SNNC 571 P2 Tractor Radiator Cap (using the dividing head)

[@64Pete]

As a rider, I appreciate thoughtfulness at the end there John, and I am sorry for your loss. Happy birthday Rob. 🤙 🇦🇺 ✌️

[@kevwelsh7209]

Fantastic series of videos 😊 just picked up a Colchester Student lathe recently and getting myself back into turning after a break of 28yrs when I used to do it for a job! Your videos help me remember what to do , keep up the good work 😊

[@BensWorkshop]

Good work John. May Rob's soul rest in peace 🙏

[@jimallen9442]

I heare you John, two crushed vertebrae from a driver who never looked, 38 years of pain, but at least I'm here to talk about it. Sorry for your loss.

[@djhscorp]

49 years motor cycling. 2 accidents, both caused by drivers pulling out in front of me. Still going strong at 68. Ride safe all.

[@retromechanicalengineer]

So sorry about your brother John. I've cut my road riding down as the risks were getting too high. It just dawned on me that I've been watching your channel for 12 years!

[@johnoregan8245]

HI John, If you place an old paint brush down on top of the lathe tool point when cutting brass it stops the swarf flying everwhere, Ok it does not look so good on camera but it makes cleaning up a lot easier. Good advice Think Bike!!

[@markj8068]

superb job there John, always 'think bike' as its those left behind that suffer the most RIP your brother,

[@bobdixon6060]

A job well dun

[@sidecarbod1441]

A wire wheel in a bench grinder is a great way of softening off all those sharp looking machined edges, it will 'age' the part nicely.

[@richardbrobeck2384]

Love the latest build !

[@dennythomas8887]

Happy birthday to your brother John. Nice work on the cap.

[@dannygreene4594]

That is a bloody nice job.. very tidy, you should be pleased with that..

[@georgeton4991]

Great work gaffa.

[@kentuckytrapper780]

Great video John, keep'um coming..

[@graveneyshipright]

Thanks for your time in these really good projects. Why do I think one day there will be a roller parked on the drive and not the Royce type..... happy new year to you and yours.

[@Quignal]

I totally agree with you I was hit by a Volvo on the main road he was coming out of side turning fractured Pelvis and amputated thumb and all because Lt Comamder Haythornethwaite (RN) did not look 49 Years ago!

[@adven999]

Nice result.... It might have been a nice little pattern making and casting project..?

[@paulp96275]

Great work John fantastic God Bless at this sad time 👍

[@bostedtap8399]

Certainly not a job for the faint-hearted John, nicely done, messy stuff machining brass though. Good idea on milling the scallops before parting off. My thoughts to you, and your family on Robs birthday.

[@paulmorrey4298]

Thanks John

[@djhscorp]

Looking good John. Thanks for sharing your thoughts on " think bike" .

[@RalfyCustoms]

Happy days John, wondered how you would finish this? Have something similar coming up myself, thanks for sharing and so sorry for your loss man, I've rode bikes 40 yrs and lost a few along the way ❤

[@thomaswilliams]

Thanks John.

[@BedsitBob]

I see you put a little witness mark on your chuck jaws. 😥

[@RockerMark]

The fuel cap is looking good John. A real shame your brother was taken because of a car driver. I ride motor cycles and have encountered plenty of Stevie Wonders on my journeys.

[@Oldsmob455]

How big/inches is that rotary table?

[@marley589]

Were you asked to make it in two pieces? Turn the whole thing then part off and add the notches.

[@doubleboost]

I was just asked to make one .Up to me how I did it . I have made smaller ones before using this method

[@marswalkerpilot2303]

67 here and still riding my ZXR750 h2 but going to a sit up and beg enduro bike for this year and the only real close 2 i had on a bike were 2 idiot volvo drivers who didnt see 2 blazing head lights from me and still pulled out of a side road to cross a dual carriage way that was restricted to 40 mph. Volvo drivers thing they are invincible i think.

[@ЖелезнаяЖизнь]

Можно было и быстро режущей фрезой сделать эти сегменты, просто нужно было врезаться сверху вних, как при сверлении.

[@SepticWhelk]

Tin can folks do THINK BIKE they think he will get out of MY way, they think IT'S MY ROAD !