Solar LED PowerBank Assembly

[@gregorysinquefield5367]

Bought two of this type charger by order online didn't know that it would arrive not assembled this video helped out great thanks bro.

[@immrnoidall]

lol, me too.

[@lomgshorts3]

If your solder joints are not smooth, shiny, and spreads all over the pad, then you have a cold solder joint that will fail. Never use Tin only solder, always use 60% tin, 40% lead rosin core solder with a thin diameter so it melts at a very short rate so you do not damage the battery. Long contact heat will damage the battery, guaranteed! It may even cause it to combust. Good Luck!

[@valdirdrone518]

Amigo boa noite, muito bom seu vídeo, será que consigo usar uma placa charger wireless no lugar dos leds ?

[@rahulmukundan1245]

This thing is really handy at all time

[@nevermind-wp3bf]

Question. Does it have overcharge protection, or should I buy separately one? I've built this powerbank but I'm afraid to leave it unattended when it's charging. I am allways checking the levels of those 4 leds. 😔

[@captainpotato6584]

probably not bro

[@nevermind-wp3bf]

@@captainpotato6584 I think it does. I am using my powerbank for more than an year and once the fourth led is not blinking anymore, the powerbank it's charged... I lived my powerbank for more than an hour charged (led not blinking) and nothing happened. It was not even warmed. I think it's overcharge protection. It's a very good powerbank. You can use it as a powerbank, a lamp or a lantern either. It's very usefull if you've got the batteries and you know how to asemble it.

[@hawkmontana5521]

Very smooth

[@mozammelhuq9632]

very good video for assemly

[@rpbajb]

I don't understand why you intentionally short your cells at 2:58 . That's quite dangerous.

[@BlackCat-qm3sj]

Hey dont I have to check the batteries before using and how do I do that I dont have multimeter tool

[@stamatogeo1]

what kind of cables are you using?

[@k5hrv605]

You conveniently skipped the part where you somehow soldered wire to smooth surfaces on the batteries, which is a fool's errand. Solution: hot glue and/or lots of electrical tape.

[@oilpond]

🤣🤣🤣

[@roadsurferd]

What happens after 6.18???

[@rpbajb]

Please clean your soldering iron. It's filthy!

[@pravinwaghmare2839]

Mujhe kit kharidna hai amazon pe ye kit available nahi hai please contact me 9423336516

[@uguregitim]

you didn't exactly show the link locations

[@shivnandansharma953]

Ye kaha se milega

[@rafikulahmed8441]

Mera power bank soler charging me srif one light glow hota hai or chargeing upgrade show Nehi hota hai kiu

[@randomfeat1743]

amazing 👌👌

[@ItaloLima]

Good ,Like Bro !

[@stelajoseph6309]

nice frm Tz

[@naraindaskalra4716]

Make a video on how to make arduino software How to program it

[@hamidelkaki7022]

WHERE IS THE LINK ?????????????????????????

[@007asifmohd]

Where is link for the kit

[@thakorbhagvankumaradagama3926]

Ae power bank ki kit Kaha kahride iska modal number do plesh

[@Elite.SpartanX]

Pls give the link

[@vijayakumarkona443]

Bro my humble request is that to make a video on programming of kk 2.1.5 board with fs CT 6b transmitter and explain it very clearly bro Wich will be very helpful full to us bro plz plz plz. So plz make a video

[@sentry1234]

vijaya kumar kona stop spamming bro and plz

[@nileshfamusvlog205]

Bettery voltage

[@sagarpipaliya1319]

Please link bejo

[@sagarpipaliya1319]

Ye khase milta he