This has been the most in-depth, informative video series on the features and capabilities of the SPEKTRUM DX5C that I've found. Your explanations of what all of the different settings are for have been invaluable. I really appreciate your having taken the time and energy to teach us "noobs" something new. Thanks!
@QZillasWorld4 ай бұрын
Bruh 5 years later and you solved my issues! With both videos
@tonyquinnell6214 Жыл бұрын
Dude, you do an awesome job of explaining the functions of the RC world keep up the good work I have watched several videos on how to use on KZbin and you are the best you got my subscription
@mildtowildrc73433 жыл бұрын
You broke down the manual easier than I can and taught me a few things I didn’t know about it myself❤️Great Videos👍
@upgradedrc36973 жыл бұрын
Thank you Sir, I appreciate that!
@royarsey54294 жыл бұрын
Thank you ! i learned how to set my DX5C...failsafe / frame rates (11ms) i use it for 3-nitro cars using the new press down bind button receivers & the rest are basic .I use the buttons A-B-C-D for assigning functions / say- A=steering /B=throttle /C=brake ( Nitro car)..i did the timer as well. This is very helpful..Thanks !
@nj20334 жыл бұрын
This is probably the best review of any product I've ever seen on the internet!!! Brilliant extra information on the Traxxas receivers etc... Outstanding!!! Subscribed!
@upgradedrc36974 жыл бұрын
Thank you. I try
@mildtowildrc73433 жыл бұрын
Best videos on the DX5c and I recommend anyone with this transmitter to watch and part 2❤️👍This is a great unit and use for all my RC’s💪🏁
@erterrill4 жыл бұрын
Brother, thank you SOOO MUCH for this video!!! I just got back into RC after 30 yrs and man, stuff is waaaaay different then when I was a kid/teen. I just picked up the Arrma Typhon 3S and this exact remote with the 6100AT receiver. Ran it one time after installing receiver and upgraded steering servo, changed battery after 1st run and receiver stopped working. And you're right, I set up the receiver in a different position after initial launch lol. But thanks, this video was exactly what I was looking for!!
@gonzodetroitify3 жыл бұрын
Trevis let me tell u this has helped ALOT now my rig is my own and not how the factory intended
@cbh1484 жыл бұрын
11:53 my god, what an awesome location to drive RC's! We don't have anything like that here in AL, just loads of trees and undriveable thick brush.
@stevennelson67064 жыл бұрын
This was a great video, I have a Typhon 6s with the 6100at receiver and found that if I mess with the AVC setting in the remote/transmitter it conflicts with the receiver factory set AVC so I had to turn off any input to stop the transmitter and receiver from fighting each other. When in conflict with each other the receiver tries to straighten out the steering when the steering wheel on the transmitter is almost back to center which creates a crazy zig zag RC.
@LayneSteighlee4 жыл бұрын
I have a limitless with the 6100at...are you saying you basically put all numbers to 0 in the AVC portion on the remote? or did you just set AVC to Inh on the remote?
@josephcaruana9165 Жыл бұрын
I purchased five spektrum SR6100AT to fit them in my cars and use them with the DX5C but they are not good because I couldn't use the AVC and had to make the settings to the lowest possible from 3 to 5%. I realised this when one of them wasn't binding and I replaced it with the SRS6110AT and I could adjust the radio settings around 75% and could also use the throttle AVC with the DX5C and the cars moved in a perfect straight line without wobbling. I tried to make contacts to see if they can replace them or give me a good offer but up to now nothing! We spent thousands of euros on this hobby and we should be treated better in my opinion!
@brettkavonic33713 жыл бұрын
Thank you so much for your video. Helped me way more than everyone else. I was forced to set up the dual servos on my e revo 2.0 with the first steering servo in steering port and the second steering servo in AUX 3 of the AVC 6100 receiver. I set the transmitter with the dual servo mix. And have AVC transmitter setting to ON. Throttle and dual steering servos all work when using steering wheel and throttle trigger. But for some strange reason , only the one servo responds to the avc gain. The other steering servo has no avc active. Both steering servos work perfectly when I turn the steering wheel, but avc only works on the one steering servo and not the other. ( I tried using a Y lead to make the servos use only one channel, but was almost impossible to get the leads to fit under the receiver cover ). Any suggestions how to get avc working on both servos ? Should I try plugging second servo into aux 2 maybe ? ( I did read that aux 2 is for gain, so chose aux 3 instead ). Once again, your video was excellent. Any help would be greatly appreciated.
@upgradedrc36973 жыл бұрын
I'm using a Y lead and it works great. I wouldn't use another channel.
@WhiteKnightPoet4 жыл бұрын
Concerning what you said at 33:39-43 on your video (about the necessity to re-bind after changing the steering travel and/or the throttle travel), before I watched this video, my Hobby Shop had already performed the BIND for my Spectrum DX5C transmitter while the STR TRAVEL and the THR TRAVEL were both set at 100%. I re-set the TRAVEL for both the STR and the THR to 70% (without RE-BINDING, because I didn't know any better at that time) yet the RC CAR continued to work perfectly (with the AVC) at the 70% throttle and the 70% steering without re-binding.
@upgradedrc36974 жыл бұрын
Thats great, keep using it then . The book from spectrum says to rebind after adjustments changing the travel, reverse setting, or want to use the receiver for a different model memory. If it and the Avc are working properly just go with it.🤘
@peterberghmans5 жыл бұрын
I want to thank you very much for the fantastic and calm and very understandable way in which you explain everything. you have helped me fantastic to set up my new arrma infraction truck together with my spektrum dx5c .. really fantastic ...
@Eric783603 жыл бұрын
Appreciate this video my man!! Helped me out like no other. Well explained and nice on the detail..
@carlorc63852 жыл бұрын
Hi brilliant video I have the dx5 rugged, and just purchased the Arrma Fireteam, I want to assign aux 1 to button G for handbrake which is not a problem, but can I assign another button D for the timer Thanks Carlo
@upgradedrc36972 жыл бұрын
Yes, if you go to the menu and select "Timer", you can select D or any other channel that is not being used by something else.
@carlorc63852 жыл бұрын
@@upgradedrc3697 Brilliant thank you very much for your help, your original part 1 and part 2 are on my favourites, the best video so far explaining about the DX5👍👍
@chrisslky70184 жыл бұрын
Thank you. Been having “drunk steering” problems with a scale truck. Also had assigned aux 1 and 2 to E and F. Cutting the plastidip off and starting over. Disabling the AVC all together.
@FrankLSD383 жыл бұрын
For AVC to be disabled the second bind plug ( aux4) must stay in after binding... for the same reason you mentioned ...in competition it easier to prove its deactivated just by glancing at the receiver and seeing the plug
@cameronjurow2724 Жыл бұрын
🍳🌊🍋🌈🍊💨⚡️
@cameronjurow2724 Жыл бұрын
Dr😊c L😊 B Hern
@dvi-d68 ай бұрын
Hi there. Hopefully this message gets seen. So a strange thing happend. I turned on my kraton for first time in maybe 6 months. So Dx5c on, car on… now usually you have the common 5/6 beeps the car does before its ready to go. But now it does like 2 beeps then the fan slows down and its just idle. But check this… if i turn my steering full right lock it ramps up the fan again, the beeping resumes as normal and then its ready to go. It will actually drive (but only in full lock to the right😰) when i let go of the steering wheel the the fans slow down again and the car is idle. Any idea how to fix this bizarre problem?
@severalothers5 жыл бұрын
Great instructional video, this is the transmitter I am buying and this helped a ton. Thanks for sharing.
@marksmola72994 жыл бұрын
Your a very good teacher. You helped me immensely. Thanks, I’m new to the sport would you tell me what brand and model of vehicle you used on the table during your video?
@upgradedrc36974 жыл бұрын
Brand and model of radio? Spectrum dx5c. Or the car, E Revo 2.o by traxxas
@tonylamas86822 жыл бұрын
Dec 4 2022 you are a exelente explanation 🙌
@echeverrialanz2 жыл бұрын
Dear Upgradedrc. I bought both, the DX5 Pro and the DX5C both transmitters says they are compatible with DSM2 in the 16.5 ms. Frame rate, but non of them would let me select that frame rate because it doesn’t show on the screen. They jump from 11 ms. to 22ms. With out showing the 16.5 ms. Option. Could you help please? I all ready dig all internet and no information found.
@upgradedrc36972 жыл бұрын
What knid of reciver are you using?
@choke6664 жыл бұрын
THANKYOU. FLYSKY NOBLE HAS SINCE WON MY ❤. ESPECIALLY FOR THE $.
@gravediggerrc3 жыл бұрын
HELLO UPGRADED RC WHERE DID YOU BUY THE GRAPHIC IN FRONT OF THE SPECTRUM BOX ???????
@upgradedrc36973 жыл бұрын
I think it was Autozone
@soundcheck572 ай бұрын
Hi! How can i factory reset that thing? 🤔 I bought it used and wanna reset it completely.
@azbrown82111 ай бұрын
My friend I need some help. I just bind my spectrum DX5C to my Outcast when I turn right it goes left. When I turn left it goes right need help
@gravediggerrc2 жыл бұрын
hello there if your motor has to much power what button do you use to lower it ?????
@upgradedrc36972 жыл бұрын
Under Travel go to throttle click on it and adjust the high to your desired setting.
@youray573 жыл бұрын
Did you ever do that video on "mixing "? If so is there a link please?
@upgradedrc36973 жыл бұрын
Sorry, have not done it yet. If I had an RC that required mixing, then I'd have some knowledge to offer you. At this time I do not.
@BulldogsRC Жыл бұрын
Can the timer button be reprogrammed to be used for the handbrake?
@upgradedrc3697 Жыл бұрын
No, for some dumb reason you can only use that button for the timer
@alfonzowowgoheredotcom33854 жыл бұрын
You are the only one !!! Thank you for showing where the wires go “on the Receiver” … You’re the only one I found that did it … All the other instructors are brain dead !!! But why the frick didn’t Spektrum put the word “Bind” on the receiver ????? 😡😡
@T-Gill7773 жыл бұрын
Don’t get discouraged Guy it’s seems very complicated at first I got discouraged also after crashing five maidens it wasn’t a good feeling butt once you figure it all out it may take you a while it took me four months but now everything seems pretty easy after watching 15 videos now I’m re-programming all my planes to fly the way I like them too I love it it’s awesome I could program all my buddies planes Also it’s easier to show someone in person exactly what to do you just have to know where to go and what to do hang in there you figure it out “you could do it “ pilot Brian Phillips favorite quote
@gregoryduvall47583 жыл бұрын
I have the Bronco and the blazer I installed the DX5C into the Bronco and to the Bronco and the Bronco is slower than the blazer in both gears could that be something that has to do with the radio?
@upgradedrc36973 жыл бұрын
It's probably different motors, gearing, esc, etc. But, there are rates that can be turned up on the radio. All the rates are at 100% default when you un box the radio. The video explains it well, just watch both parts all the way thru.
@gregoryduvall47583 жыл бұрын
Both stock,other than tx and rx, I will re watch the vids, thank you
@fmimages2 жыл бұрын
I bought a used one since I can’t afford a new one. Well so far I can’t get it to bind. I did fix my DX3c but the steering wheel spring I replaced is a little too stiff so I got the DX5c but it won’t bind.
@upgradedrc36972 жыл бұрын
What kind of receiver is it
@m.g.5477 Жыл бұрын
I updated my rx sr6100AT and when I try an bind I can't calibrate When I see it bound I proceed to set the throttle and brake and the truck takes off. I read the change notes and it says auto calibrate but I see nothing in the notes that says to do anything different in the binding process please help if you can
@upgradedrc3697 Жыл бұрын
Try unplugging your esc from reciver and bind first, then connect to esc and calibrate.
@m.g.5477 Жыл бұрын
@upgradedrc3697 okay thanks I will try this and see if this will allow me to do it correctly 🙂
@jamiem7620005 жыл бұрын
Great video series very helpful. Thanks
@MetalModelMaster3 жыл бұрын
Can this version of the transmitter display telemetry data?
@upgradedrc36973 жыл бұрын
No
@MetalModelMaster3 жыл бұрын
Damn, alright. Appreciate it sir
@T-Gill7773 жыл бұрын
Another question is the smart receiver Compatible with any moter controller with or without the telemetry ?
@upgradedrc36973 жыл бұрын
Almost all ESCs will work with any reciever, but not all reievers will work with other telemetry.
@keithaseelye1203 жыл бұрын
I did the bind just like you explained but i can not get reverse to function just forward and break but i do have the 6100 not the 6000 does that make a difference
@upgradedrc36973 жыл бұрын
No, try adjusting your reverse. make sure the rates are up to 100%
@keithaseelye1203 жыл бұрын
@@upgradedrc3697 i did and still no reverse i even disabled avc i also did a bind to my 3s senton with a 3 channel spectrum receiver and it worked fine it just wont work with the 6100 i am at a loss it even seems i have a loss of power when using the dx5 on my kraton changed back to my dx3 and it runs great still using the 6100
@upgradedrc36973 жыл бұрын
Huh, have you done an upgrade using the data port? It seems weird to me, I have binded with lots of different recievers and had no problems.
@keithaseelye1203 жыл бұрын
No have not ever done an update im still fairly new at this going to start from scratch again in a few days after i enjoy some bash time using my dx3 trans then ill give it a go one more time for now the dx5 is working great with my senton and i think ill set it up with my second kraton. That one has spectrum esc and see if it works on that first
@keithaseelye1203 жыл бұрын
Oh and a big shout out to UPGRADED RC for the very well done tutorial vids and trying to help me out ill keep ya posted on how this turns out ill probably do an update as soon as i figure out what all i need to do
@MetalModelMaster3 жыл бұрын
So I can bind my car and calibrate the esc but when I power it off and then go to run it again I have to re bind because the transmitter or my reciever doesn't respond.
@upgradedrc36973 жыл бұрын
What receiver and transmitter are you using?
@MetalModelMaster3 жыл бұрын
I'm using the DX5C and the SRX200 reciever.
@MetalModelMaster3 жыл бұрын
I just upgraded my reciever and it fixed the issue.
@upgradedrc36973 жыл бұрын
@@MetalModelMaster That's great to hear. Glad it's fixed for you.
@markpurifoy83024 жыл бұрын
Thanks. Was having a hard time binding. This helped.
@theseniorstechclub53502 жыл бұрын
Awesome job,,,really really help out,,, perfect info
@johngantner93143 жыл бұрын
is there a radio that is not so confusing? was condidering futuba
@upgradedrc36973 жыл бұрын
In my experience Futaba is more cpmplicated.
@devonbettolo4 жыл бұрын
I didn’t need a bind plug with my kraton?
@TyPressley_Creations4 жыл бұрын
What it the blue traxxas support bar part number? Looks like a good support
@upgradedrc36974 жыл бұрын
Tra5632 rear aluminum support bracket in blue. $10.00
@99ville4 жыл бұрын
The stock remote for the arrma infraction has 3 options for the speed, how do I adjusts those options after binding to my smart remote?
@upgradedrc36974 жыл бұрын
Sorry I honestly don't know
@LayneSteighlee4 жыл бұрын
@@upgradedrc3697 He is talking about the throttle limits...the DX2E Active control has a switch for 50/75/100.....I too am watching this video to see how to adjust these on the DX5C.
@LayneSteighlee4 жыл бұрын
did you ever figure it out mo Hawk?
@upgradedrc36974 жыл бұрын
@@LayneSteighlee ?
@jonb2613 Жыл бұрын
HELP! Just switched from the basic Specktrum tx for my spekrum DBX Pro. One feature I cannot figure out. Originally when you pushed foward for brake followed another quick push forward the reverse would activate. With the dx5. Pro its messed up.Push forward on tx and it immediately goes into reverse.😢
@upgradedrc3697 Жыл бұрын
There is a setting on your esc for this. Usually you have a choice of fwd/rev or fwd/stop/rev
@michaelrajca60434 жыл бұрын
i am kinda newer to crawlers and surface vehicles. what brand of rx s are able to bind to this radio. i know several brands of rx s will bind with spektrum plane fadios. also lets say i buy another brand rtr vehicle and want to use this radio. do i have to change the rx to a spektrum?
@vanenmar74912 жыл бұрын
When the AVC thing came out I got my pants pulled down with an AVC receiver and Spektrum/Horizons usual small print bs. What they basically mean with their AVC receivers is that you can have the number of channels advertised, or AVC, but not both.
@upgradedrc36972 жыл бұрын
Exactly, don't know why they did that!
@pitbikecookracing33242 жыл бұрын
Thanks a lot . My AVC is on point now 👊👍
@integrityrc73563 жыл бұрын
How do I program a car and it stays programmed on that car and not carry over when I select another car
@upgradedrc36973 жыл бұрын
When you select a different model it has all it's own settings. Your setting will stay the same on each model the way you set it up. So that each model has it's own settings and will not change. Every time you add a new model it will start over with the default settings only for the new model, then adjust your settings for that model and save. When you switch back to the previous model all the settings will the same as you left them.
@integrityrc73563 жыл бұрын
I got it after the 2nd video. I had bind after any changes. 👍🙏
@integrityrc73563 жыл бұрын
Always rebind if you make changes!!!!
@upgradedrc36973 жыл бұрын
@@integrityrc7356 You don't have to bind after all changes . Only if you change the servo reversing after binding, or change the travel after binding or use a different receiver!
@integrityrc73563 жыл бұрын
That is pretty much what I got from your video. Very helpful. Thanks again. Will definitely press on your button again. 🙏
@ronaldmitchell17474 жыл бұрын
how do i address my steering from the start after binding and calibration. its not going straight or should it be.
@upgradedrc36974 жыл бұрын
Adjust your steering trim until its straight.
@nontl51973 жыл бұрын
How do you set failsafe on AVC receiver ?
@ericwilson87894 жыл бұрын
I have the sr6100at receiver and can't calibrate the throttle. When calibrate steering R N L it's good but I can't calibrate the throttle. Pull back to full throttle nothing back to neutral nothing full brake both throttle and neutral say ok but motor won't spin.
@upgradedrc36974 жыл бұрын
It took me acouple of times also. I found that it was all about the pause inbetween throttle and brake. It's a littlebit tricky.
@FLSharkdiver4 жыл бұрын
Massive thanks for the in depth review on how to this Spektrum DXC5 transmitter works!!! Question, I have binded everything but my Notorious 6s Arrma Stunt Truck but it still does not want to drive straight it just want to drives to the right a tad bit not a lot but a little. Do you adjust the Sub trim to make it drive straight - Any recommendations would be greatly appercaited?!
@upgradedrc36974 жыл бұрын
You could add a point or two to the sub trim , but there are other ways to attack it. if you watch #2 video on this, I explain it pretty good around 6 mins in or so. but, make sure all your bearings and caster, camber, toe in and out etc are dialed in before you go to far out from center on trim points. I have a great video on adjusting camber and stuff also. Good luck brother!!
@hunterfields40382 жыл бұрын
Can I reverse my steering on this remote
@upgradedrc36972 жыл бұрын
Yes, go to reverse on the main menu, then just pic steering and click on it.
@chuckjones44124 жыл бұрын
Should AVC be used in a crawler?
@upgradedrc36974 жыл бұрын
You know, thats a great question. Some people will say yes, and others no. I don't vuse it in my crawler. I found that a smaller pinyon gear will give way more control at slower speeds than AVC. So i guess it's up to you.
@jaredsay33313 жыл бұрын
I do not use AVC in any of my crawler but my basher yes and my drift cars and if your racing drag car you shouldn't but if your just missing around yes
@FLSharkdiver3 жыл бұрын
How to I turn down my Brake since its set at 100%?
@upgradedrc36973 жыл бұрын
There is no drag brake on this radio. The brake is controled by the esc being programed on some esc and others have pin that can be changed from 100% to 0% in increments
@FLSharkdiver3 жыл бұрын
@@upgradedrc3697 Thanks but I figured out how to turn down brakes on my Radio from 100% to 60% for my ARRMA Infraction ..
@hunterfields40382 жыл бұрын
My baby touched something now my throttle is reversed. Pull for reverse and push out for throttle how do I fix this
@upgradedrc36972 жыл бұрын
On the main menu select reverse, then scroll down to throttle and switch it back to normal. Super easy.😎👍🤙
@gfyracing76323 жыл бұрын
How would this compare to the rugged version?
@upgradedrc36973 жыл бұрын
Almost the same except for the rugged case and the selector buttons instead of the thumb wheel which lots of people hate Lol!
@MrGirodog4 жыл бұрын
whats range on it? does it have a anolog throttle limiter ?
@upgradedrc36974 жыл бұрын
No. Analog theottle limiter. Distance is around 1/4 mile
@MrGirodog4 жыл бұрын
UPGRADED RC thanks , is it more responsive that SXT 2 and is there a throttle limiter at all ?
@upgradedrc36974 жыл бұрын
Yes, it is more responsive. But does not have throttle limiter
@upgradedrc36974 жыл бұрын
But, you could turn down the rates and limit the throttle that way.
@MrGirodog4 жыл бұрын
UPGRADED RC EPA ? Lot of them have it now . End point adjustment
@Douger318 Жыл бұрын
i just got one sure like it very light and nice made
@keithbates84823 жыл бұрын
How do set up the fail safe on this remote
@upgradedrc36973 жыл бұрын
If you leave it centered it sets it self. Just forward, reverse, center, release. its automatic unless u change it.
@og1905 жыл бұрын
I'm curious what are all the cans of ed and such used for are there lil trick uses they are used for ?
@upgradedrc36975 жыл бұрын
I'm sorry, i don't understand the question you are asking me?
@FLSharkdiver4 жыл бұрын
#UPGRADEDRC - Many thanks brother for the in depth Tutorial on this complexed Transmitters!! I was able to bind my #6s #Notorious / #6s #KRATON with SR6100AT receivers along with AVC Technology w/ no problem!! You made it a very easy to understand all of the options and menu's that can be a bit confusing if you never have owned one! I have a question since I went with the SR315 DSMR 3-Channel Sport Receiver for my 3s Typhon which would be model # 3 on my DX5C receiver. Instead of a bind plug for the SR315 DSMR 3-Channel Sport Receiver you just hold a button which i did and completed the bind mode and name the model TYPHON and everything worked perfectly for my 1st session ok!!! Now before i WENT out for my second speed run I went to punch level to 5 instead of the default setting from the factory which comes at 3. Ok no problem, got it to punch level 5 and went to turn on the DX5C w/ SR315 DSMR 3-Channel Sport Receiver and for some odd reason I can not turn the steering from right to left. My servo seems to work just find but it seems like it does not have enough torque to turn the servo saver arm since it turns but only 20% instead of 100%! The Throttle works and forward and reverse W/ NO PROBLEM but cant get the steering to turn my wheels. You can actually hear my Savox servo trying to turn my HR bellcrank but it just seems like it does not have enough power to turn my wheels from left to right all of the way! i HAVE TRIED TO rebind it with a new model but still cant get those wheel to turn like the every first run! Could it be my servo horn but whats wired is everything worked the first time WHEN i FIRST BINDED the SR315 DSMR 3-Channel Sport Receiver w/ my DXC5 Transmitter! I am clueless and could use some help, it would be greatly appreciated.
@upgradedrc36974 жыл бұрын
Did you turn off the AVC? It will not work with the sr315 and can cause problems usually with the steering.
@brettkavonic33713 жыл бұрын
Your help would be greatly appreciated as per post just below.
@fmimages2 жыл бұрын
I think I found why it won’t bind but I will have to wait till the morning. I didn’t set the frame rate since I’ve never ever had to do it. I’m old school and all my cars are over 10 years old and this technology didn’t exist for the common basher.
@THATHATSALLFOLKS3 жыл бұрын
BOODS FEEL EVEN BETTER IN MY HANDS
@fmimages2 жыл бұрын
A very good video as I was thinking of getting a drag car and they use AVC.
@chadcheney75975 жыл бұрын
New to the group and have been having a bit of an issue trying to incorporate my winch to my radio system without having to get a separate control box. I'm running the spektrum dx5c with the sr415 4ch reciever is it possible to do what I'm trying to do and operate the winch off one of the 2 auxiliary channels open on the reciever?? Any help will be greatly appreciated
@upgradedrc36975 жыл бұрын
Yes, you should be able to use an auxiliary channel for your winch.
@chadcheney75975 жыл бұрын
@@upgradedrc3697 can you please tell me how to do it with the dx5c transmitter? I acquired it with no manual and don't have the paper to print it out off the net
@upgradedrc36975 жыл бұрын
@@chadcheney7597 plug in you winch to an auxiliary channel. Then select that channel on the radio and assign a button or switch to operate the winch. That should be all you need to do.
@d-val45035 жыл бұрын
Does this transmitter read out telemetry?
@CaviDS3 жыл бұрын
one comment, when dissabling the AVC the will blink when on to show that AVC is dissabled
@upgradedrc36973 жыл бұрын
I'm not sure, never disabled mine. I would assume that it just won't do anything.
@CaviDS3 жыл бұрын
@@upgradedrc3697 It does blink, the reason is so race officials can see that it is indeed disabled
@Nuts-N-boltsinurmouth5 жыл бұрын
Is it possible to run the dx5c off nimh batteries instead of aa ?
@upgradedrc36975 жыл бұрын
Honestly, i'm not sure
@Nuts-N-boltsinurmouth5 жыл бұрын
@@upgradedrc3697 I found out I can I just need to solder a connector on to the wires. Going to use a 4.8v 2000mah nimh pack.
@kennethcombs44194 жыл бұрын
Great vid and have a question as to why when I Set my DX5C SPECTRUM in Aux assign i want to assign Aux 2 for my dynamite kill switch but it keeps going back Aux 1 for some reason...WHY is it doing the after i set it to AUX 2...Why
@upgradedrc36974 жыл бұрын
Do you have AVC. Is it on and automatically assigned to aux 2?
@kennethcombs44194 жыл бұрын
@@upgradedrc3697 I have been trying to disable it in transmitter and binding using 2 bind plugs my transmitter is also making a repeated sound when squeezing the trigger on my Dx5c spectrum or using the brakes
@kennethcombs44194 жыл бұрын
Should I just use Aux 3 which is not assigned to anything
@upgradedrc36974 жыл бұрын
@@kennethcombs4419 trying to disable what? and why are you trying to bind with 2 bind plugs?
@upgradedrc36974 жыл бұрын
Yes, just use Aux 3
@johngantner9314 Жыл бұрын
Thankyou! Sir this saved me Thankyou so much!
@yaffajaff5 жыл бұрын
Hey thanks for the informative video. Just bought this transmitter with the SR415 receiver. For no.6 in binding, "move throttle channel to the desired failsafe position" is that just neutral? Or am I supposed to hit full brake?
@yaffajaff5 жыл бұрын
If the failsafe is set to full brakes, won't that risk my car from flying off in reverse if it lost signal? My ESC is set to FWD/BRK/REV
@upgradedrc36975 жыл бұрын
It is a little bit deceiving in the book, but it is preset for you already
@yaffajaff5 жыл бұрын
I see, although the throttle channel was reversed so I had to rebind anyway So I set a bind for a full-brake failsafe to test if my Arrma Notorious would fly off in reverse if I turned my transmitter off. It enabled the brakes when the car was in forward throttle mode at the time I turned the transmitter off, however the car DOES fly off in reverse when you're reversing the car at the time of radio loss 😵😵😵 unlikely as that is Not the radio's fault, I'm guessing all radios have a failsafe that works like this because they can't differentiate between brake and reverse, but this is why I set the failsafe to neutral instead of full brake, I'd rather the car stop by hitting a wall than risk watching it from a distance going on a reversing rampage lol
@guymarotta25963 жыл бұрын
How do you delete a model from the memory?
@upgradedrc36973 жыл бұрын
Go to model select. Select the model to delete, then scroll down to delete and select it. super simple!
@guymarotta25963 жыл бұрын
@@upgradedrc3697 Which button do you use to delete after you select the model?
@upgradedrc36973 жыл бұрын
Scroll down with the thumb wheel to delete and push the thumb wheel to select. Did you watch the video?
@dynasty48514 жыл бұрын
I have a dx5pro. I am using lights for my aux1 and aux2. Your review I think just confirmed that it's not possible for me to turn the lights on and off upon demand. Is this true?
@upgradedrc36974 жыл бұрын
No, you should be able to.
@dynasty48514 жыл бұрын
@@upgradedrc3697 how would I be able too? Should I make a video to show you?
@upgradedrc36974 жыл бұрын
You should be able to plug lights into receiver aux, pick button and assign it to the lights.
@vwoffroad51015 жыл бұрын
I have all wheel steer rock boncer my receiver went out can I just use 3 channel receiver on the dx5c and if so will it work with off brand receiver
@upgradedrc36975 жыл бұрын
Honestly I'm not sure. But i would think so with some adapters maybe.
@FrankLSD383 жыл бұрын
The DATA port makes for a nice Binding Plug storage...always have it with me...
@TooLs4914 жыл бұрын
I'm having a problem with setting up my aux option on my radio. Any suggestions would be much appreciated. Great videos btw
@upgradedrc36974 жыл бұрын
What problem are you having?
@eventidewinds4 жыл бұрын
what a perfect video, thx!
@paddlesworthrcpark82154 жыл бұрын
Top job very well explained thanks nearly lost all my hair 😂
@DEADBROKE-SN_NATION3 жыл бұрын
Can anyone explain to me why it is i have a brand new reciever the 6100 and i bind it and not even an hour after using it? Its stuck in bind mode as soon as i power it on
@upgradedrc36973 жыл бұрын
?
@DEADBROKE-SN_NATION3 жыл бұрын
@@upgradedrc3697 ? Its brand new i bind it once turn my car back on and it wont link up has to be re-bind everytime
@upgradedrc36973 жыл бұрын
@@DEADBROKE-SN_NATION are you taking the bind plug out after binding?
@DEADBROKE-SN_NATION3 жыл бұрын
@@upgradedrc3697 its the newer ones with the button and no the button isn’t stuck
@upgradedrc36973 жыл бұрын
The reciever could be bad. Make sure everthing else is hooked up correctly and you bound and calibrated correctly. It sounds like a short or bad ground in the reciever.
@99ville5 жыл бұрын
since switching to this remote none of my cars go in reverse and have no brake.i cant calibrate any of my esc's, when I go into full reverse the esc wont recognize. how do I fix this?! ive only used stock transmitters so im totally lost
@upgradedrc36975 жыл бұрын
Check your servo travel and rates. Make sure their not all the way to one side having more travel than the other side. Does the esc bind well with the radio?
@99ville5 жыл бұрын
Yes it binds well I just can’t calibrate my esc
@jbird90625 жыл бұрын
Great video and it's a great alternative to stock traxxas. I have 1
@upgradedrc36975 жыл бұрын
Thanks brother 🤟
@TECKMECK934 жыл бұрын
Thanks love it, awsome thanks again ❤️
@LeftenantMalachi5 жыл бұрын
Can this be used to turn off and on LED lights on my Gen 8 if I want to?
@upgradedrc36975 жыл бұрын
Yes
@restore645 жыл бұрын
I was really pumped to use this but I guess it doesn't do what I thought it would. Setting endpoints, what my TQi wouldn't do on my Stampede 2WD because my servo is in reverse, no problem. But everything else... is really weird. I was hoping I could set the throttle travel/rate to something lower so when kids ask to play with my RC car it doesn't haul ass but when I reduce either one I lose the ability to brake.
@upgradedrc36975 жыл бұрын
Use the exponential and servo rates to slow down the aggressiveness of the beast. Works great for my grand kids
@robertpashley53524 жыл бұрын
How much do they cost to buy and wots the range on it
@upgradedrc36974 жыл бұрын
I paid $129,00 @ the local hobby shop. The range is a lot farther than u can see. About a mile i think.
@wildmangeorgesrcchannel69165 жыл бұрын
Glad I got this one over the rugged one
@leroy52023 жыл бұрын
Can not believe the price has gone up so much.
@matthewneufer17585 жыл бұрын
Where'd you get that deal at I bought my d r x r 4 Pro 4 years ago and it was almost three hundred bucks
@upgradedrc36975 жыл бұрын
At my local hobby shop
@rodmoncrieff22905 жыл бұрын
just unboxed it, thanks.
@brettskinner58244 жыл бұрын
I need help i have no reverse on any of my rigs
@upgradedrc36974 жыл бұрын
What percent do you have your travel set at for the servos? Did you offset any of your sub trims, or are they still at 0? Do you have any servos set to the reverse position or are they all normal? What are your rates set at? If you can answer these questions it would help me narrow it down. 🤘
@brettskinner58244 жыл бұрын
@@upgradedrc3697 Servos are at zero for the most part some i have manually adjusted slightly i had to reverse throttle on one of my crawlers i haven't adjusted any settings just none of my rigs will reverse
@upgradedrc36974 жыл бұрын
Try adjusting your throttle rate on tbe servo from the remote under rates. Try going both ways to see if you get reverse at any point. If not make sure all the Reverse functions are in the normal positon (reading normal under the Reverse menu on the remote), then turn off your AVC, and make sure all servo rates are at 100%, then rebind and see what happens 🤞
@salvadorrobledo11513 жыл бұрын
Thanks a bunch!
@derrickmcclamb59052 жыл бұрын
great video
@shanetrogdon95495 жыл бұрын
So im kinda new to rc stuff, i got a car and this remote from a pawn shop, loved it. The battery on the car died and i plugged it into the data port thinking it was a charger for the battery. Controller started to smoke, and now wont turn on. Is there any saving this controller.
@upgradedrc36975 жыл бұрын
I have never heard of this happening before. it sounds like you smoked your data link and maybe the data board. you could probably replace these parts, but it might cost as much as the $109.00 controller it self. my advise would be to get a new controller with the instructions so you know what all the ports are for.
@sameuljones54965 жыл бұрын
You cocked up big time Shaney Boy
@flixproduction68755 жыл бұрын
I like your vid it help me i just got one
@bassmanjazzbass5 жыл бұрын
Savox steering servo wouldn't extend all the way....100%-150% no diff....turned out to be frame rate. Was set at 22. Thank you sir.