Stitching on a Richardson 112 Hat: Easy Breezy

Рет қаралды 1,809

Күн бұрын

Пікірлер: 31

@aldel3342 10 ай бұрын

Looks great stitched out on the black Richardson. Plus the Candle thread pops and the digitizing was so smooth. Mission accomplished.

@RomeroThreads 10 ай бұрын

Yes, and in person the hat looks even better, Thanks Audrey!

@migsrome1022 10 ай бұрын

amazing work !

@JoaoPereiraEmbroidery 10 ай бұрын

Great content as always 👌🏼

@bridgetgainous5487 10 ай бұрын

That looks fantastic!

@RomeroThreads 10 ай бұрын

Thanks!

@jessiegibson9023 10 ай бұрын

Good video thanks looks good

@RomeroThreads 10 ай бұрын

Thanks Jessie!

@donhatter159 10 ай бұрын

I love this logo of college football team

@cali_cal 10 ай бұрын

looks great! might have you do some of my stuff 😀

@tmgcustomdesign8689 10 ай бұрын

How do you like the Tajima? Did you also stitch out the file on your MT1501 to compare it to the Tajima stitch-out?

@RomeroThreads 10 ай бұрын

Thanks JR. I didn’t stitch it out on the Ricoma, but I am planning on doing comparisons soon.

@UnKnown-jp1bv 10 ай бұрын

Yes, Id like to know this as well...I hope you didnt divorce your "MT-1501 Family", with your New Nice Fancy Tajima 😂Looking Sharp. Thanks for the Vids! 😁

@aldel3342 10 ай бұрын

Can't wait to see the machine comparison. Hope you do a few videos on the Tajima including setup.

@johndoeee888 10 ай бұрын

Any pointers on embroidering on a 6 panel hat. That front center is tough haha broke so many needles. And suggestions when embroiderying on that parr?

@RomeroThreads 10 ай бұрын

My only pointer is to use a 80/11 sharp needle. I did not have to do anything special.

@maniakDna 5 ай бұрын

Small letters are the problems I see people complaining about the 112

@Dixie15 10 ай бұрын

I bought the Gen2 system for our Richardson hats from Ricoma. It leaves teeth marks on all of them where as the Ricoma hat hoops don’t. I even sent off for a replacement and it leaves the same marks as well. Does yours do the same?

@RomeroThreads 10 ай бұрын

It’ll leave teeth marks if the teeth’s are not inside or close to the brim. It needs to be tightly inside.

@themovieandtvstore5318 10 ай бұрын

Would be good to know the needle size, do you steam the cap and what speed did you run this at?

@RomeroThreads 10 ай бұрын

Im using a 80/12 needle, ran at 600 spm and I didn’t have to do anything special to the hat.

@sunrisetacticalgear2676 10 ай бұрын

How fast did you stitch it at? What size needle did you use? It looks Great!

@RomeroThreads 10 ай бұрын

Speed 600, needle: 80/11 sharp

@sunrisetacticalgear2676 10 ай бұрын

@@RomeroThreads Can you push your new Tajima harder to see if the stitch quality goes down? I recently did 48 Richardson 112’s with 9346 stitches of a badge type design, with a center placement at 820 SPM using 75/11 titanium needles with large shank. I did have to change needles around every 8 hats because I could hear it start to hit harder as it got dull. My guess is that your new machine won’t have any problems, that’s the benefit of this brand over your other machines. Thank you for your content! My examples were run on my Barudan Pro3’s.