Smart Wood Recycling Project // Extremely Creative Pocket Folding Table Design From Ugly logs

Smart Wood Recycling Project // Extremely Creative Pocket Folding Table Design From Ugly logs

[@mondherayadi]

Is So Great …❤ You are Fantastic..👍🇨🇦

[@beatricekarrerulrich652]

Ich möchte diesen Tisch nicht, aber es ist faszinierend die Arbeitsschritte zu zuschauen und die Maserierung des Holzes ist toll!

[@uweploeger511]

A table for heavy workout, but the grain looks fantastic after spraying!

[@borissorin2601]

a unique engineering design and if someone sits in the center and this happens and very often there will be laughter

[@talleyrand2739]

well done looks great and very handy when camping

[@jjtrades7186]

you never know when a wild dinner might break out

[@rosellabill]

You always make fantastic videos. Thank |You

[@dang6832]

If I had that finish on my hardware I’d be pissed. Spray, then finish. Cool design though. Nicely done, except the spray.

[@MrDhalli6500]

Because I know when I see power tools and flip flops, I know I'm in for a high quality video.

[@johnadamski4012]

🌲🍀🐾⚒📐🔨I've seen these portable tables before. Nice tables to bring along while camping🏕 (needs a vehicle🚘 to carry) & fishing🎣. This one has quite beautiful wood grain. Look's a bit heavy, but it's that much more "rigid" (stronger) too🔨📐⚒🐾🍀🌲.

[@AnneThiessen-xv3dd]

Very interesting work!

[@Heroturtle112]

Das schöne Holz so billig zusammen geschustert. 😢

[@JohnDlugosz]

How did you get away with using the slabs immediately after taking them off the log? I would normally expect the kiln to be the next step, followed by a couple years seasoning. Even then, I would expect the crotch wood to be full of internal stress and deform when it is cut through; though that might depend on the species (my experience is with mahogany). What is the moisture content of the wood when you started the table?

[@couttsw]

Screws in at angles, it's why we drive hinge screws generally after pre-drilling the hole.

[@user-jb5yy7ot5l]

Ilyen gyönyörű fát így tönkretenni egy közönséges asztalkáért???? Ez minden, csak nem megbecsülése a TERMÉSZETNEK

[@user-ou5el9xu7p]

Belle invention très beau, Bravo

[@culturemyworld2362]

I doubt those hinges are strong enough to support the stress. You need more support or it will at bow in the middle... or worse!

[@timmermankoos]

Het lijkt op het principe van een behangtafel. Niks creatief.

[@curtkuhns]

James Krenov would turn over in his grave! My major complaint about this video is that it is run at twice the normal speed, giving the impression that all this work is easy and one should not pay a lot for it. The best part of it all was the patience the builder demonstrated in milling down the pieces. The joinery is terrible and the use of metal staples or brads to hold the thing together while the glue dries is outrageous. Advice to the budding craftsman? Read a couple of James Krenov's books.😊

[@JohnDlugosz]

I'm sure that's why there is a ridiculous number of dowels -- it's not just decorative, but makes those joints strong enough, gap-filled as they are.

[@user-iw7yp2lw3i]

عامل ماهر وذكي ومبدع احسنت العمل مرحباً بك في الجزائر

[@johnhicks692]

That bandsaw blade was dull. Look at the burnt sawdust it was throwing out.

[@almario-im2yt]

Almost perfect step by step work process but one thing i npticed the craftsman forgot forgot to to apply glue to the rest of the hole ! My.grade for the entire video is 8!

[@bryan2523]

Great set of clips. Incredible , Thanks.

[@jeanpierrecharnay3662]

Bonjour, j’aime beaucoup vos vidéos, elles sont très jolies et très instructives, pourriez-vous me dire pourquoi vous mettez des morceaux de benenier que vous retirez ensuite ? Merci pour votre travail, très bonne journée.

[@JohnDlugosz]

What is "benenier"? I can't translate that word. The video creator probably doesn't know what you are asking, as well.

[@denisemurray412]

You caller them ugly boards. They have beautiful patterning.

[@judithfairchild8620]

Yes they do!!!!!!

[@johannsandl15]

Mich würde interessieren mit was der Tisch eingesprüht wurde.

[@hermanosudaca5006]

laidea no es mala, pero tiene una gran falla, las bisagras no tienen la suficiente fortaleza, ni tampoco la madera donde estan atornilladas, para resistir el peso que se pondra encima, cuando la mesa ya este desplegada, esa mesa colapsara con su uso, y sera frustante tanto trabajo, se puede mejorar ese proyecto, ..

[@JohnDlugosz]

Yea, and it will not stay flat as it will want to open until the opposite sides touch, while there should be a couple millimeters between them. I've seen folding tables that use a *lag bolt* that holds it while unfolded. The hinges don't have to carry those forces.

[@user-my4fq3wz9j]

Интересный столик, молодец!!!

[@user-tg5ke1ys1z]

очень много работы, толстезный, ножки толстые, как за ним сидеть, носить тяжолый. Даже не знаю. Зачем переведено столько материала. одним словои ерунда. Мастер вложил душу. Работа бссмысленная.

[@NarsiMan88]

Is AMAZING ❤❤❤❤❤❤

[@MASI_forging]

Amazing 👏👏

[@pavlegazibaric6493]

👍💪❤️❤️❤️👋

[@toumicarlos4037]

👍👍👍

[@paulmoran4907]

i couldn't watch that fully, I just skipped thru and cringed at every point, my biggest cringe was the using Pozi 2 screws with a Philips 2 bit and listening to the death rattle of the Phillips bit getting completely FUBAR along with the heads of the screws.

[@anrdaemon7115]

Handles too far from each other to be comfortable. Did not take furniture off before painting. Creativity 5. Implementation 3.

[@garydewitt8205]

Why didn’t he finish the inside? The table is not finished until the inside is finished!

[@gallowaylights]

Fabulous

[@user-fs7ez4yb8f]

Gluing technique?

[@lele-nz6xk]

Ok1

[@neilhfrancis1334]

Your lack of safety using the circular saw is appalling! You wouldn’t last a nano-second working like that in the UK - or in most advanced countries either. You are lucky you have all of your fingers. Next time you fancy getting your drilled holes to actually line up (instead of being all over the place) try pilot holes first.

[@user-fj1gs9ge6t]

Para que son los agujeros de costado.

[@rebasmirnov7507]

Recycling wat?!

[@AkkiSan23]

looool

[@Coole-ee1vg]

Why not slow down a bit and pay more attention to the finish???

[@marcotranchero3545]

grande spreco di tempo per un lavoro inutile, specie di pioli e le due maniglie, demenziale|||||

[@dreamgear]

Cobby

[@ShubGW]

Too long

[@accountaccount887]

吾够直象个沉腰猪要技术格面成一直线

[@JohnDlugosz]

This video could use a lot of summary editing. Cut out the boring parts! Rather than watching every minute of the sawing of the log, skim through it. When you do something 4 times, just show full detail the first time and skip over the repeats. I skipped over most of the dowel work -- I got the idea quickly.

[@user-zw4jd4wm8m]

Мне 58 лет. В юности меня учили, что склеиваемые поверности должны быть равномерно намазаны клеем. Тв же делаешь на херсоси. это брак. не приятно смотреть.

[@JohnDlugosz]

I feel the same way: the miter joints should have been planed flat and fitted nicely. The top _could_ join to the sides without any gaps. That's why he has such a large number of dowels: these hold the joints together, strong. Or they should if the glue coated the dowel! Just dropping glue into each hole I think it must just fall though. Or, could have used an adhesive that's good at filling gaps, like certain kinds of construction adhesive. But, having learned the same as you, I did some experiments and found that a lap joint with glued surfaces in all three directions, crudely made with a saw and not planed, then dried without proper clamping pressure, was still strong enough that the failure was twisting the wood apart, not the glue line. Makes me wonder if the advise and dire warnings were derived from use of hide glue and original PVA (white) glue, and modern modified PVA (yellow woodworker's glue) might be far better. Glue certainly needs to be spread though! Just because there was some squeeze out in one end doesn't mean that there isn't dry areas in the joint.

[@user-willow9386]

이해 불가다.

[@lindaotley]

Nice very unique 🫶

[@threestarfancywoodworks1902]

youtube.com/@threestarfancywoodworks1902?si=PSy5Bdqeo2EI2uKR

[@thomasklughammer6586]

that is not recycling

[@DraganDragnev]

На плота едната дъска неправилно сложена! А иначе е супер!

[@Puymouret]

good example of how NOT to do things

[@rodrigodiez3047]

Qué desperdicio de tiempo y de madera

[@1meanelf]

Not everyone has good taste and your comment just proved that.😊

[@jeanpeeters5450]

what a bad idea, way too expensive, way too heavy, way too clumsy for what it is

[@GilbertoCalderonsantacruz]

😮😮😮😮❤

[@BrantAerials]

No accounting for wood movement with crossgrain glue ups. (Fail)

[@williamsondelimasantos2139]

I totaly agree.

[@yahayamfinanga2169]

🤏👌

[@MegaDivertisment]

I don't understand what is the use of this table! ...based on the thickness of the board you used, I think it weighs 30 kg, so it's not portable...you ruined the material for nothing...besides that, yehnica leaves a lot to be desired!💩💩💩💩💩💩💩

[@albertbickel]

I also think so

[@user-sz7qb4jg5w]

быстро быстро быстро скорей скорей нас много много тяп ляп тяп ляп сикось накось халтура китайская

[@MAKSAVELLO]

Зато замки и ручки залачены ...вах-вах,красота...🤗😋🤪

[@conica68]

Vaya cosa fea