Startup Process on Delta's VFD-M Series AC Drive

[@teranteran4909]

Went the display does not turn on

[@jwiqbal]

What does display Lu means... Motor stops instantly after starting..

[@LongNguyen-kq5ho]

hello Galco tv, every morning i turn on my VFD-M 1.5 kw, it always display this erro, f-03. but when turn off then turn back on, it's ok, working again, is my VFD going bad? please advice, thank you

[@electricalengineeringmachi2923]

dear i am facing problem in Delta VFD M drive.0.75kw, there is Error on display CF3..i cant press any button,bcause CF3 blinking continuously, please recommend solution.

[@kamranhossain7992]

I have a vfd-b delta but when i start this inverter it will run for 3-7 min then show occ Please tell me how can i solve this problem

[@mdarifurrahman824]

Can u help how to control full meter ???

[@clamboni9]

Need help, got parameters from machune manufacturer. I just went down the list without paying enough attention. Gor to number 76, put in 08 like the list said........then realized after it was too late that this was the parameter lock. Now i can't wnter the rest of the parameters. Is there any way to unlock or reset it? I cant find anything in the manual.

[@GalcoIndustrial]

If this drive is under warranty you should talk to your supplier first. They can can help you with the drive or contact information for the MFG. Have you tried to use some of the parameter values for the pass code to unlock it? Most drives let try until you get it.

[@clamboni9]

@@GalcoIndustrial yep. It wont even let me cycle through the numbers at all. Thanks for the reply.

[@lakshmansiriwardhana5595]

How can we buy a control unit

[@alwaysyourattitude7678]

How to increase f8 take drive frequency

[@arif-me]

I got a problem, I don't know why doesn't star motor? There is no p option, only F .

[@GalcoIndustrial]

Try applying the "5 rules of drives", (AC or DC drives). 1) correct line power is on, 2) motor is connected properly, 3) start command present, 4) speed command present, 5) is there feedback required? let us know what you find.

[@mikefreedom5612]

Do you ship Delta VFD to Canada ? What means 1/3 phase?

[@jieliangchua3196]

Basically means they have either single or three-phase drive

[@atruebiblicalchurch]

How can I do a factory reset ?

[@GalcoIndustrial]

Very good question, go to parameter Pr.76 "Parameter Lock and Configuration". Select #9 or #10 to reset factory defaults for 50Hz or 60Hz respectively.

[@GalcoIndustrial]

www.galco.com/techdoc/dlpc/vfd007m43b_um.pdf

[@atruebiblicalchurch]

@@GalcoIndustrial Thanks that did the trick.

[@atruebiblicalchurch]

@@GalcoIndustrial Are these the right parameters for 1.5kw Delta VFD-M for your CNC router P01=02 P03=400 P04=400 P17=400 P18=350 P19=300 P20=250 P21=200 P22=150 P24=01 P52=60 P64=00

[@intereatingthinginlife167]

need help please i have the VFD-M it indicate o c A ( or o c R not sure) what is the problem

[@GalcoIndustrial]

Is probably OCA or Over Current during ACCEL. Try increasing the ACCEL time if you haven'y already. If motor doesn't even turn before fault occurs you may have an issue in the power section of the drive itself. Try disconnecting motor completely and see if still faults, if not may have an issue in the motor or wiring. If it still trips with out any load the drive is most likely bad.

[@mdanascnc5584]

wiring problem

[@arivazhagang2309]

What is the meaning of P01,P02,P03....

[@balveerbalveer2652]

RanNahin le rahi hai Karan batayen

[@Sharaddadhich599]

vsc100-or75g-s2 0.75kw drive parameter help me

[@darshanpatadia9579]

What is the direction of cooling fan in vfd-m up to down or down to up airflow!!

[@thakorjagdish8759]

Pushbotan start stop connection in the drive please

[@GalcoIndustrial]

www.galco.com/techdoc/dlpc/vfd007m43b_um.pdf

[@GalcoIndustrial]

Follow this link for a copy of the user manual, page 2-2 shows all the interconnect to the drive.

[@tirupatiraosirela7600]

Please explain telugu language delta ac drive 200

[@rachelpowersyatem3078]

CF3 (hardware circuit fault)

[@GalcoIndustrial]

Sounds like the Control board has developed a fatal error. You will should return it to your distributor or the factory for repair or replace, depending on level of damage they find in it.

[@thakorkishan1758]

Nice bhai

[@المغترب-ط7ز]

عندي مشكلة

[@المغترب-ط7ز]

VFD series 022E43A

[@rokingkiranl]

Thank you

[@GalcoIndustrial]

Welcome

[@alwaysyourattitude7678]

Please video

[@RohitKumar-wl3ul]

Rohit Kumar

[@vijaykumar-je6tr]

Vijay Varma

[@upendrasingh185]

Hinde me

[@GalcoIndustrial]

क्षमा करें, हम वर्तमान में केवल अंग्रेजी और स्पेनिश में पोस्ट करते हैं

[@nicom3536]

ขอเป็นภาษาไทยได้ไหมผมฟังไม่รู้เรื่อง