Solid Edge 2023 Tutorial - Exercise - 15 (Part B)

[@ronancarroll8554]

I like your videos. Not too fast and plenty of explanation. Could you show how to use the face relate commands. I made an error on this part. On of the counterbores was off centre. I tried to fix it using face relate but ended up having undo, undo, ... to correct the error.

[@drmseif]

Thank you for the comment. If you email me the part and the draft files, I should be able to help. ( [e-mail] ).

[@ronancarroll8554]

@@drmseif I am using the Community version of SE 2023. The professional version doesn't open the community version files. I can send a STEP file though.

[@drmseif]

@@ronancarroll8554 k

[@drmseif]

@ronancarroll8554 I also have the 2023 education version.

[@kalinkakylab7276]

Keep on going, ! And for you folks out there, if you like his tutorials, Can´t be that hard to click on thumb up and subscribe ? That will give him support in amount of views...

[@drmseif]

Thank you so much for the comment and support. Very appreciated. 👍

[@BStott]

It has been a truly long time since I drafted. However, I do believe it is against proper practice to dimension 'hidden' lines. Do not duplicate dimensions. They are unnecessary and cause confusion. Because, a skilled draft reader knows only the required information is on the sheets. Also, you omitted or left out the 120° relationship between the centerlines of the exterior bolt holes. I do not think it is fully evident the relationship is 12mm 3X holes on the flanges are 120° on centerlines. ???

[@BStott]

Note: If you use ANSI Metric for your DRAFT they are still in INCHES for the PAPER. Use the ANSI Metric so you create accurate Draft Drawings. You then can correctly and properly have the Title Block Message: "UNLESS OTHERWISE SPECIFIED DIMENSINS ARE IN MILLIMETERS..." Currently, for years, you have been doing this wrong.

[@BStott]

ALL of YOUR Drafts are specified in the WRONG Units! You always select ANSI INCH for ANSI MM Drawings. You have no good reason to use ANSI INCH instead of ANSI Metric. It makes zero sense and is unprofessional to use differing units templates. Use the ANSI Metric. Next... Note: IF YOU INSIST - to use ANSI INCH for Metric Units - Learn to use the Edit Dimension Definition commands and work with the Prefix and Suffix capabilities to properly indicate the dimensions on the dwgs as 'mm' for the correct measurements. READ the Title Block in EVERY Video outlining a Draft Sheet. --- Each clearly states, "UNLESS OTHERWISE SPECIFIED DIMESIONS ARE IN INCHES..." Also, could you learn to properly edit the Title Block? You've been doing it wrong for over three years, now. So, ALL of your Title Blocks are WRONG. FOR all the Years you have been doing this up to 2023. It would be very advantageous to any students IF you were to learn the application and proper Drafting practices. Drawing Sheet 'Title'. Suggestion: Update and Upgrade to, Solid Edge 2023. Adding text and dropping over code and symbols is WRONG! When using 'Save' and 'Save As' ---> There are fields to update the TITLE, DWG NO, & REV. You are very unprofessional and not knowing to put text ontop of symbols and other text. Wow... The Draft Page Title can be changed during the Save File stage. OR, go into the 'View' Tab > Sheet Views > 'Background' Then, to the bottom of the page see and select the B-Sheet, which YOU use. Then, edit the Title Block. You can figure this portion out on your own. Please - YOU have spent several years making very poorly organized videos to teach poor technique, practices, and wrong actions. And not learned much of anything. You claim to be a PHD??? Students deserve an organized and well presented tutorial, lecture, examples, and tranings from a Phd. You've made many videos over the years of published - very poor quality training. If you do not present professional - you waste time and frustrate students who become poorly skilled workers, poor technicians, lousy designers, bad engineers, low level scientists, etc. Get organized before you make a video, write a script, practice by doing the examples, and post edit your videos.. Get the hums and haws out, the lousy wrong practice mumblings and fumblings, too. Note: I was an active engineer and professional. I am tired of amateur and poor exampled Phds (fuds) patting themselves on the back and getting accolades from the needy ignorant. Be a Man (I noted you are a male.). Be a Professional (You carry a fud (Phd)). Learn and present as an experienced individual. You seem to, maybe, have a few years of extended post graduate training. ??? [I am frustrated with incompetent people in elevated status and positions. So, I'm no longer going to be quiet. You need to upgrade your skills. Raise your quality. You are and example and represent your education, your alma mater, your organization, your family, your heritage, your nation, and --- maybe --- you.] Take care. I do know you have the capability to be - A professional. P.S. I would have sent the above raw shakedown of your poor product privately. But, you made a concerted effort and point to remove all ways of privately contacting you. So, now you bare the rash of a public scolding. I couldn't get to you in a soft, gentle, pampering, quiet, private, professional toned contact.

[@drmseif]

Thank you for the comment. Your feedback is well taken.