Spark Plug Wire Crimping

[@victorybravo5627]

Viewers, Slide on the boot before you crimp the terminal on the wire.. Even better is to slide the boot on before trimming the insulation. This was not demonstrated.

[@reinbertgahum2861]

Where can we buy this kind of crimping tool ?

[@MrMrsregor]

im confused, MSD's video shows them leaving the black layer of inner insulation on, but Hagerty's video shows them stripping it off .?.!. which is it ? they both seem like a trustable source, but both do it different

[@TheKing-nu4fk]

So how many ohms of resistance is there?

[@Giuseppedg24]

i have a set of msd wires that i broke where the lead connects to the ignition coil, do you sell those ends seperately?

[@charosenz]

Nice tool but I could not tell which part of the crimp head you used for the inner wire, vs, the part for the outer full wire. That should have been pointed out when making the vid.

[@xtreamv]

How are you supposed to crimp them and cut them with that tool that comes with the package?! This video showed me where to crimp.. We need another one on how the tool you guys send with is supposed to work now too.

[@NutT80]

Kind of a stupid moment, but I had no clue that the boot could bend as needed when I bought them. Accidentally melted part of the boot because of the header lol what would you recommend I use to cover up the small hole on the boot? It’s more of a crack than a hole so it should be able to seal, I just don’t know what’s best to use.

[@marineyacht]

where i could buy the crimmping tool

[@jorgealmazan3418]

Goodnight! We are finishing a 1993 Chevy 5.7, carburetor 4 throats, ported heads, headers, flowmaster, camshaft kit, etc. We are going to buy msd spark plugs, some model we recommend ???? Thank you very much !!!! regards!!!!!

[@JP-ek2bq]

Do you have a plug wire set for 1988 560sel benz

[@Harley365]

I came here to watch how to crimp wires not hear you sell your product

[@TPVPRO]

Well dang I always tossed the instructions in the trash. I never used the dual crimp tab I always just fold them back. lol I'm assuming it doesn't make a difference in performance.

[@Camdyland]

I just now ohmed out my Belden edge (napa wires) that was a little over a foot at 45 ohms

[@chrismacias3332]

Can somebody give me the part # of the crumpets he is using on this video please thanks god bless the world

[@richardjoshuatandoc4367]

What crimping tool is that

[@barfyspitz]

Ya...I later found a video by summit that was pretty good. It did a good job showing how to use this crimper. This tool is awesome......the directions suck though lol.

[@morrowdavid30]

Show how to slip boot over because i have been trying for and hour it's impossible even with lube

[@fune2010]

Granatelli wires have near 0 ohms resistance per foot ( less than 1 ohms !! ) it’s the best wires but expensive $121.97 kit 8 wires MSD wires 50 ohms , maybe half price Granatelli wires ... also Granatelli have best colis 60.000V and low ohms resistance but expensive ... MSD Good performance and reasonable price

[@alexquick5957]

How do you get the boots over the plug wire ends you just crimped?

[@TPVPRO]

Alex Quick lube

[@morrowdavid30]

Just returned mine because i couldn't get the boot on even when i put the boot on the wire first

[@1997LT1Camaro]

@@morrowdavid30 WD 40 helps lube it to slide

[@barfyspitz]

2:00 are you serious....nice camera work. 2:17 zoom out and shake the camera so we can't see what is happening......good work.

[@1997LT1Camaro]

I agree this instructional is BS when it comes to camera angles and demonstrating the crimp

[@mikebenoit13]

This dude is representing MSD and doesn't know what the f*** he's doing yeah sounds about right for 2022

[@Bigislandguy]

Come on MSD step it up, now FAST got wires with 25ohms resistance per foot.

[@Syrus54]

Your crappy wire caught on fire. How do I SPLICE the 2 halfs back together???

[@georgesrisomsak362]

Syrus54 your crappy install was likely the fault. Been running this wire set for 8 years, I just now need to replace them due to excessive heat from flat out torturous towing abuse. Will be trying the Taylor Pro race 409's this time around, not because of the product, but just to try something new. Try installing them properly next time.

[@johnwilburn]

1) Remove both burnt ends from the header tube you had them resting on.....

[@edwardteach1855]

John Wilburn 😂

[@s30blazer]

What part of the crimper did you use? Make more detailed video. Slow down, I'm trying to learn how to crimp wires, not interested in the science.

[@Diadem37sGarrage]

I’m pretty sure Taylor Cable is 40 Ohms per foot... pretty sure thats less than 50 lol IJS

[@rendor21]

Stuttering Stanley over here

[@gigitylol6969]

naw man u just chrimp the back side of the silver thing on the wire. easy as that

[@joemarble2176]

Everything makes sense but sliding the boot in trash how u not going to show the most hard part of the process I just stop buying msd I switched to vms wiring best thing ever no wire struggle they thick and perform awesome after 15 years struggle with msd no more

[@justinsnow6335]

More of an infomercial.

[@chico102390]

You need a vice for the tool that comes with the msd Spark Plug Wires. This video didn’t help me much.

[@Se7enthsonSS]

I got 60 on mine…

[@Samson-EC]

I wish you would have devoted the time to crimping. Very disappointed