√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*
@am.ahmedd3 жыл бұрын
Save us, good people my husband and I have three children orphans needed to help him To continue and the number is present in the personal image of the KZbin channel
@Gasdoc063 ай бұрын
Appreciate the tear down of the master cylinder to explain the leaking seals, but why didn't you explain the installation of the new one?
@mr.selfdestruct16773 жыл бұрын
The quality of the videos are getting better and better, I love the breakdowns how a part works and the camera angles great work.
@InfamousDogPound3 жыл бұрын
Another great video buddy. Why you dont have MILLIONS and Millions of views on this I have no clue. Keep up the great work. Thanks for your help.
@deespasojevic30133 жыл бұрын
Oh yea my man Len is back at it again! Nice work bruddah
@dpaulak3 жыл бұрын
There is a Primary Piston and Secondary Piston in that master, if that master is leaking in booster the fluid is going to be suck in the engine via the booster hose..check inside of booster hose.
@garyrohlman60132 жыл бұрын
THIS GUY IS ENTERTAINING. VERY GOOD TECH. GREAT TEACHER
@floridamanfishing13902 жыл бұрын
Great video sir The breakdown definitely gonna help me out with my vehicle I am having the same issue as you were also i have a question for u you did not show bench bleeding the brake master cylinder did u need to do that or was it not needed ?
@onyxtraveler3 жыл бұрын
I’m having the Same issue but can’t find a fluid leak anywhere :/
@johngreek57883 жыл бұрын
It would have been nice if you would have talked about bench bleeding it. Good video. Thanks
@GMoney-B2 жыл бұрын
I am no expert so take this with a phat grain of salt, but I would think with a pressure bleeder that you might not need to bench bleed since it forces all the air through. Tthat is what it does with regular bleeding of the system but I don't know for sure though.
@getminesallday242 жыл бұрын
You can bleed it on the car just loosen lines up and push brake till no air comes out attach lines back uo bleed all 4 calipers
@dashkamcarma1221 Жыл бұрын
Gotta love Len.
@Dhi-fe5eu3 жыл бұрын
Great video. I love watching and learning from 1A auto. Keep up the great work.
@jstncheney Жыл бұрын
That thumbnail image is priceless.
@mx20483 жыл бұрын
Scotty, Chris, and others recommend using flare wrenches to unscrew the nuts from brake cylinders. Flare wrenches hold 5 sides of a nut, whereas regular wrenches hold 2 sides only. You did use flare wrenches too. Just noticed.
@brianschrier61932 жыл бұрын
Enough with the cutaways and more with the info. Thanks for being thorough & talking fast. Good job.
@sirenswhispering4 ай бұрын
i bought a new jegs brake booster and master cylinder, i renew all the hoses, drums, and pads with lines, and there is no any leaking, my engine is 4.3 stock with holley sniper 1. I wonder why it happened sometimes, for example i drove about 45 min without any problem, when i wanted to park my car, suddenly i lose a brake and become stiff and immediately i push it again came back to normal. I did all of your test and could not find problems, as i said sometimes it will happen.
@jayflow233 жыл бұрын
You are the man brother.
@1AAuto3 жыл бұрын
+Jayflow23 Entertainment Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@jayflow233 жыл бұрын
I always do .💪🏾💪🏾💪🏾💪🏾💪🏾
@kshipon17982 жыл бұрын
My 07 Lexus RX 350 break padel sink, (not all the time and not everyday) master cylinder has been charged twice problem still exists, has been bleeded couple of time, everything else is good, no leak anywhere why do you think it’s happening? Thanks
@bigwon4056 Жыл бұрын
I’m having the same problem but I haven’t got a leak and have bleed the brakes,iv tested the servo and it good, so now I’m thinking it’s the master cylinder.? My brake pedal sinks to the floor when engine it on, and it’s like you have to pump the brakes to get a hard brake.? Any information would be great
@kanevivalakane3699 Жыл бұрын
Hi. I am sensing some issues with my brake pedal. Let's say I am driving on highway and not using brake pedal for 15 mins. I have noticed that to apply brakes, it needs a little hard foot. It becomes scary at times. However in city driving like stop n go driving the brake pedal works very good. What could be the issue?
@jeffdoughty12569 күн бұрын
Thanks for all the info! You may want to ease off on the Red Bulls though. 😂
@crazychivez3 жыл бұрын
Super informative! Thank you guys for this video
@1AAuto3 жыл бұрын
+Luxor Slopski Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@TMM69003 жыл бұрын
Seal failed due to contamination? Oil or old brake fluid?
@latafairam2 ай бұрын
My brake pedal sinks to the floor. I plugged the cylinder. feels solid/stiff. Doesnt sink while pressing. So my master is good. I've bled the system like 4 times. have gone thru 5 big bottles of fluid. I have a non-abs 2004 camry. No leaks, etc unsure what to do at this point
@johnjkizer6399 Жыл бұрын
Great video, thanks My question is when flushing the brake fluid from my friends car I cannot get fluid to come out of any of the 4 wheels, if it was only one wheel that wasn’t bleeding I know that it would be likely a bad caliper but on all four wheels, could it be the abs unit that giving problems or master brake cyclinder. Thanks
@Nicedesk2 ай бұрын
Excellent video and info, thank you!!
@killdano Жыл бұрын
Wow you're a rly good actor
@bgizzle75452 жыл бұрын
My master cylinder is about 3 months old. I went to leave work a few days ago and when I pushed the brakes the pedal went to the floor and stayed. I can't figure out what it could be. I can't find any leaks anywhere
@temle74894 ай бұрын
Hey A1, can u reuse the old reservoir and put it in the new master cylinder?
@juanulloa53382 жыл бұрын
How are you i need to know How do you remove Wire connector from the Master brake Booster pls
@karlie-raezirk37011 ай бұрын
Only been dealing with this for 2 years. Neat
@Nickthecarguy3 жыл бұрын
Where can I get the kit to bleed the master cylinder
@kevinmanning48802 жыл бұрын
Find another master cylinder on a vehicle at the auto Wreckers. Remove the fittings , cut the lines, long enough to bend the lines to sit in the reservoir to submerge under the fluid level to bleed the master cylinder. If buying over the counter, it should come with bleeder kit.
@johnnybonifacia91772 жыл бұрын
What about the fuel that leak in to the booster....you have to remove it and how.......what happens if the engine suck the fuel in the intake valve
@miguelgomez8933 жыл бұрын
Great video 💪🏻🔥
@1AAuto3 жыл бұрын
+Miguel Gomez Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@ChiraqVet Жыл бұрын
I just replaced the passenger side entire hub assembly, caliper, rotor, break line, when that obviously wasn't the problem. My passenger side break froze to the rotor causing a fire. 2009 Silverado. Yup i need a master cylinder
@marcsongaudin84293 жыл бұрын
Great people 1aauto guys
@musclekingmedia7 ай бұрын
8:00 not true. If you loose brake fluid in one side of reservoir, the pedal will still sink. The air from one side will get into the other.. air can get past the MC piston seal. A true safety measure is dual master cyl. The only way to keep both separated.
@SamVieiraGuitar2 жыл бұрын
Hey guys, it would mean a lot if you could help me with a question. So I have a soft pedal and one of two things, master c. or air in the system. My car has hill assist and when the brakes lock up it is the abs doing the job right? In that moment if my master cylinder had an internal leakage my pedal would still be soft because its the same as blocking the master c. outputs right? BUT, when hill assist is activated my brake pedal is rock solid meaning my master C. has no internal leakage and the problem could potentially be air in the system am I thinking right? Another thing, I bleed all 4 wheels but the pedal is still soft, could the abs module itself need bleeding? I see on youtube people bleeding the abs module for that reason. Please tell me if im thinking right. Thank you
@fito69503 жыл бұрын
veey underrared channel, Keep it up ! :)
@1AAuto3 жыл бұрын
+iGambled Thanks for the kind words!
@marqueswilsonn Жыл бұрын
What if there’s a stream of fluid squirting straight upon the reservoir
@1AAuto Жыл бұрын
+Marques Wilson We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@marcrobert76903 жыл бұрын
The best brakes I know of are the titanium calipers on the Bugatti Chiron Super Sport.
@janielramirez91813 жыл бұрын
U can replace the seals nt the master cylinder
@teddylundgren3984 Жыл бұрын
I'm 99% sure you only pulled out half of the stuff in the mc as in only the primary circuit piston and spring, I'm pretty sure there should have been another thing and another spring
@louvendran72733 жыл бұрын
The rust! It's crazy to live in the rust belt.
@edwardacosta4429 Жыл бұрын
This is going to help so much bro hy
@richk3202 жыл бұрын
Great video!
@lockhamj10 ай бұрын
Great vid,
@vontrap6942 Жыл бұрын
You need to 1. Stop doing acting scenarios you can't act. 2. Just do the install, we don't need a scenario and a story behind it.
@joebagofdoe4762 Жыл бұрын
He should start his own show for himself He could be another Scotty Kilmer!!!
@HomeMadeBoards3 жыл бұрын
Can't tell if you cause my issues or know them personally. The exact video I need the day my issue arises! 🤣
@1AAuto3 жыл бұрын
+Jesse Turner Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
@romancastro32533 жыл бұрын
Replace Master Cylinder and Booster. Attempt to fix this rusty crap will come back to haunt you later just when you need them the most. Go new on the Master Cylinder, do not trust remanufactured parts.
@woodandtable2 жыл бұрын
You skipped bench priming the new MC.
@samueladjavon48252 жыл бұрын
nice job, you really know what you are doing
@billbixby787711 ай бұрын
My brake lines have a leak and I am still driving it.
@sanfordader2 жыл бұрын
Why didn't you show, or at least mention that you bench bled the master cylinder? Trying to bleed a system with an empty master cylinder is infuriating
@panayiotiskrokodeilos59352 жыл бұрын
In this video he sounds like Chris fix doesn't he?
@danielsegovia8113 жыл бұрын
Very helpful video! I'm gathering information on how to replace master cylinder!
@林华春红2 жыл бұрын
oh no!!!!
@geniuscommentalert93763 жыл бұрын
1
@sifusays92422 жыл бұрын
What I get from this Video is the company you work for doesn't pay you enough money to buy a better truck .U have communication skills get paid for it .
@rebeccagray9863 жыл бұрын
PLEASE - SLOW DOWN!! I'm an old lady that needs time to process what you are trying to say.
@spinnetti6 ай бұрын
I've seen 80 year old cars in better shape. gross!
@am.ahmedd3 жыл бұрын
Save us, good people my husband and I have three children orphans needed to help him To continue and the number is present in the personal image of the KZbin channel