Very few people know, the secret of the welder is making precision 90 degree joints on square pipes

[@dandeeteeyem2170]

Don't know why so many people are commenting about how they already knew this... Why come here? 😂 The video describes a common mistake, which is overcome by doing something counter intuitive. I remember many, many years ago thinking I just wasn't cutting close enough to the corner 😅 great video

[@Ronsreypich]

are you mean?

[@dandeeteeyem2170]

@@Ronsreypich I was genuinely thanking the dude.. But yes, I am average, if that's what you were asking :P

[@seanbryers29]

Thanks for this video i learned something new 😊

[@jeffwells4072]

Can someone please explain the difference in the first and second cut. I see the little line he made but the cut looked the same

[@tdentertainment8768]

Khác nhau hoàn toàn, lần thứ 1 cắt sát mép. Lần thứ 2 cắt bỏ 1 khoảng nhỏ ngoài mép.

[@codygallik2261]

The music set me straight into a wonderful mood. That was good.

[@WELDING_INDO]

trik yang sangat sempurna sekali bang inspiraasi dalam segala hal

[@idetubeid]

Thank you very much 🙏

[@romellyarde907]

i didnt see where the measurement for material thickness was measaured in and used can you tell me i am lost?

[@NoNo-dq4mc]

Cut it thru at 45, flip one side 180 degrees, chamfer your edges , butt weld. It is faster.

[@dwaynelejeune3508]

You show lot of tips/tricks on cutting angle and square tube metal, what about cooping round pipe

[@wellnesslifecaresolutions3511]

Great.. Thank you so much

[@nimrow99]

Thank you, I benefited from your beautiful ideas and wonderful videos🌹

[@Mightiflier]

Am I the only one who is almost counting out, 123123123123123 at the beat of the music while watching this video?

[@Mightiflier]

Something about the whole thing is relaxing and rewarding.

[@jorger.m.j.7494]

Me too, I'm going to put that topic when I have to do some work....and for crafts or drawings I recommend the following one. m.kzbin.info/www/bejne/qZqmnqSsm9ySZ8k

[@jdcmber]

Thanks!!

[@ASMguitR]

This is not a secret. Very many people know to account for wall thickness, including all professional welders. But useful for those starting out.

[@Mightiflier]

Very helpful info to that group, which was a secret to them

[@seanbryers29]

I did t know this

[@nowsadhossain5426]

Thank you for such a beautiful video ❤❤❤ I want to see more new videos like this ❤❤Thank you for such a beautiful video ❤❤❤ I want to see more new videos like this ❤❤

[@INDOWELDER]

Good job bro ❤️👍👍

[@masterQ20]

Thanks for sharing. God bless you 🙏

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@ma-lakshmifabricator7549]

Overall, this is a highly informative and enjoyable video for anyone interested in fabrication. It showcases your talent and expertise while providing valuable insights and inspiration to fellow enthusiasts. Keep up the great work, and I look forward to watching more of your content in the future 👍👍👍

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@apk9357]

Thank you so much

[@mranil99]

Thanks 🙏🙏❤

[@veeramuthus581]

Thank you❤

[@iiscantik4721]

Kebangetan manstabbb bang.. 👍👍👍👌

[@dianavergara5652]

boss gudeve anu po ang sukat ng pinaka makapal na tubular

[@jimsmith8071]

So, you made a nice joint in the middle of the tube. What are you going to do on the other two ends of the tube? What is planned final product you are making?

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@rcytb]

Wouldn't "leaving the line" (cutting inside the lines) accomplish the same thing?

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@Ernie-Tech]

Yep, nice vid but too bad that the cutter didn't run the edges of the cut metal down a bit just before plying the corners together. This would make the welding easier since a gutter-form is created and so the welding penetrates better. Spoken comment misses, this makes understanding so much easier.

[@SaeedSaeed-vt6om]

Cool work thanks 👍

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@Jigsofficial16]

Nice thanks for sharing this video bro❤

[@azwanpalugada3842]

Terimkasih ilmunya...👍

[@rafaelmolina123]

Can this be done on a c channel bar?

[@mdsarfaraz9469]

Good work

[@ArvInd-vd2ww]

I did not understand a thing about what he did. Just by drawing a line the cut became perfect? I see no difference between the first cut and the second one. Can anyone explain to me what he did?

[@CinDeihLian]

Good job 👍

[@totoy33]

재관의 달인 재관의 기술자. 최고입니다 👍🏾👍🏾👍🏾

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@curonelectricity]

I like your video ❤❤❤❤❤

[@psee919]

Nice 👍

[@semiproapologizing7622]

I dont see the difference at least you just cut all through the top triangle

[@XavierLENOZACH]

tres pro merci

[@จ๋าชาวไร่ทํางานหาเงินทุนกลับบ้]

เยี่ยม

[@snowwarden3711]

so instead of a point we have 2 points that r the thickness apart?

[@AlekseyKrigin]

Я тоже так делаю, первый раз не правильно, а потом правильно.

[@Сергей-ф5з6п]

Покажи как из отвода 90 сделать угол 37 градуса.столкнулся на работе

[@LeoA-t4z]

Dijeran en mi rancho, no pues chido 😂👍

[@edemoi3817]

This ai known But good work.💪🤩👍

[@danieltrombeli6610]

Show de bola

[@vanhuynguyen9124]

Exactly

[@JohnnyHarness-e9t]

Did anyone see the ants fighting on the table.

[@fernandoparcel]

De que medida es el metal

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@johnhiggins2685]

Ha ha. I laugh at all the comments on here. Everybody finding faults. Ok here's another one. Would it be better to put a full penetration weld on the first one, rather than just spanning the joint on the 2nd😅.

[@michaelfernandez7237]

So whats the trick

[@ohhansel]

If you're going to be teaching people, how about teaching them to work safely ? Where is your guard for that grinder? Just look up pictures on the internet of people who didn't use a guard. When that wheel shatters you're going to hope there's a guard on there.

[@T.M....]

I agree. See it all too often, these channels disregarding safety without a guard. Just comes across unprofessional and cheap.

[@mikedillon9080]

That's because guards are for people who don't know how to operate a grinder. He knows how to operate a grinder safely but needs only cut 1 45° and flip the other piece and avoid wasting time & rod filling that huge gap

[@quaidq4771]

Guards are worthless and slow you down

[@adamnieuwhof3463]

Gaurds are there for a reason even if you know how to use a grinder you can still break a disc people make mistakes and if you have to take the gard off to get in somewhere your using the wrong tool

[@edwindol3597]

​@@T.M....obviously never used a grinder professional nor spend time in a shop full of professionals who work daily with grinders lol

[@davidspencer6557]

Buy a cheap chop saw,

[@MalaBi-l9e]

Je veux souder

[@txxr542]

Those tricks are for small projects. I haven't seen video where some welder can improve more in the 45° cut. This wasn't helpful at all

[@NextBangkok]

👍👍👍👍👍👍♥️

[@ewaspirydowicz4561]

Super Super Super komentarz 👍. 🇺🇦

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@MaryJaneYagao]

❤

[@بهاءحلووم]

👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻

[@walterdiaz2989]

😂😂😂este todavía no aprende usar las herramientas y quiere enseñar. Era tan simple como dejar la marca te comes la línea que hiciste con el lápiz. Aprende a usar las herramientas primero después te la das de profesor

[@gpena383]

😂😂😂 I rather have a gap for welding.

[@richardbart8256]

What a load of crap. Anyone can work that out but anyone with half a brain will see it's much quicker and easier to chop it once and deal with the extra but of welding.

[@hidupenak99]

Like & Subscribe 😊

[@หนุ่มเมืองสิงห์-ธ1บ]

ในคลิบก็ยังไม่ถูกนะใบลูหมูบางแพงมากตัดได้ไม่กี่รอยถ้ามีพาสม่าเล็กประหยัดกว่ามากในกรณีงานที่ทำเยอะจำนวนมากใช้พลาสม่าเร็วกว่ามากและประหยัดเงินกว่าส่วนใบลูกหมูเล็กเอาใบเก็บงานลบคมถ้าลบคมจะได้หลายงานมากตัดเฉพาะงานที่จำเป็นจริงๆผมเคยใช้ตอนสมัยเรียนเทคนิคอาจาร์ยให้เปลี่ยนมาใช้พลาสม่าแทนส่วนลูกหมูเล็กไว้เก็บงานใบเล็กๆใบเดียวใช้ได้เกือบครึ่งวันตอนเอามาตัดแบบในคลิบตัดไม่กี่รอยก็หมด

[@igorberezin856]

I do it my way and never have to measure pipe thickness and it comes out perfect. I dont know what your problem is buddy

[@FRANCOISPOOLMAN]

Scroll by please I wanna watch and learn😢