Soil Moisture Sensor with Arduino Uno

[@bennythomas8371]

Can you show how to connect the lcd without the 12C Module

[@anandanat]

Bro idha plants watering pandra maari set pandradhu eppudi bro

[@passiontechklm]

Watch this link bro ...kzbin.info/www/bejne/bXzHmX-VnKakfrM

[@KateMarcelo-q7m]

hi, what library did you use to write down something in the lcd I2C? i really need help for my project 😭

[@KateMarcelo-q7m]

the arduino ide says error baud rate

[@HoXDipannew]

Outstanding and interesting video bro

[@SwastikaAbrol]

Hi could you please provide the list of materials needed

[@OdongoJoachim]

my lcd just lighting not displaying text, how can i solve it because everything seems well from the serial monitor

[@passiontechklm]

its often happen when i2c code is not same or wire connection is not connet properly.

[@marthaconstanzadazatorres2500]

Thank you

[@lyde_c6237]

What to do if i am not using the LCD, is the code need to rework isn't?

[@passiontechklm]

@@lyde_c6237 if you dont use LCD than fine.No need to change anything .It will work .

[@sharriiiq]

Very nice idea i love it

[@adamriza7436]

can you show how to connect it to water pump?

[@passiontechklm]

kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@passiontechklm]

I have made more details video here kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@festivedarnspahs5676]

would this setup work alongside either an LED or a speaker/buzzer for visual and/or audible alarms for when your soil needs watering?

[@viastudios1]

mY LDC is not working. Which Library did you use?

[@dechaalsanabila7548]

can you explain the working procedure of the video above

[@passiontechklm]

@@dechaalsanabila7548 For over roll is the water pump will be on (Relay) when the soil moisture is low as a centain level as in code and will be off (Relay) when soil moisture level is high.This is the concept for this project .I hope it will help some how.

[@dechaalsanabila7548]

​@@passiontechklminstallation procedure? list the steps

[@dechaalsanabila7548]

​@@passiontechklmplease help me, sort the work procedures and design steps from the video above

[@bhartipatel952]

Can we use capacitive instead of this resistance which u have shown in video...

[@passiontechklm]

Mean capacitive soil moisture sensor? yes you can use also.

[@bhartipatel952]

@@passiontechklm ok.. thanku

[@heykeliglesias2639]

I just wonder with that load how you didn't break the Arduino board

[@passiontechklm]

@@heykeliglesias2639 It would burn Arduino because the load is from Relay out put so it really safe to use.

[@ΓιώργοςΜπαμπζελης]

Thank you very much but i think you meant analog 4and 5 because for me it worked on analog.

[@jkkk5377]

Hey I am trying to do this project but there is an error in the code given did you change it or something??? Can you please share the information It would be really helpful

[@ΓιώργοςΜπαμπζελης]

Hello there, just change the 2 pins of the lcd and put them to analog4 and 5

[@passiontechklm]

I have made more details video here kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@user-antim]

i have made the same circuit but lcd gets on but nothing is displayed.. only light is coming...

[@passiontechklm]

I have made more details video here, kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=tR170tS8z_b_q8zF

[@shirishakothuri1454]

can i use two channel relay instead of one channel relay????

[@passiontechklm]

Yes you can use,you just need to connect to in 1 only no need change the code

[@shirishakothuri1454]

thank you @@passiontechklm

[@CoolTunes-bg5pv]

Hi there, it's a good tutorial . Can you share the library you used

[@passiontechklm]

I have made more details video here kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@vivekentertenment]

Hi not working code

[@Animite.ka.channel]

Upload mai error hai eassa bolo na not working bolke disappoint kyu karte ho 😢

[@11thwala7]

Bro can you provide me data set of soil moisture capacity 😊

[@sitiumairah612]

Hi may i know do you have cooding this project combain with mqtt iot

[@InfoSphere_24]

Bro from where we can buy this components?can u share the website details

[@passiontechklm]

Hi Bro, You can buy in any online shop this items are just common parts.

[@Nishu-e7i]

what will be the cost for this project

[@passiontechklm]

@@Nishu-e7i Thats will be depends on where you purchase the cost will different

[@TheSilverwolf97]

I've got an issue with the LCD screen, in the video you say to connect to the digital pins D4 and D5 but you connect them to the analog pins A4 and A5, while also on the code the pin 2 is set so which is it ?

[@passiontechklm]

I have made more details video here kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@opallajoshuapith5303]

Do you have schematic diagram for this?

[@passiontechklm]

@@opallajoshuapith5303 i have made more details video here. kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=qxJUDWtvF6J4tVxK

[@dalesymes9677]

fix for relay contact chatter? Pump motor probably wont like start/stopping at that pace

[@passiontechklm]

kzbin.info/www/bejne/bXzHmX-VnKakfrM

[@batuchralerdenebat]

I LOVE UR CODE muah muah

[@sureshkt551]

Can we use node instead of an Arduino

[@passiontechklm]

Yes you can....but you need to change the pin follow up to Node MCU digital pin

[@madhavigade-t5w]

Can you please give the list of components used for this project in detail??

[@manchusinthu1270]

Jumber wire - Male to female, Soil moisture sensor, 5V relay module,Bread board,16*2 12C LCD Display, Arduino board with cable

[@passiontechklm]

I have made more details video here kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@TechnoPro99]

bro can we do it with other board like with arduino uno r3 if yes so pls give me the code reply now it is emergency

[@passiontechklm]

@@TechnoPro99 Yes this is Arduino Uno R3 board

[@passiontechklm]

You may follow to do this video is more details kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=xlLIOppE0uuKtPUI

[@vaishnavipatil5]

Which wire is used to put the code in the system

[@passiontechklm]

kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@industrialelectricalbd6900]

NICE! THANKS A LOT .

[@passiontechklm]

@@industrialelectricalbd6900 🤗

[@cashmoney3849]

контакты датчика окисляются и перестаёт работать.

[@rizqiirkhammaulana524]

how to connect water pump to relay please show me 😣🙏

[@passiontechklm]

To connect water pump , basically their is two wire for water pump ⛽ one wire is (+) and another one is (-).So just cut off (+) wire and one side connect to Com of relay and than another side of (+) wire connect to No of relay.Thats all bro...try it .but make sure you power off before you cut the wire to avoid any electric short .

[@samosachattraju7030]

What to do with the negative wire of dc water pump

[@passiontechklm]

@@samosachattraju7030Water pump negative wire direct connect to power supply or Battery which one you use.

[@samosachattraju7030]

@@passiontechklm there is 2 positive wires??? One to relay com and one to no of relay how is that possible

[@passiontechklm]

Yes exactly negative wire direct connect to power supply negative.

[@SlickSage]

Can you please state the name of components?

[@passiontechklm]

kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@luqmanafiqabrezaf2338]

Haii bro can u share the library…this project is awesome

[@passiontechklm]

You can watch this bro ..kzbin.info/www/bejne/bXzHmX-VnKakfrM

[@krishnareddy4520]

How much time to take code uploading bro

[@passiontechklm]

Code uploading should be take only a few seconds,if take so long times means something error.

[@krishnareddy4520]

@@passiontechklm i mentioned the same code only but it giving error

[@krishnareddy4520]

@@passiontechklm the display also working as per diagram we did connections but that code showing error

[@mr.marioallinonechannel2766]

Where is the battery 🔋

[@yadhuachu5456]

What is that big board🤔

[@passiontechklm]

You mean I use as wire connected point?Solderless Bread board,

[@pauloamposta4429]

what library did u use

[@wanahmadazim9111]

DO YOU HAVE THIS PROJECT SIMULATION IN PROTEUS?

[@passiontechklm]

i dont have in simulator bro...

[@casperes8765]

good job

[@Awaratraveller99]

when i am uploading the code it is showing #include LiquidCrystal no such file or directory

[@salmansarwar9595]

Same, why?

[@muhammadsyauqiridwan8551]

Hey there! Excellent work here. By the way, can you show me how to connect 12V dc water pump to the relay??

[@passiontechklm]

Hi...if you use water pump practically you just cut off the positive wire of the pump and one side connect to COM of Relay and the other side connect to NO of Relay that it done.

[@passiontechklm]

Relay is perform as switch only.I suggest you use DC water pump.

[@muhammadsyauqiridwan8551]

@@passiontechklm may i email you my circuit and listen to your comments as well?

[@muhammadsyauqiridwan8551]

Also does it have any changes to the coding you have given if 12V dc water pump is added??

[@passiontechklm]

@@muhammadsyauqiridwan8551 You dont have to change anything on code.

[@SebVettel33]

How can i do it without ı2c

[@passiontechklm]

Need to edit the code for without i2c lcd

[@celvinvillela4827]

hello, i made this project also. i used ur vid as a tutorial, the problem is, the pump is not automatically working. The pump is still working even the lcd says the pump is off. i hope u can help me

[@asg-army8804]

No

[@TAMILAN-vo3dv]

Bro display text not coming pls help

[@gourimr876]

what to do when it keep showing 'Liquidcrystal_12C.h: No such file or directory ' when i upload the code?

[@passiontechklm]

You need to add the zip file and library file I have shown in this video herekzbin.info/www/bejne/bXzHmX-VnKakfrM

[@IRAKOMEYEJOHNSONN]

All the codes aren't seen well

[@passiontechklm]

i make more details video here if you wish watch. kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=qxJUDWtvF6J4tVxK

[@Divyanshu_R.S]

Can we use Arduino NANO in place of Arduino UNO ??

[@passiontechklm]

Yes you can use Nano as well.

[@jebejebejebe]

thankyou

[@passiontechklm]

You are welcome 🤗

[@diyasubramanian3567]

Will u Pls share other project details??

[@passiontechklm]

kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@pavankalyanGugulothu]

Helo can I do this project in my college is it working perfectly please tell me

[@sahilrai8592]

Can you share a report of this if you have any ?

[@quirkydna9172]

After connecting with motor , it's not working properly why

[@MOGAMUZAMILABDULWAHAB]

How do I get the code

[@passiontechklm]

the code is in the description link

[@22_payalnikam13]

What is called that two nodes of this moisture sensor ??

[@passiontechklm]

That is sensor probe to detect the soil

[@passiontechklm]

kzbin.info/www/bejne/bXzHmX-VnKakfrM

[@marciobianchini143]

Hello, I made this project as presented, I used the programming as available for download. The system works perfectly, but he does the irrigation and the next day the system crashes and he has to unplug it so he can restart the reading and then make the decision whether to irrigate or not. Does anyone suggest any changes to the code so that the system doesn't crash in the next few days?

[@passiontechklm]

I have made more details video here kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@antidiusrevelian8157]

can i have a source code

[@kingofsuits]

There is nothing seem on my lcd

[@passiontechklm]

Check LCD display wire connetion and press Arduino reset button should be ok.

[@passiontechklm]

I make another video here for more details...kzbin.info/www/bejne/bXzHmX-VnKakfrM

[@kingofsuits]

@@passiontechklm Thanks it worked

[@vamphaizambrevity8940]

Thanks

[@KevinReyes-ft5bb]

can you share the library?

[@passiontechklm]

I have made more details video here kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@phoenixsid]

Why is my LCD Display not glowing ?

[@parveenpanditraison9064]

Bahi lcd par kuch nahi a raha

[@Kim.b_erly]

Thank you so much for this tutorial 👍🏽

[@passiontechklm]

kzbin.info/www/bejne/bXzHmX-VnKakfrM

[@JesúsangelHuaranccaArone]

donde encuentro la programacion

[@krgm7309]

hi there is it possible for you to share the link for the code library you used?

[@passiontechklm]

kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@amirulislam5091]

Bhai diagram Nehi hey???

[@POOJAPATIL-wj5qg]

Can you send me a circuit

[@ayushgurjar]

i got an error in coding what i doo

[@anishbhusal6624]

Automatic waste segregation system

[@areejoon8959]

Hello Is there is a flow chart for it?

[@byebyeyoutube4802]

Your coding is not working

[@Mainak908]

kzbin.info/www/bejne/h3rHdoWYramJq68

[@djamalsaou7468]

code please?

[@tejasbamane900]

How can I buy this project ?

[@gangadharbapatla960]

Your code is not working bro

[@passiontechklm]

I have made more details video herekzbin.info/www/bejne/bXzHmX-VnKakfrMsi=fuMmE9abjHPR-uI1

[@sadliismail9230]

Please shema de câblage

[@naveenmurali906]

Bro components list

[@passiontechklm]

I have made more details video here kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@Divyanshu_R.S]

Sir Arduino NANO ma to D1 pin nahi likha hai kya karu ???

[@sahilrai8592]

What will be the problem statement for this ?

[@joeycarlo6178]

I wanna see an actual pump 😂. I need this to work for me !*. Lol

[@arun--07]

Which arduino Uno is this?

[@hoonpark-tm2yk]

it does not show anything in the lcd

[@passiontechklm]

did you scan your i2c lcd address?

[@Aether-dt8je]

@@passiontechklm how do we do that?

[@passiontechklm]

@@Aether-dt8je check out this video for more details... kzbin.info/www/bejne/bXzHmX-VnKakfrM

[@MuhammadSaadAnwardado]

I don't have motor

[@passiontechklm]

kzbin.info/www/bejne/bXzHmX-VnKakfrM

[@mohammedammar7851]

Your code is not working

[@codered5201]

Circuit diagram bro

[@DivyaRelangi-j4s]

Your coding is not working y

[@byebyeyoutube4802]

Yes

[@Mainak908]

kzbin.info/www/bejne/h3rHdoWYramJq68

[@passiontechklm]

its should work bro , did you modify the code?

[@Yasmeen_ayub]

Bro ur codeing is not working 😫

[@passiontechklm]

what is not working bro....can you done upload ing

[@passiontechklm]

Relay IN connect to D2 of Arduino Uno

[@ladyprivate.7597]

Show how to connect to a water pump

[@josuejoshua3422]

please the schemas of this projet in proteus

[@jefferryan]

salam how I can download model of that project please kindly

[@bhuvanaammu2123]

Hiiii

[@amerdalaten4957]

Ilike it

[@byebyeyoutube4802]

Pls reply

[@bilsemntk4827]

sj

[@benjonaslarenandersen5049]

💀💀

[@passiontechklm]

I have made more details video here kzbin.info/www/bejne/bXzHmX-VnKakfrMsi=7ulVPlTilNpXJ2f5

[@byebyeyoutube4802]

Your coding is not working