Stair Lighting Connection with Motion Sensors / How to Wire Stair Lights Using Motion Sensors

[@ThaDraGun]

This is exactly what I want to do! Great video, but where do I find the sensor and lights??

[@boopeshkumarprabhakaran]

really helpful... you could also add turn on lights manual switch connection and turn on and off motion senor switch.. please make a updated video regarding this and also what about ground circuit?

[@binucharley]

P

[@LensNmouse]

Highly informative.

[@peterjesus816]

Thanks you for updates but in normal lighting wiring we normally take the hot or supply line to the switch and we take lamp feed to the lights, is this the same case in this wiring cause i see two hot lines, please can you help and explain it?

[@ManikTeknik]

Good videos 👍

[@slengineeringacademy2234]

Thank you.❤❤👍

[@ivantash5033]

Thanks for the update

[@slengineeringacademy2234]

❤👍❤

[@danielteyehuago1633]

Thanks for sharing it with us...

[@boopeshkumarprabhakaran]

also plz add the motion senor product link to buy

[@tiktokersvideos1168]

Good videos easy to understand Can you make a video on Three phase automation system, wapda, generatetor, MC breakers, MC, automatic module, 8 pin relay,s timers

[@slengineeringacademy2234]

Thanks for watching and your comment..❤👍 I will try to do videos regarding above topics.

[@ManikTeknik]

👍

[@hailujardines]

Great. Please add links to buy motion sensors and wall lights.

[@neelakarnakar6499]

Hi @ Hailu Jardine, for motion sensors Contact me 9398678595

[@festusgathecha6637]

Good

[@greenearthblueskies8556]

Best

[@Ash_G]

The _load output_ terminal for PIR1 will also power _load output_ of PIR2 because they all are in series. Won't this be a problem? Do you think 1-way diode should be fitted to protect each _Load Output_ terminal or use of OR-gate relay?

[@Mrbrownthesemite]

Lol. Dude.n

[@dhruvmehtaphotography]

This is exactly what I was thinking, did you find any useful information about it?

[@Ash_G]

@@dhruvmehtaphotography I bought all the components and in different models from AliExp, and built a test unit myself. No problems so far. My staircase has been lighting automatically since 2017. The 2 PIR and one LED bulb still going strong. But since I haven't tested the input nodes with a voltmeter, I cannot say if what I have done is correct/safe.

[@dhruvmehtaphotography]

@@Ash_G so this circuit actually does work fine without a one way diode? Probably the sensor have an inbuilt one way diode?

[@Ash_G]

@@dhruvmehtaphotography Basically when drawing your circuit diagram, treat PIR units as parallel on/off switches. Keep circuit simple first. One power source, two PIRs in parallel and one LED lamp. Your PIR sensor will indicate maximum load wattage it can drive. Some PIRs have 2 terminals but most have 3 (Live, neutral and load)

[@e.welectricalsolarservices3664]

Nice

[@slengineeringacademy2234]

Thanks .👍❤

[@RockyBhai-bf5ml]

❤❤

[@ammayapper]

👌👌👌👌👌👌👌👌

[@SSMondal.786]

👌👌👌👍

[@slengineeringacademy2234]

❤👍

[@tonnawong2642]

Nice video ... What if the motion sensor have 4 wires stickin out is the connection still the same ..

[@eksine]

4 wires means it has 2 input and 2 output , you would need to wire it in a way that it would breaks the circuit

[@bboozer93]

Can this set up be switched with a dimmer. Example the switch with the dimmer is turned on and then the motion detectors will turn the lights on to the selected brightness. If the switch is off then no motion activated lights

[@abhisheksinghrathore108]

Excellent video but I have one doubt we use charger Or give direct line.

[@slengineeringacademy2234]

Thanks for watching..❤❤👍 We use direct line.

[@esydeog9486]

@@slengineeringacademy2234 my inspiration bless up

[@Rawalamit13]

Direct ac or its required dc adapter for light ?

[@yousifalqallaf8095]

Will it be short if both sensors triggered at the same time?

[@slengineeringacademy2234]

No. Thanks for watching.👍❤

[@yousifalqallaf8095]

@@slengineeringacademy2234 Thanks a lot for the fast reply. Subscribed!

[@masan.elkteryk6296]

Ok🙏

[@belitigar82]

whether 3 motion sensors can be connected

[@Axtrible30]

It is available in online?

[@sandravisser8450]

Where can you get that motion sensor switch?

[@jamessnipes2736]

www.amazon.com/gp/aw/d/B019IEYMKM?ref=ppx_pt2_mob_b_prod_image

[@muhammadyounus7143]

Nice sir kindly tell which software you used for animation i need this for my uni presentation

[@oserebright6505]

Hello still very much waiting for to reply this. I also need it

[@RabbleTBabble]

Series or parallel?

[@roryboettcher7862]

How are you powering this set up?

[@richardfarrell362]

I believe the NEC required a minimum level of light all the time. So the lights can never go completely 100% off

[@luiddypollock7182]

How do you call that specific type of motion sensor?

[@sukumarannair8337]

Available in Amazon and flipcart

[@syedkhaja1719]

Is sensor ko wall me fit kaise kare

[@mintu4211]

Can i used led strips?

[@slengineeringacademy2234]

Yes you can. But additionally you have to use AC/DC LED Driver. Because LED stripes are worked from DC current.

[@maniwater4937]

Any light apply diss led light??? Plz tell me bro

[@slengineeringacademy2234]

You can use 230V resistant any light

[@MeYou-ln9cm]

Plz.list of components.thanks

[@slengineeringacademy2234]

Plz watch the video.. I have explained all components.

[@Wolf-rg7ih]

So confusing Just run a 12 3 cable. That’s all