Solid Edge 2023 Tutorial - Exercise #18 - Threaded Flange

[@mortenlund1418]

Thank you again. Great and easy to follow. For anyone who do this in ordered mode. After making the cosmetic thread, go to 3D Print and select Physical Thread following the prompts.

[@mustafaiqbal89]

You've got yourself a new subscriber. Well done!

[@drmseif]

Thank you so much for the feedback. I am glad that you found it useful 👍

[@sakthiyaaiyathurai183]

Excellent explanation ❤

[@ps-gq5km]

Can you show how to do clearances for inside and outside thread?

[@drmseif]

Thank you for watching the video, and I will answer your question in the coming video.

[@ps-gq5km]

@@drmseif Nice! Thank you very much! There’s not a lot of good content for solid edge out there, I appreciate your videos.

[@drmseif]

@@ps-gq5km Thank you for your feedback; I am glad you found it helpful.

[@akashbhorade]

Playlists to learn solid edge 1.Solid edge sketching for beginners kzbin.info/aero/PL1iDIuUh--GYBz5i-saQSMhYr6Nd66tap 2.Solid edge basic commands kzbin.info/aero/PL1iDIuUh--GZkfM-UGn27jzPsXPfkABFM 3.Solid edge parts modeling Tutorials kzbin.info/aero/PL1iDIuUh--GYcx4-SeDVh8bQevlWJeAFy 4.Solid edge sheet metal tutorials kzbin.info/aero/PL1iDIuUh--GY06edR96LprjRM3OgOLE57 5.Solid edge assembly tutorials kzbin.info/aero/PL1iDIuUh--GaPDcYzdws7rfk-WBo9IFV6 6.Solid edge drafting tutorials kzbin.info/aero/PL1iDIuUh--GYANu-QR1Bvy9zJ_ldONlX6 7.Solid edge tutorials in Marathi kzbin.info/aero/PL1iDIuUh--GampOF07NZofQsqzlXnHKsG

[@johannesgreiner2690]

Hello- The dimension of 43 mm, mentioned in the top view above the label "SECTION A-A", must it not be 45 mm instead ?

[@tumthanachat7471]

Please make a video teaching how to reverse engineer with Solid Edge 2022

[@Not-Only-Reaper-Tutorials]

i've made it successful. Look can you eventually make a tutorial on Solid Edge 2023 explaining how to set up the dimension symbols and fonts correctly please? I'm struggling to get diameter dimensions that are not visually invasive. SE2023 normally draws the diameter throughout the whole circle (even if you put the measure's figure outside it) filling it in with 2 arrows, diametral line and so on. It's visually cluttering, especially when you have 3-4 or more concentric circles.. I tried to get rid of it making diameter dimension more clean. It seems impossible or, however, it's not so at glance. An our tutorial will help a lot.

[@drmseif]

Thank you so much for the feedback. My next video will be about how to do a GD&T draft for this part in complete detail. If it does not answer your question, please send me an email to [e-mail]

[@Not-Only-Reaper-Tutorials]

@@drmseif well it's not about the draft. This is ok. I'm talking bout the part, when we dra circles to make the part and we fixate the measure by using the smart dimension tool

[@Not-Only-Reaper-Tutorials]

@@drmseif dear Mohamed, I discovered (thanks to one of your video) that this is very ok in ANSI Metric ... wile I always used ISO metric. So I see that the indication of the diameter is different between ANSI and ISO

[@johnmainville6512]

I thought this was the easiest so far!

[@tumthanachat7471]

กรุณาทำวีดีโอสอนการทำวิศวกรรมย้อนรอย

[@danielkulla9384]

✅ *promo sm*