Solid State Relay Like a Interface & PLC

Trying to explain about " SSR " like an interface between two Different Level Voltages, SSR also have not any moving part to control heater,
here we control heater through PLC ( Programmable logic Circuit ) But using SSR Between Heater and PLC,
क्योंकि PLC या Microcontroller कम वोल्टेज व कम करन्ट ( micro or milli Ampere ) पर कार्य करते है ये अधिक voltage / current handle नही कर सकते, अतः एक अतिरिक्त output युक्ति (जिसे SSR कहेगे ) लगाते है, SSR अधिक Voltage / current handle करने के लिए बनाई गई है, (यदि SSR को Output device तो PLC को Driver device कहेगे )

[@AmitSharma-fx2jw]

Very informative video.. Solid state relay aache se samaz me aa gaya hai..

[@harveer420]

Good Evening Sir, I watched every single video that you upload . I live in Australia and I done my engineering from an Australian engineering college but still whenever I watched your videos I learnt a lot . You are a knowledgeable personality . Thanks for exploring your wisdom with us.

[@pushpendrajaipur]

हरवीर सिंह जी, आप ने मेरे विडियो की प्रशंसा की, अर्थात मेरा विडियो बनाना सार्थक रहा, वास्तव मे इससे भी अच्छा गुण आपके स्वंय मे समाहित है कि , " आप मे दूसरे की बात सुनने की क्षमता है " , इस गुण के कारण ही आपने मेरे विडियो की प्रशंसा की है, आपके इस गुण को नमन, उत्साहवर्धन के लिए आभार,

[@manojmian4375]

Very informative video sir...could you send pet-2214 plc manual

[@biswanathamahanta715]

Sir pet stretch machine me is plc use hota hai kindly wiring ka ek video banaiye......

[@pushpendrajaipur]

प्रयास करूंगा

[@SasiKumar-nr1zn]

Good video, Thanks for infermation . I have one doubt how much Dc volt come form PLC to ssr.

[@pushpendrajaipur]

Sasi Kumar In this PLC there are 24 Volts (not DC only signals) to SSR ( in pulses to controls power of heater )

[@dullybrown3635]

Sir! Do voltage fluctuation affect heating parameter?

[@pushpendrajaipur]

You mean about mains ac voltage, so of course the heat generated will decrease or increase in the same proportion as the rate at which the potential is changed

[@lungtentshering5524]

can i you please let me know about the temperature setting to form a accurate bottles of 18g pet bottle

[@pushpendrajaipur]

you may ask setting of temperature to operator.

[@quitesinger1748]

Sir pet-2214 ka manual de skate h mujhe plzz

[@jayverma3981]

Sir pet 2214 mein timer 1...lock time aa rha hai kaise hataye pls help

[@radheymohan1028]

Manual se auto kaise hota hai

[@goldenelectronics986]

Sir please help me. Sir please show back side wiring digram,Schmetic diagram please send

[@pratesh255]

Sir my plc start not starting ..just blinking red lights on buttons for some seconds and automatically plc turn off Help

[@pushpendrajaipur]

क्या power ON button को बिना दबाने के उपरांत भी LED off हो रही हैं, अथवा PLC का ON Button दबाने के बाद, PLC बन्द हो रही हैं, सही symptoms बताएँ

[@pratesh255]

@@pushpendrajaipur sir aaj check kiya phirse tab pata chala wiring loose ho gya thi ...ab thik se chal rha he . Thank u for your reply sir

[@pushpendrajaipur]

@@pratesh255 Good,

[@goldenelectronics986]

Sir please show plc back side Waring digram

[@n.kdistributor2519]

Sir please show plc back side Waring

[@PraveenKumar-yj8iv]

n8ce sir ji

[@pushpendrajaipur]

प्रसन्नशा के लिए आभार, आपके उत्साहजनक उत्तर से विडियो बनाना सार्थक हो जाता है,

[@debajitdutta6999]

Sir plc Sami or hand not working

[@pushpendrajaipur]

What is your requirement , kindly tell clearly

[@amankarn5519]

Sir I need help

[@pushpendrajaipur]

Yes, tell, what you wants

[@amankarn5519]

Sir actually I have pet blow moulding controller I have face the issue the output terminals are not working

[@pushpendrajaipur]

@@amankarn5519 Which output not working ie solenoids or heaters , If one / single output defective then replace it’s output MOSFET , if multiple output defective then check cycle timing or adjust time of timers for delay, If heaters output defective then also check zero crossing 3 phase mains

[@amankarn5519]

Sir 1 2 series is perfect working but 3 4 5 6 7 8 is not working heater

[@pushpendrajaipur]

@@amankarn5519 you are using 1 phase or 3 phase for heaters

[@truckloverskashmir40]

Sir number mil saqta hai ka

[@pappulakher2056]

Hi

[@wafatex62]

Aek se jyada heater on krna hoto

[@pushpendrajaipur]

हाँ, परन्तु आपको अधिक क्षमता के अनुरूप solid state relay लगाना चाहिए, साथ ही आप load share करने के लिए एक की जगह पर तीनों phases पर heater लगाना उपयुक्त व अनुकूल होता है

[@MukeshSharma-ze5df]

Jangid sahab apka number msg karo.

[@vikasshinde212]

Hi