SMITH & WESSON REVOLVER INTERNAL LUBRICATION

[@richardflaherty2373]

I don't own a revolver but after watching your informative video, I am going to buy one just to take it apart and lube it like you did.

[@howardkahn4330]

JERK

[@rayb9053]

Awesome video! Extremely helpful, clear, and concise. I have many semi-automatics, but I am a newbie on revolvers. Thanks so much!

[@howardkahn4330]

MORON

[@rodcoulter997]

Great camera …great instruction….best I’ve ever seen on SW revolver. U make look very easy.

[@rman8853]

Wow! I can't thank you enough. This is so helpful to many of us.

[@howardkahn4330]

BULLSHIT

[@solarflare1008]

I can not believe that a revolver has more springs than a semiautomatic pistol. Great video.

[@howardkahn4330]

ANOTHER NITNAT

[@BillRopke]

I just used your tutorial on my Dad's 1965 Model 17 K22 Masterpiece. It was really stiff when i used it last weekend. It was purchased new by his Dad as a high school graduation gift. Oh my gosh, is this revolver smooth again. I asked him if he had ever had it serviced or ever had its sideplate off. He said he took the plate off once, looked at it, and was afraid to take it apart any further for fear of messing it up, so he put it back and never touched those screws again. Thank you so much for the step by step instructions.

[@CreasyEQ]

This is fascinating. I could watch this video 100 times. And I still wouldnt take it apart like this alone. But it's nice to see what makes guns go BOOM When the trigger is pulled.

[@WheelgunsOnWheels]

Taking them apart is actually quite simple, it’s the putting it back together part that’s nearly impossible.

[@howardkahn4330]

@@WheelgunsOnWheels FOR SURE

[@user-nk1yu9cw8o]

Just had to replace that tiny spring on my “cylinder stop” (S&W “Model 603”) and man you were correct that was not easy to get back into place. The original factory finally wore out (1981 S/N) and the original “cylinder stop” had developed an odd burr on the lip of the hole the spring sits in. Pistol was not functioning correctly in DA mode (misfiring every 10-12 rounds) but was fine is SA. Clearly this created a timing issue due to the tension on the “cylinder stop” not being within ideal spec. I opted for “factory new” & “remove & replace”. Lubed & oiled and it’s back up to 100% functional! Excellent tutorial!

[@pekolucky]

Terrific video! I may even break my revolver down! You've given my courage! Many thanks!

[@Dwyer88]

Great video sir just getting into revolver world. I’ve got a 686-P & 629-6. Have few others but those Smiths are my latest! Love how you go slow and in depth. Nice that you talk to us and not down at us as if we are dumb 😂. Thanks again sir

[@cantdance3077]

The only video I've seen that makes me think that I can do some of this myself. Particularly appreciate the tip on using lighter fluid instead of a complete teardown. Subscribed cuz of this video.

[@azvoltmanphoenix446]

This is my go to video for a couple years now, thanks !!

[@tj4070]

This was excellent, thank you. I inheritied a S&W mod 64-3 38spl and this helps tremendously.

[@stevestone5671]

Today I picked up my S&W 586. Thanks for the helpful video. Subscribed.

[@marktracht7782]

Thanks for your great video, gives me the confidence to get in there and do a thorough job.

[@jayfortier2473]

Very detailed and has encouraged me to attempt this procedure on all my wheel guns . Well done and thank you!

[@QuietMikeW]

Your narration is so soothing, like Bob Ross lol Great video

[@marktracht7782]

So, using this video and your Wolff springs video I was able to update my 617-6 with a Wolff spring kit and thoroughly clean and lube it. Couldn't have done it without you, thanks. In this video you mentioned some places that you had polished. Hoping you would comment or even do a video on how and what to polish to smooth things out. Wish Wolff would include the set screw. I went to 3 stores before I found the right one.

[@travisjohnson9432]

I have a 686, I don't know if I want to go through all of that to clean and lubricant my 686.Thanks for the tip on using lighter fluid and other lubricant/cleaning spray to lubricant the parts without taking everything apart. But great video on how to take the 686 apart to lubricant it!

[@normanmallory2055]

Brake Clean is a good product and I use it for spray cleaning metal parts /components ! It dries very quickly and leaves no residue!

[@RickyJr46]

That's a mighty fine tutorial! I'll try this on a Model 36 J-Frame.

[@RickyJr46]

This simple lubrication done on a Model 36 J-frame reduced its DA release from 13.5 to 11.7#, with a much smoother action. Amazing!

[@johnreacher3756]

I would like to add some advice to this video. Before you remove the sideplate, back off the strain screw from the mainspring. When the sideplate is on, those pivot posts, especially the hammer pivot post, is supported from two sides, the frame side and the sideplate side. With the sideplate removed, all of that tension provided by the mainspring is held on that pivot post from only one side. It is possible to bend the post or even break it off of the frame. A very small amount of tension is all you need to hold the parts together and to function test (and see) the action with the sideplate off. I sort of cringe when I see a part being pried off from the frame. If you jam a screwdriver between the rebound block (or slide) and the frame, you can gouge scratches into either or both parts. Brownells sells a nice tool that compresses that strong spring to let you gently lift up the rebound block. As long as you have the rebound block out of the frame, you can replace that spring with one with a lower compression strength. Buy a few extra springs as I guarantee that you will eventually launch one into the deepest darkest corner of your room. Otherwise, a very nice presentation.

[@colt5189]

Where's that "link" to the video you said you'd put in the description?

[@TheJennflip]

I use a larger Phillips and the post fits pretty good in the "groove" and push and push down with the other hand until the spring catches on the post and then push it on down with a small flat screwdriver...

[@flinch9748]

Thanks for the vid. But please get yourself a specialty tool for de/installing the trigger rebound slide. It makes your life so much easier. (And looks really professional)

[@jeffriley-lq5np]

i made mine out of a junk screwdriver. a couple minutes of dremel and file work

[@SpikeGlock21]

Bic pen works perfectly!

[@brianblackburn-author7531]

Damn! You're a surgeon, brother!

[@mccannfamily...7652]

Thank you. I have a 686 Plus. I am getting ready to install replacement trigger bar & striker pin / springs from TKC and I want to take it “all the way down”. I’m no expert but a 40 year aircraft turbine tech and I have a pretty good gunsmith area set up. A was considering using Otis dry lube back here or even dry graphite spray grease on certain friction points. 12:25 Would love your input on that please. Thanks again; your video is now my “official” “how to” video. Wish me luck but please reply with suggestions & comments. Thanks… Gene

[@sgharpsr]

Thanks a bunch! Very well done.

[@Satierical]

great video im sure ill watch it every time i clean 686

[@TheJennflip]

Yes I was going to mention the phillips head screwdriver--the "channel" in the bit allows it to go over the post---it will at least catch the post then I use a small screwdriver to push the spring on down...

[@diacamp8595]

Great video for information 👍🏿

[@donannis6983]

Excellent!

[@bostitchmaloney9394]

You could mention to people not to remove the hand from the trigger. You did not do it in the vid but people should know that if you do there's a tiny torsion spring inside the trigger that applies pressure to the hand that's a real PITA to get back in place correctly.

[@richardevans3084]

I took out that same spring also ; Holy Smoke it took a lot of cussing and sweating getting it back in It’s not coming out again 😂😂

[@vandechu]

Great video man! Thank you

[@montecraig7032]

I have a Colt SAA that I have fired 15,000 rounds through over 44 years and have never taking the grips off.

[@richardevans3084]

Great tutorial video big thumbs up ,Question; is it okay to use Brake Fluid to clean inside of Gun

[@arnenelson4495]

Yes, but all surfaces must be oiled lightly because it leaves the metal dry.

[@LoreFoundry]

I learned. Thank you.

[@michael5619]

A few tiny drops of oil or clp in actionable parts would suffice, work the action a bit and let it do it's job. Any use thereafter will help keep the parts moving and well lubed without gunking up the works.

[@carlbrooks68]

Can you please share some information on this firearm. I jus purchased a older 38 special s/w 67-6 . It also has the Floating firing pin . I am Seeking information and You Kinda look like your up on your Game . Thank you . carl

[@alfredocuomo1546]

FYI If it's a Smith & Wesson it's a "Yoke" if it's almost any other revolver it's a Crane. That's if we are using the correct Nomenclature. LMFIAO Best part about a wheel gun is it's hard for the lubricants to attract any carbon unlike a Semi-auto pistol. Also if you run out of cartridges you can always use it as a club, can't do that with Polymer guns.

[@steveellison2171]

Thanks for video!🤘

[@lens7859]

where is that link you were talking about, another take apart video? Nice job, I have started to do the same with my guns. Love to see how they work and clean em up a little.

[@Spotinski]

Trev. from Australia, what thread type and length is the Allen screw your used to replace the main spring screw?

[@R0b87]

It's an 8-32" set screw. I use a 1/2" length one in mine.

[@pmwheatley]

After cleaning, could you just spray in some Rem Oil or dry lube?

[@freeandcriticalthinker4431]

What a great video! Let me ask you, i am assuming you have slicked up your gun yourself. If so, what material do you use for that? I would guess that it’s something like varying grades of Diamond sandpaper and/or paste? Just curious on what you prefer . Thanks so much

[@jonpaulison2283]

Great video thanks

[@AviMus82]

The gun needs to be broken down that far just to be lubricated?

[@cole4406]

Not a Glock haha. Only needs to be done every several years for most people. Maybe once a year if you’re shooting a ton.

[@JeffPR16]

useful! thanks!

[@mccannfamily...7652]

Hi again… I don’t see a link to the video you mention. Am I missing something. When I go in to do the TKC mods; besides cleaning; I plan to use a low speed battery dremel and some buffing attachments & Flitz and polish every thing up. Again… Hope you’re still out there; read this and send feedback. Thanks again… Gene

[@shermanhouse6880]

Hello, Jean. Before you do anything go to Gun Blue 490 watch his video on Smith and Wesson revolvers. Old school dude went to Smith and Wesson factory school. Might save you some grief.Good luck good look and god bless

[@pmyoo8861]

Thank you!

[@davidditoppa5043]

I have a model 67-1 sometimes the cylinder seems to stick. Do you think that is a cleaning issue?

[@bertkilborne6464]

Newly subbed - Thanks for the video - I just put a deposit on a 686, last week One Question *:* Do all recently manufactured 686s have the round butt grip ?

[@moviebuff1853]

I own a pachmayr grip for the k and L frame for the round butt . I bought it with the 686 plus as of last year .

[@nickr3589]

Is it normal to have scratches in the cylinder I just bought one and noticed there’s marks from the cylinder rotating is that ok?

[@chetmakowski463]

Wow! Thanks so much!

[@totljag1]

I have a question, just purchased a new old stock 586 no dash new in the box , from sitting for so many years do u think this need to be done ?

[@cesarmuniz5158]

What screw drivers did you get?

[@cesarmuniz5158]

Thanks

[@TrailBoss1860]

I wonder how many people are gonna have to take their revolver to someone to put it back together after watching your video that would be interesting

[@steveandrushko75]

Take it down way more than I would ever attempt to

[@paulmarion7578]

How often should a revolver be cleaned like this ?

[@stephanpetranker8994]

About 500 rounds I feel a difference when using oil…have to try grease. Oil is slicker initially….but does last as long. Use synthetic for cold, or if you are going to store for a while. Petroleum grease will get gummy over time. I switched to synthetic as my everyday…

[@scvdeputy]

Out of curiosity how close is this video to a S&W 66 in parts and their location if attempting the same objective?

[@jtdundee]

Aside from the slightly different sides of the hammer and the new lock hole (neither make a difference for cleaning) its pretty much the same thing. You can do it, watch the MannyCA video also.

[@jeffriley-lq5np]

virtually identical

[@274152]

Revolver should not need grease all over sides of hammer or trigger. Both are made to "float" on raised pads on their studs. Small amount of grease on these bearing pads OK. If there are wear/scuff marks on hammer or trigger from rubbing on frame and side plate, you need to dress the places that are rubbing and may want to put in sideplate bearing shims.

[@WheelgunsOnWheels]

All those springs! You make this look about 6,000 times easier than it actually is.

[@steveedington5231]

Its your revolver my friend but myself ZI would make sure the hammer safety was installed not finding fault just trying to be safe

[@cleger617]

70x more lube than you need, Cletus.

[@arnenelson4495]

Yoke on S&W, crane on Colt.

[@larrymoody7207]

There is a tool designed to remove and insert the rebount spring.

[@TrailBoss1860]

Why don’t you keep the block in

[@Ray74020]

Why remove the transfer bar? I’m only asking for education purposes I’ve never heard of that being done.

[@frankbutta9344]

It’s actually a hammer block, and serves to prevent accidental discharges when the gun is dropped. Removing it is dangerous and irresponsible.

[@arnenelson4495]

Some target shooters feel that it causes (slightly) more drag and the gun works smoother without it. It's the secondary hammer block not the primary one so theres still protection.

[@Ray74020]

@@arnenelson4495 Thank you. I didn’t realize.

[@rodcoulter997]

586-1 ..why does my cylinder move way too far reward out of alignment when I push the Ejector rod. Like 1/2-3/4 too far back..have to “Snap it” forward to get it back in alignment to close…..you look like would know. Bad cylinder? Bad yoke journal…my 36 and 64 never have done this…had the cylinder out and completely apart..cleaned and Ballistol…..no help.

[@slotcarfan]

I had to cock the pistol before the side plate would drop in. I have a newer version 686 with the infamous lock. Maybe that was the difference.

[@schutendohkji548]

Thx for this video. I just subscribed. I'm same w 'Can't Dance' below. WD-40 maybe another watery semi-lubricant to spray out the dirt from the non-removed innards. I don't know which wld b better, Ransom or WD-40 but worth an experiment, find how smooth the trigger-hammer operation is. I'm wondering if ur Stainless (or Nickle?) revolver has the MIM innards as u have that Hilary Hole. Are the innards stainless too (use a magnet)? If so, dat'll b great as they won't rust n shouldn't b needing frequent clean up for a wheel gun vs. automatics w un-burnt powder messing up the innards. Hey, let the TopperWear plastic gun lovers enjoy plastic innards too, no lube, no rust? But he still need to get rid of the powder unlike the wheel gun?

[@michaelw.5921]

Could you just hit that with some brake cleaner, throw some lube in there and be done? The disassembly looks tough

[@kbm-zw5jd]

No. I shot some break cleaner into the internals before I felt like taking it down. It leaves a film. Taking it down isn’t hard and is educational. I’ve torn down every revolver I have ever owned and that’s more than 2 dozen. After a few times it’s very easy.

[@Freedmevr45]

Not a good idea when you live in a state where temperatures get below zero in winter. Oil and grease will freeze and lock your gun up. Leave it alone

[@stephanpetranker8994]

Use synthetic lube in cold….i use graphite in hot sandy places

[@jtmo3]

Way too much grease and oil. There’s a reason these revolver come from the factory mostly dry inside.

[@AtomicDogg0213]

Why? Serious question.

[@jtmo3]

@@AtomicDogg0213 Most parts are hardened. And not subject to excess movement stresses. Wipe a small amount of oil on parts, then wipe away, leaving a microscopic layer. All the protection you need. You will not wear a hardened part out from normal use in a lifetime. All excess oil will do is attract crud, then you will have a paste mess.

[@boricuaarecibo9259]

I broke down my 686 and my 629 like this and used a very light coating of mineral oil to protect from rust

[@brianmorg]

Agree, I’ve never broken my 686 down this far. In fact, I was warned against over-lubricating it when I bought it for the same reason mentioned here.

[@Mowkade]

I always love it when guys complain about too much oil or grease, equally as stupid ass complaining about a woman being too wet. Having watched this video from beginning to end at no point in time to be overly grease or oil anything. I’m guessing you jack it dry

[@waynehajek6346]

Where's the missing link?

[@denniskennedy3311]

You don't have to go that far

[@AviMus82]

You mention proper screw drivers, but don’t tell us which one it is?

[@howardkahn4330]

He says DO NOT USE WD-40, that must be because this may loossen up parts from being secured, i do not know other than the fact this substance does not last, anyway i do not take any hand gun apart, i look for an opening in the gun to blow out any loose dirt,then i drown the gun in oil and either blow the excess out or let lt drip dry, than wipe the outer parts dry........YOU HAVE TO BE NUTS TO TAKE A REVOLVER APART OR BE A GUN SMITH....I have had revolvers the past 60 years and have never taken any of them apart....IF IT WORKS ,DO NOT FIX IT !......STUPID VIDEO, anyone who follows this guys advice is just looking for problems, and that's a fact....

[@J0HnNySands1]

scam...you dont need any special lube for your gun

[@Thesusoperator]

Do you put oil on the cylinder release mechanisms?

[@geezerp1982]

do you this strip down and lubrication yearly or something??