending signals to satellite using sound🤔

[@giancarlomejia5496]

Hello my friend about coil actuator how i cand do it please could publish about it or where i find it

[@duncanx99]

Hola, buenos días These actuators look very interesting. A link to them would be really helpful. Graciás

[@giancarlomejia5496]

@@duncanx99thanks my friend but where is the link?

[@duncanx99]

@@giancarlomejia5496 The comment was aimed at the creator, in support of your comment. I want to find the source for those small commercial actuators. Sorry for the confusion...

[@ranganatennakoon]

love it , nice

[@Zigzag-k]

Can you please provide Dimensions please ?

[@salazar.eduardo]

Nice video! Keep it up!

[@Drxxx]

Cool project

[@raulcabe3392]

looks great, i can't wait for paper plane. Do you have any project with FPV?

[@hunkbol6154]

Sir it too big for project hence sir can you make board with receiver ic solder on board please

[@Althu-blog]

good and power full video good jod brother

[@imamnegeri8825]

Please make this pcb with ic ch340 as usb programmer＆ atmega328p au in one package bro, maybe u can share the schematic? Thanks

[@zainnoman3145]

0:11 Every 9gagger: banana for scale!!!!!

[@muhammadsiddiqui2244]

Why don't you use servo motors instead of the actuators.

[@tonim.9460]

Because for a paperplane servos are way too heavy

[@muhammadsiddiqui2244]

@@tonim.9460 Got it.

[@WorldRecordRapper]

I was like "this dude's not 1337 he's just a cool hacker" then he prints and Actually. makes. His. Own. Actuator! Yoooo über badge

[@RahulVanjeri]

The atmega338p au chip doesn't come with the bootloader on it so we have to flash one on it ... I didn't know this before and I soldered it to the board in the video now I'm trying to flash a bootloader using the method here www.instructables.com/id/How-to-Burn-Bootloader-Onto-Atmega328p-AUSMD/ But I'm getting an error(invalid device signature 0x0000) hoping someone can't help me out

[@anurudhandru2958]

Waiting for the update video

[@aniszed3641]

wow so amazing good job man .I've 1 qst , can this work with 5 servos ? thnkx a lot .from Algeria

[@ELECTRONOOBS]

The system could work but the PCB dose not have 5 outputs...

[@aniszed3641]

@@ELECTRONOOBS can you make a pcb for more than 4 servos plz .thanx a lot nd wish you all the best We benefited a lot from you

[@DharmeshTechZone]

Thank sir for focuse on paper plane, as i have request in previous comment

[@Thunder_Owl]

Nice!

[@ofsanjay]

waiting for the next video. :-)

[@jaishankarm5920]

Super 👍👍👍👍

[@VideoStefan17]

awesome!

[@jaishankarm5920]

Make through hole version of PCB Also for beginners

[@BharatMohanty]

I want that rc car..(with board of course)

[@hunkbol6154]

Sir try 13.6k Herts frequency

[@Nono-hk3is]

BTW check out Carl Bugeja's channel (kzbin.info/door/dxTCCRnQgfi2vr2fZupYIQ). He's working on lightweight PCB motors.

[@doom3599]

Can I pay in rupees

[@siddharthmali5841]

Great

[@skaregowda1471]

I need toy drone remote and resiver