Tap to unmute

Steps to diagnose 3.3v and the 5v

  Рет қаралды 12,311

Jbv Technologies

Jbv Technologies

Күн бұрын

Пікірлер: 11
@laptopDoctorKZN
@laptopDoctorKZN 7 ай бұрын
Options b. Inject 0.7 v @ 1 amp on any inductor. If voltage drops and amp raise. The you found the shorted rail. If all are OK. The inject 0.9v at @1.5.amp on current sense resitor If voltage drops and amps raise then u know the short is on 19v rail to. Then go t Bq chip. Check 6v @ regn pin 2.4v @acdet 2.4-2.7 @acok. The check. 1st and second mosfet gate voltage should be 6v greater than charging voltage . If no 6v at regen pin then 1st and 2nd fet won't allow 19v to pass to current sensor
@chathuradesilva48
@chathuradesilva48 3 жыл бұрын
I hve lot of things to learn from you... thanks again
@younisanwar3762
@younisanwar3762 3 жыл бұрын
keep going you will earn money ASAP Hope so ! I have some question. How could I get touch with you ?
@anagodoriane8778
@anagodoriane8778 3 жыл бұрын
Please share the e-book link
@jamesnagib9141
@jamesnagib9141 Жыл бұрын
thanks alot keep it up (:
@laptopDoctorKZN
@laptopDoctorKZN 7 ай бұрын
Steps to check with out long story's. 1. Multimeter on ^ beep mode^. 2. Black prob on ground. Then Option [A] Place red probe on all solder joints marked ^JPF^. if it beeps and ohms close to 0. Then de Solder there. TEST each side of the ^JPF^ joint see wich side beeps or had low ohms. Follow the pad and see what the rail powers. Jpf split Pad away of coil is towards the Rail.. Towards coil is the vrm. Inject 0.7 v .. -> use thermal camera, Rosin flux atomizer, ,spray ipa., check close what gets hot. Replace. Part if possible. Or remove the cap. NEVER USE DC BENCH ON 19V RAIL.. DO NOT INJECT IF YOU HAVE NOT DISCONNECTED THE ^JPF^ POINTS AFTER THE COILS. IF High side fet short on any power rail section u will destroy the board. Inject 0.7v on 19v rail is safe.
@josepeixoto3384
@josepeixoto3384 3 жыл бұрын
too bad the sound is just too low,can hardly hear
@jbvtechnologies
@jbvtechnologies 3 жыл бұрын
Sorry my bad
@johnmaloma7623
@johnmaloma7623 Жыл бұрын
Do you always switch bench power supply to 19v, even if we test 3.3voltage and so on?
@martinharmath1566
@martinharmath1566 9 ай бұрын
your explanation is too difficult
Laptop Motherboard No Power - Troubleshooting Short circuit - Fixed!! - Part 3
24:24
Electronics Repair Basics_ERB
Рет қаралды 34 М.
How you can diagnose a faulty SIO/EC/IO/Startup shorted chip
14:06
Electronics Repair School
Рет қаралды 41 М.
This is how you confirm if the GPU or CPU is shorted
17:08
Jbv Technologies
Рет қаралды 29 М.
How Laptop Capacitors work - Ceramic capacitors
27:54
Jbv Technologies
Рет қаралды 6 М.
Important! Steps to diagnose a faulty laptop
21:13
Electronics Repair School
Рет қаралды 70 М.
Learn to Check 3V and 5V voltages on Laptop Motherboard - All about 3V 5V Circuit
12:35
Electronics Repair Basics_ERB
Рет қаралды 9 М.
This is how you repair a laptop by not jumping a mosfet
27:05
Jbv Technologies
Рет қаралды 43 М.
How to Check 3VALW and 5VALW Circuit on Laptop Motherboard With multimeter
16:35
Electronics Repair Basics_ERB
Рет қаралды 4,3 М.
lenovo no power fail
13:28
Jbv Technologies
Рет қаралды 1 М.