Solution of Laser Cutting: NO LASER BEAM EMISSION FOR IPG YLS

[@astitavsharma1999]

Hi clara, while doing laser cutting on 1500W machine. Material GP sheet 0.8mm Thickness. My IPG source is showing error HIGH BACK REFLECTION & power supply off How to resolve this issue.

[@darlenealderson777]

Muito obrigado, me ajudou muito! Ótimo canal e recomendei pra um amigo!

[@ClaraChai]

Gracias

[@parthpanchal1087]

Make video for laser welding

[@Sir-Mousey]

Hello I'm having problems with the protective window sayingvits iverheating butvits not actualy getting hit it happens instantly gets one to shots and gives up an automatic precitec error how do u fix it

[@ClaraChai]

All lenses okay?

[@Sir-Mousey]

Idk we checked as much as we are able under warranty Caled ipg and they said send it to them for a checkup and repairs since we have a warranty on it still at no extra cost other than down downtime which is extremely expensive in its own right

[@PedroVillagran-w1n]

i have the same problem but in a Raycus laser source. our 3kw source was damaged so we conected a laser source 1kw of our welding machine to cut. the machine was working with no problems but suddenly it didnt emmited laser beam. we already check [mod] wires, measured voltages and checked if theres any alarm but everything looks good. do you have an idea of what could be happened with our laser source?

[@ClaraChai]

Please check whether the laser is in good condition

[@astitavsharma1999]

Dear Clara I am facing an issue with my laser cutting machine IPG 1500W While doing cutting, suddenly laser source turns off & system shows IPG power supply failure & then Shutter gets turn off. Laser source restarts itself. Pls suggest what could be the possible error

[@ClaraChai]

It should be the single module, you could connect to the monitor of the laser and check the alarm and times. Possibly, the power module in the laser has something abnormal.

[@jagpanesar3057]

Fantastic Videos 🙏🏼🙏🏼🙏🏼 learnt more through your channel than the training. can you please help? I can enable my shutter and I get a beam. But when I press start laser goes off and so does the emmision light goes off too and it doesn't cut. What can I check any suggestions please??

[@ClaraChai]

You mean there is red indicator but no laser emission, correct?

[@ClaraChai]

You mean there is red indicator but no laser emission, correct?

[@aliraza-pk9yn]

Hi

[@hussnainarshad1159]

I face this problem in laser cutting machine (IPGPower supply Off,IPG Interlock active) can you help me why this alarm come during work on machine

[@ClaraChai]

Is your machine in warranty?

[@hussnainarshad1159]

NO@@ClaraChai

[@hussnainarshad1159]

NO WARRENTY@@ClaraChai

[@adamgol89]

Awsome channel very helpful. It would be good if you could make video on setting parameters for powers above 6kW

[@pedrovillagran2181]

Hi, I have a Raycus RFL-C6000 laser source and i have no laser emission, stutter can't turn off and i have a message that is not comunication between laser source and pc. Can you help me.

[@ClaraChai]

Is your machine in warranty.

[@roldandechavez1641]

max photonics laser source.. no laser emmission because of humidity warning.. what do i have to do? is there a problem with the humidity sensor? i tried to change the temperature to lower the humidity but after awhile it will rise again to higher percentage..

[@ClaraChai]

Check your mails

[@sauldelgado1489]

Can you help me set up my laser ? I have issues with IPG laser communication with cyp cut. It does work in laser net and some in cypcut but I get a communication protocol version not match error

[@ClaraChai]

[phone]， [e-mail]

[@alaahmidy7563]

Hi Can you help me i have a problem with the ipg laser source When the device is turned on, a short circuit occurs?

[@ClaraChai]

Is your machine in warranty?

[@alaahmidy7563]

@@ClaraChai no

[@alaahmidy7563]

Do you have Whatsapp?? To send you Video about the problem

[@ClaraChai]

@@alaahmidy7563 13335151833

[@winzawlinn3032]

Thank you

[@ClaraChai]

You're welcome