STOP Buying the WRONG Air Conditioner Brands (2024)

[@chrisbardwell2533]

I have 46+ years in the business, there are slight advantages to brands. The main issue is and always will be the installer. Good installation practices will extend the life and performance every time. A clean, leak free, evacuated system with no short cuts will out perform a poor installation every time.

[@callmebigpapa]

More or less that is what Consumer Reports said. The top few brands were statistically insignificant in their problem rates.

[@Whodafuqcareswyt]

So true

[@HeatGeek1]

@@callmebigpapa I no longer trust consumer reports. They rely heavily on consumer surveys instead of individual product testing and teardowns like they used to. I do agree with the basic premise of install quality being a key element to good results. You can pick a top brand and get a poor quality install and have absolutely dismal results. It's equally true you can pick what people regard as a bottom tier brand with a stellar install and have a long happy service life with better comfort.

[@callmebigpapa]

@@HeatGeek1 I'm pretty fortunate that where I live we use package a/c units and I've been told these are more reliable because they're totally built in the factory and no lines have to be hooked up on site is that your experience also if you work in this field?

[@HeatGeek1]

@@callmebigpapa in general I would agree that factory braze joints produce fewer leaks, but it's also important to remember that refrigerant leaks can happen anywhere, and I do mean ANYWHERE inside the system. One key problem with package units is the equipment and at least some of the duct work is outside the thermal envelope. That's a big hit on the efficiency of the system. You always want to have all the furnace, evaporator coil and ductwork inside what we refer to as the thermal envelope or the insulation layer of the home, otherwise it's a needless waste of energy.

[@andydelle4509]

What about Goodman? Most dealers consider them junk. I have two Goodman's, one 20 years old and another 14 years old. Looking inside we have: 1) A Copeland compressor. Copeland is a major and respected compressor manufacture. 2) A GE condenser fan motor. Nobody ever accused General Electric as a poor choice. 3) The coil is all copper with aluminum fins - easy to repair a leak. So what exactly is junk about a Goodman? The sheet metal housing? The easily replaced $25 capacitor?

[@kurtzimmerman1637]

every time I take my goodman condenser apart to clean the coil, it takes forever to put that POS together because it's flimsy as hell! buy rheem or trane.

[@jeffa847]

I have 2 Goodman furnaces and AC units in different buildings that are 25 years old. They haven't been much trouble. Couple small problems that were cheap to fix but of course it is always a hassle and stressful when you're not an HVAC tech and the furnace doesn't start on Wednesday evening before Thanksgiving at 5:30 PM as the temperatures were supposed to dip to the single digits haha. That was 10 years ago and I fixed it for nothing (after paying an HVAC guy $95 to not fix it) but like I said - stressful and time consuming. Overall though I would consider going with them again given that they have done well and weren't expensive.

[@castirondude]

I used to have a Goodman package AC with gas (propane) heat and it worked well for me. Sold it with the building. The propane was quite efficient, the exhaust gas was not very hot.

[@davidsmith385]

We had Goodman installed on our house, leaked the first Summer, finally replaced the old one with a bigger unit because the old one would not keep up. The service man who installed the new one was independent, he did a great job with installing the new unit, great results.

[@CryptAFO]

Pretty much every brand except Lennox (which is proprietary) uses the following parts brands in their units. Copeland/Tecumseh compressors Mars/Honeywell/Supco relays Honeywell gas valves Emerson/GE motors Johnson control/ Mars/ Penn pressure switches GE/Eaton contactors Goodman is no different.

[@Shahrdad]

I had a Lennox system for some years and it was nothing but trouble. It broke down all the time and never really worked properly. I replaced both units with American Standard, and it's been outstanding so far. The same installer installed the system, and they told me they stopped carrying Lennox because of all the problems they had with them.

[@jay3660]

My parent’s house had Rheem AC . It was installed in 1968 ane the same unit is still going strong. 54 years, wow.

[@DSC800]

Wow, that's gotta be a record. I just sold my rental house, built in 1979, with the original package unit (on the roof) still going strong. I think it's a Carrier. I only serviced it about every 5 years. Home inspector said it was still working great.

[@JasPlun]

@@DSC800 Next door just replaced a Rheem from the early 70's with a Goodman. I would have baught another Rheem after that kind of service lol.

[@fish4fun354]

I hope the Carrier in my house still keeps doing good from 1998.

[@JasPlun]

@@fish4fun354 Like with all brands not every single one is bad, you have some with higher failure rates than others that is what they go with. My step dad was a Carrier dealer for years and installed them on countless homes in West, TX. There was a period he ran into where the compressors kept failing at a super high rate so he switched brands to Rheem. Rheem had just come out with the scroll compressor and he never had high failure rates again. That was a long time ago whether or not Carrier got their quality back or not I can't say. The scroll compressor was really good and went on to be a huge success for Rheem. Carrier today might be better than the rest as technology is always changing. I can tell you Carrier is a crap company though they shut down the Plant in east,TX and moved the operations to Mexico and killed hundreds of good paying jobs for the people that lived in the Tyler, TX area. Trane is still in Tyler making units so lets hope they do not bail on the American people.

[@wholeNwon]

@@JasPlun Very different machines now despite the retained name.

[@Snarkapotamus]

We put in a 3-ton Goodman 18-years ago when we bought our house and other than typical things like capacitors, it's been pretty solid.

[@orrinkelso9295]

Over 15 years ago I installed a new Goodman AC and furnace myself. House did not have AC before. It has been working flawlessly with no service since install. I have been very happy with it.

[@LynnNg-np5md]

@@orrinkelso9295 you should be proud of yourself because a lot of people like me don’t know how

[@victorsr6708]

I’v been a contractor for 33 years in California and this young man is 100% correct. Great video

[@flaviosanchez2861]

It depends Houston capital of ac in the world trane claims #1 Ohio solid trane ,Kentucky Tennessee i serviced most brands and American standard the best, confort maker is good from carrier at residential level but I trane is heading the race commercial and residential maybe not industrial

[@orornil1973]

what brand do say for southern California i.e. san diego

[@RamblinRoadies]

@@orornil1973 I'm in San Diego, and I have two Goodman units that are 21 years old. Face it, we don't really run the a/c that much in San Diego.

[@artics1031]

YORK IS THE WORSE QUALITY CONDENSERS THEY LEAK REFRIGERANT LIKE CRAZY

[@evhvariac2]

I’m an astronaut and also like the video

[@RamblinRoadies]

We've had two Goodman systems in our home for 20 years now. They have both been virtually trouble free. At the 16 year for one, and 18 year for the other, I replaced the circuit board in the air handler. It was very easy, and cheap to do myself. I would buy the "budget" Goodman again.

[@ilc-nl3yy]

I bought a Goodman furnace and blower a few years ago and it's been great so far. We'll buy a two stage Goodman outside ac unit when our old one breaks.

[@kennethdurden880]

We installed a Goodman unit in my mother in laws home mind 15 years ago. The only thing I have had to replace is the capacitor and the control unit in the home. I have family members that work at Trane. They have so many units that come back because of leaking coils and circuit board issues is astounding. The engineers have made their high end units so complicated and it's very hard to do part replacement because of the crazy way some parts have been assembled. To their credit though they definitely stand behind their warranty.

[@TeslaBoy123]

Igree goodman are great system work pretty well i own few furnace differents properties for many years with free issues or drama only maintenance every year and nothing else to do

[@allencarroll5565]

My goodman is 30 years old,i have put less than $300 in it the whole time.Everybody says this is worst brand i disagree.

[@5litreho]

My 24 year old Goodman A/C ground units for my house are very reliable. They both have the original compressors!! Only components that failed were capacitors and condenser fan motors. Both air handlers are original as well. Very minimal issues. We've owned the house for 17 years...

[@darkphantom507]

I agree 100% with you on Lennox. Garbage, can’t wait to get a new AC.

[@JohnBowl14690]

What about Train?

[@mac7977]

I had a 5 ton American Standard duel fuel system installed by Springdale. It's been really efficient and has lowered my utility bill. The quality of the installer makes a huge difference also.

[@monteglover4133]

I’m a 40+ year HVAC&R tech/contractor primarily service as others have said most times on the installer. The only air conditioning systems that have an unusual number of failures have been any with “micro channel” coils. I installed Goodman in our current home to replace a 30+ Lennox the home we just purchased has a Rheem system. Most systems appear to last 20 to 30+ years.

[@redbone7040]

My Goodman has been doing good after 12+ years

[@michaelwright1602]

Goodman here too... I like the fact, that if I need parts, they are readily available and inexpensive. Only work I have done on my condenser unit is to install a soft start. 5 years no issues.

[@frequentlycynical642]

My brother in FL had his original AC/heat pump last over 40 years! Don't know the brand and even if so, it doesn't mean the same quality is there today.

[@davidcallahan5157]

@@michaelwright1602 Did you notice a difference with the soft start?

[@michaelwright1602]

@@davidcallahan5157 Yes, I did. How to explain this? That hard bang snap start is now non-jarring, just a nice smooth start, if that makes sense? I can see how this would help with extending the life of the condenser unit. And it was easy to install, a simple nut driver and swapping some wires around. I would recommend getting one, they are inexpensive, and do make a difference.

[@frankb1]

I appreciate your video. We replaced an old AC system with an energy efficient Carrier system a few years ago. They guy who came out to give the estimate (not your company) was very familiar with AC systems and made some good recommendations. I had a lot of confidence in him. Fast forward to the installation and that guy was nowhere to be found. The crew that came to install the system was the B Team or maybe the C Team. A bunch of 19 year old knuckleheads little experience who made numerous mistakes that their supervisor caught and some that I didn't discover until after I signed off on the installation. One example: sealing with silicone parts of the furnace/blower unit that were not intended to be sealed, such as the filter access area. I learned a lesson to make sure the installers are as good as the salesman.

[@Jay-bw3fl]

Yep a lot of companies send the nice knowledgeable man to make the sale and then send the retards to do the install. Mr roof is one example who got me.

[@6barry66]

What is wrong with ceiling the blower area with silicon. He did that so hot attic air Or damp basement air Doesn't leak into the unit. He did you a favor thank him don't criticize him.

[@hokehinson5987]

Wow! Your experience is duplicated by a very prominent HVAC company here in Central Florida...weekly....corners are cut that favor the company, even when those decisions violate building codes & endanger the customers. Mistakes are hidden or covered up. Installs are very unprofessional & the long term employees continue with poor work quality & are not open to redirection or updated training. Several older techs have poor electrical skills and have been known to install breakers above line amperage rating. The installs are like companies did back in the 80s. Yet this company is very rooted within their sphere of influence...has deep pockets & friends in high places and a gang of attorneys covering their asses. They hired a very talented HVAC Tech who was supposed to be a roaming fld manager to inspect installs, offer suggestions & return a week or two afterward to address complaints or settle customes needs with thermostat training. The old blokes in the field were insecure with him, rejected his suggestions & Generally refused to accept his authority & isolated him. The old long term blokes are good ol' boys in the work force dating back to the original owner...the family members now running the show only care about the bottom line. They look the other way as these rogue techs run the show. The new guy basically does customer complaints which are many including threats of civil suits for basically installation malpractice. This tech was easily intimidated by the sales staff who make 6 figures a year being coerced into doing much of the electrical engineering work instead of using the electrical contractor normally on call therefore saving cost for the company while padding the profit for sales commissions. It's truely amazing how an old standing company such as this one can remain in business with this level of mismanagement but they pretty much corner the market in HVAC and propane sales having started many years ago as fuel oil suppliers...and in hard times as weed control service spraying kerosene on city side walks and vacate lots. And yes the young techs they hire stay in school long enough to have skills but through abuse learn poor work standards and finally get around to taking state exams. The bottom line is money,money, money! In America a business license is just a license to steal...theft has many levels. And in florida when ya find an A/C tech who will actually repair instead of condemning your system because of a $25.00 Cap or contactor switch or condenser fan motor is a pearl of great price to be cherished....

[@hokehinson5987]

@@6barry66 Thinking you misinterpreted the situation ... The 19 yr old knuckle heads silicone the access to where the filter is located. The owner would've been unable to service the filter with such a condition. ..

[@wholeNwon]

@@hokehinson5987 This is not at all surprising.

[@JJ-ec4cq]

We had a GOODMAN ac unit for about 17 years and still running strong 💪!!

[@gussalas2866]

my goodman lasted 16 years

[@peterdarlington4117]

I’m a hvac contractor in Florida and I make good money working on Goodmans so keep buying them please! 😂 and comparing any air conditioner brand from 16 years ago to today is apples and oranges. Goodman is trash today! So is Trane you want a ICP (Carrier, Payne, GrandAire) or Rheem/Ruud.

[@MrDeviousdom]

That doesn't mean anything! Equipment was made differently back then.

[@MrDeviousdom]

I have found that Trane it's actually one the most unreliable pieces of equipment out there. I was a dealer for years and had to stop due to the poor quality, insufficient testing of new technology and extremely high failure rate. Goodman, I would never consider installing a Goodman unless the customer is okay with a 60-day labor warranty. I've had extremely good luck with the Ruud equipment.

[@peterdarlington4117]

@@MrDeviousdom Trane used to be number one and we were the top train dealer in Florida. Once they were bought by Ingersoll rand nothing but trash would never sell one again!

[@prun8893]

Carrier/Bryant paid for me to go to the Indy 500.....tickets, hotel, airfare, factory tour (pre-Mexico), catered dinners, transportation, a lunch cooler with a few Budweisers for the race itself. Then they moved to Mexico and no more Indy 500.

[@ckelly5141]

I live in Quebec, Canada and my Carrier a/c is operating nicely in year 22. The only repair was a capacitor replacement a few years ago. My furnace is a Goodman....about 12 or 13 years old with zero problems. Great video!👍

[@brownro214]

Glad you made the disclosure at the beginning. After the ending recommendation was a foregone conclusion. We have Carrier on our current house and would not use Carrier again. We have had a number of repairs both in and out of warranty and have had our technician relate that most of the problems are known to Carrier but instead of notifying customers they just let it go until the unit fails. One of the failures was so common the technician knew exactly what it was from my brief description of the issue.

[@jsfbay1]

Can you tell us any more about this? Which Carrier models? Have Carrier Infinity in our house and so far so good, but would like to know ahead of time if we have the same models.

[@BigPairOdice]

Likewise, with our Carrier Infinity system. Never again will I go with a Carrier HVAC system!

[@EarlHayward]

I installed quite a few Carrier/Bryant in the 90s and early 2000s when I was a tech and service manager in Phoenix and never had issues.. I did a couple Carrier Infinity units around 2014 for a friend and they worked great and air have never even received a call from him about the unit and we still chat today… Although, Goodman has improved as they used to be noisy as hell due to thin steel and poor construction… But now, for the price, a decent budget unit… However, American Standard is my goto for mid-line as their incremental cost for more efficient units is the best value (or used to be), similar to Bryant…

[@TheWaterbouy88]

As an HVAC contractor in Florida, this video is an accurate source of information.

[@USCavalry1]

Thanks dude

[@Dan-vb3ju]

@@USCavalry1 bullshit

[@gamingwithmr.fregles8802]

36 year old house, still chugging with it's original Payne 1 ton package unit. Only had one breakdown, but it's chugging strong.

[@16B9]

I've had a three ton Coleman heat pump for 35 years in my 28' X 56' manufactured home. I've replaced the outside coil once and the A coil inside once. I live in Yakima Washington and have hot summers and cold winters. I have a Jutul LP heater in the front room plumbed to a 500 gallon LP tank for heat backup. We are pleased with our setup experience. Thank you for your overview.

[@jacksonfl]

Greetings from Jacksonville Florida USA. Two years ago, we installed a 5-ton, high-end Goodman A/C-heat pump. No problems, so far. All of the maintenance men say that they like Goodman units, because they are straightforward and use mostly generic parts that they can get quickly. When that subtropical sun is beating down, you don't want to hear that what you need is on back order! They told unhappy stories about Carrier, Trane, and especially Lennox on this score. So-called premium might not always work out better.

[@edbouhl3100]

Parts - agree that’s a big concern. Especially with electronic supply chains not looking as reliable as 5 years ago.

[@keithnoneya]

In Slidell, Southern Loisiana, my Goodman CK49-1B, R-22 unit, lasted from March of 1996 to July of 2022, 26 years 4 months, I'd say that's a good run. It ate Run Start Capacitors like candy but in all those years I only put about two pounds of refrigerant in it and Caps that's it. No start switches, no boards nothing, just caps and R-22 and cleaned the outside coil every year and the inside Evaporator once. Thanks for sharing. Best Wishes & Blessings. Keith

[@johnny_blades]

Just had a premium Trane 5 ton 18 seer variable speed system installed here in Southeast Texas. Simply amazing!

[@DIYAroundTheHome]

That had to be a pretty penny

[@video99couk]

We've had seven Daikin units installed in our home in the UK for about four years now, and had them serviced as required. They have been excellent, quiet and reliable. Really impressed. They work as heat pumps in winter for cheap heating as well as A/C in summer. Yes, homes in the UK can have A/C.

[@SPFDRum]

Do the come with umbrellas? LOL

[@dann547]

We have 2 Daikin units in our home in the Philippines. They have been trouble free and have survived typhoons, earthquakes and a volcanic eruption. Daikin is a popular brand in the Philippines.

[@richard2co]

I live in Colorado and had a new Daikin AC and furnace installed 3 yrs ago. So far so good. The AC is quiet and the circulating fan has something like 56 speeds. The fan adjusts based on the house temp. We had a Lennox before that worked fine for 18 yrs but I thought we needed to replace them with more effecient units.

[@suzukisentinel9570]

I installed a HEIL back in 2015 after lightning struck the house and fried everything. It has a been a great unit. I change the filters every 2 months or so and clean the compressor coils twice a month.

[@donbakos2567]

Ditto Chris. The installation is the key. I put my first A/C in my home Back in early 80s myself. It was running fine until change out, I actually bought it from Sears. I changed it out for a Goodman heat pump 4 years ago, It is running Great. I am FAA Licensed Aircraft and Jet Engine technician and have always paid attention to detail. Actually for me I find HVAC to be quite straight forward and fun. The main reason I do my own HVAC is a few years ago I talked to a couple "Licensed HVAC techs" for a quote to install my first A/C. I did my homework and found they were blowing smoke up my ass. So now I do it myself. Just like aviation, attention to detail the right procedures and tools and pubs are key. And before I forget KZbin has a wealth of information.

[@allenung6260]

What AMM did you follow?!

[@johngatsby1473]

Dude!!! Exactly my situation. These clowns came out and quoted me $8000.00 for a 2 ton install, mind you at that time I was looking to replace around 9 units to start with. Do the math....I wasn't having it so I hit KZbin and learned what I could and then bought a Goodman unit for 1850 delivered and filled ...hired a tech to do it as a side job and then had him sit and watch me and tutor me though the job. I've done 12 now and still need to do quite a bit more. Fukem

[@wholeNwon]

You're absolutely right. There is only one correct way to do an installation. I haven't watched any YT videos on the subject but should, I guess. If done meticulously with proper evacuation, testing and charging the result will be a reliable system. The DON'T let anyone touch it...no attaching gauges ("measuring charge"), etc. When functioning correctly, just like your home refrigerator/freezer, no one can make it function better. It either works or it doesn't. Keep it clean and that's it.

[@nukestrom5719]

Given that you are an FAA Licensed Aircraft and Jet Engine technician, I'm sure you have done a much better job than many technicians do.

[@hokehinson5987]

Nowadays the HVAC schools are turning out junior sales people. Upon arriving in the job market these techs are groomed to dissuade the customer from repairs with immediately condemning their unit. Most folks fall for it...desperate for A/C in the hot humid south. Many a unit has been condemned because of a tri cap or contact switch or fan motor. This trade is open to corruption and deceit too. Years ago I learned how to repair our home A/C system. It is a very simple basic mechanical system. It has gotten somewhat Muddy with addition of heat pumps, solid state boards D.C. motors, variable speed compressors & blower motors. yet a customer can still purchase a basic unit which is strongly recommended. There are thieves everywhere today from the lowly trades person to the politician....Healthcare probably being the worse of the lot. If your a home owner take the time to ask around, speak to your neighbors, friends about a good A/C tech. You will eventually need one if you decide not to be a DIYer...my experience the big blow hard companies that over advertise are like the big blowhard law firms that do the same. You most likely won't be treated well....in America everyone is just a customer...

[@hm5142]

I my son and I installed a Goodman in our house in the fall of 2019. We chose Goodman primarily because it was the one we could purchase easily at a reasonable price. I figured most brands use the same compressors, and that the differences would mostly be workmanship. When we go the Goodman, we were impressed with the build quality. So far it has worked well and we are happy with it.

[@Youtubecansuckmyshithole]

Goodman is trash. I know from working on them.

[@wholeNwon]

IF the installation was PERFECT, they will hold up very well. Copeland scroll compressors.

[@wholeNwon]

@@KZbincansuckmyshithole Starting the 13th yr. with mine and zero issues.

[@picklerix6162]

If installed correctly, the Goodman will perform well. I don’t like HVAC equipment that requires proprietary parts and specialized training to service. Customers will get reamed when the equipment needs to be serviced. Keep it simple. That works for all appliances too.

[@nickdevillo8359]

Love my Goodman dual fuel. Simple, and starts all the time. Going into year 5, great price.

[@SextonHardcastle85]

I’m in Florida and from what I’ve heard, Trane is moving up and Runtru is going to be their builder grade equipment starting later this year. We’ve gotten one Trane increase and another is coming at the end of the year. I agree with your assessment of Lennox. We’ve had so many issues with equipment failures and their constantly fluctuating prices.

[@glengarbera7367]

What a great review. Finally someone who explains the hvac racket. And he's correct about Lennox having problems.

[@Sam-656]

I have a Lennox at my other home. Going strong since 2019 but the condenser is corroded. Poor paint from the factory. I do live 1/2 mile from the ocean, so that's why it's that bad.

[@dtom1145]

in over 50 years of homeownership across three homes in the northeast I have used Rheem HVAC systems (85,000 to 100,000 Btus and 11- 13 SER) and never had a problem. I had/have routine PM every year which makes a huge difference.

[@bossracing3387]

Rheem is definitely the best even right now

[@boydguie8129]

My Rheem AC. Is 30 Years old .

[@stevegordon5243]

@@boydguie8129 My father's Rheem gas furnace and Central Air is 35 years old!

[@eronavbj]

I moved into a newly built home 20 years ago. It had a COLEMAN HVAC system. As far as I knew, Coleman made picnic coolers, so I wasn’t expecting much from this AC unit. Twenty years later and it’s still running well, which is quite meaningful in our hot humid South Jersey summers.

[@johndeerefan725]

All brands are going to have issues, no one is perfect, Installation and maintenance is key regardless of brand you get. That's what I hear a lot.

[@godofplumbing]

Absolutely true

[@KingArtexerxes]

Installers tell you this. I wonder why?

[@johndeerefan725]

@@KingArtexerxes Because everyone pushes their HVAC system over the edge which puts more stress on the system and causes premature failure.

[@Freonleon]

BUY YOUR INSTALLERS!!! The install will make or break your system

[@toddrhine7648]

@@Freonleon So how do you go about buying a honest/reliable/experienced installer in my area? Hmmm

[@thomaslong1576]

We had a new Lennox AC and furnace installed six years ago. Never had any problems with it, and I am very glad we went with Lennox.

[@dwmzmm]

Same here where we live in far west Houston, ours was installed about 4 years ago and as long as the filter is changed (I do mine every 6 months or as needed), we've had no problems with it. We had Abacus plumbing install ours (and remove the old ac system that went out after many years) and they'll come annually to check it. They also (after completion of installation) sprayed insulation in the entire attic, the insulation has worked wonders in keeping our house cool during summertime and warm during cold snaps.

[@rockpadstudios]

Installed mine 7 years a go - no problems. An initial fan unit failure but they fixed it for free. The previous Lennox system in my house ran for 24 years.

[@scottbee501]

I moved to my home 20 years ago. I just had to replace a new capacitor in the air. The furnace and air are 31 years old.

[@Paul-ng4jx]

Yes, this is an awesome brand. Our apartment was built in the 80s and the original guy that built the boys put one of those air conditioning‘s in here the Lennox and it still works perfect to this day. The only thing we’ve ever had to replace on this brand was a transformer five years ago when we first rented the place

[@tyler_russell]

Installed 3 in 2015. All three have broken repeatedly with normal maintenance. Circuit boards, coils, and compressors have all failed. Never buy Lennox.

[@DennisinCLE]

Our Lennox high efficiency system was installed when we built our northeast Ohio home in 1999. No problems in 25 years except with mice nesting in the compressor insulation. We built an addition to the house in 2014. The same contractor installed additional duct work and divided the house into two zones without changing the originally installed system components. Still running well in 2024. Thinking about replacing the system this fall just because of age. The condenser has been cleaned a few times and filters have been changed every six months.

[@dgriffin6074]

Thanks for a very helpful video. Boy was I shocked. About 5 years ago, I looked at all the sources I could find, including Consumer Reports, and then replaced our HVAC with a Lennox Heat pump. We have already had to replace the blower at a cost of about $1000. The Lennox has been no more reliable than the Heil unit in our detached guest house. What a bummer. I saved your video to my "Home" and look forward to more. Live and Learn.

[@C420sailor]

Had a Lennox in my new house. Evaporator coil rotted out in five years, juuuuust outside the warranty. Lennox wouldn’t honor it. Had another Lennox coil installed. It lasted EIGHTEEN MONTHS. Rotted out. I had the whole system ripped out, installed a Trane. It’s been flawless. Love it.

[@tristan2332]

Good to know I have old Lennox and it's 9 years old but I'll never buy Lennox.. Coils are trash.

[@David-xy9yo]

Lennox had a class action lawsuit due to the poor quality of their products.

[@chiensyang]

I have heard Lennox being crap for years. It seemed the company has not changed their way after these times. 🙄🙄🙄

[@David-xy9yo]

@@chiensyang I worked for a company that sold Lennox. It was not uncommon to encounter defective parts right out of the box when you were starting a new system up after install.

[@PCorker]

I have a 35yr old Lennox but AC probably 10-15 not certain. I guess not a new one?

[@markg999]

Got a Carrier to replace a Lennox and so far pretty happy. Brother in law did same a few years earlier than me and happy with his Carrier.

[@wheels636]

Trane makes top of the lne equipment. I should know after working for them for 42 year's. I've had Trane furnaces in my own home for over 25 years now. Zero issues.

[@lp2565]

Great workforce in Tyler,Texas.

[@wheels636]

@@lp2565 I work for the commercial division so I've never been to Tyler only LaCrosse.

[@1Mannco]

I just replaced a 30 y.o. Heil 3 ton gaspack on the roof with the Trane XL16c 3 ton 'packaged' heating and cooling system that combines a high-efficiency air conditioner with a variable-speed gas furnace, 2 stage compressor. Enlarged the intake to 20"x 25" and 18" ducting from 16". I got a great deal, lower than some of the other brands and they extended the manual warranty too. Love it!

[@mattd2503]

I agree I have two trane’s in my house great units .. 👍

[@williammurray8060]

Yeah, but overpriced.

[@jaimesoria5975]

I purchased a Ducane back in 05 and it has never failed me. I had help installing it with a coworker, he too told me that this is a Lennox brand, but I didn't care, just wanted my AC running. So to say that no one should purchase is wrong, unless you owned one and had endless problems with it, but I'm not knocking you at all. All brands fail, some sooner than others, I guess mine was a Tuesday, Wednesday, or even a Thursday made unit, like some vehicles.

[@noelignacio931]

2. Weeks ago , I had a new Lennox installed for my home in Las Vegas , I’m hoping I made a good decision, here in the summer we use our AC’s a lot with days going as high as 110-115 being the norm, I guess only time will tell, but thanks for this honest and informative discussion

[@subvet694]

15 years ago I was a parts manager for a HVAC company in Texas. Goodman had the best bang for the buck back then. Carrier and American Std had the best warranties. Lennox was run away fast even then.

[@paulbernard3929]

We had a new lennox system installed 28 months ago. Furnace, A/C, and heat pump. Never had a heat punp so i was a bit skeptical. Well I gotta tell you, we are so satisfied with the system. The smart thermostat is wonderful, programs so many features, and you never hear it running. It is a propane system, and our propane usage has dropped 40% (approx) and our electric has gone up may-be 10 %. We are way ahead of the $ game. It does need to be checked every 6 months, but I really don't mind it. The system is in the crawl space, I certainly don't want to go down there at 76 y/o. Also had a humidifier installed so the humidity is just right. I realize its still early (28 months), but so far its a great system.

[@bradbyron3620]

Bought our Lennox condensor/air handler/smart thetmostat/zone control system over two years ago. Not a single issue what so ever. Bought thru Costco.

[@Darkk6969]

@@bradbyron3620 We just bought our Lennox system via Costco and will get installed next week. Hope it last a long time despite few bad things said about them. Mostly about coil leaks when the unit is less than 4 years old. I am hoping they redesigned the coils to last longer.

[@sweetmusic3821]

I had a new Lennox installed in 2022. Hate it. DO NOT BUY LENNOX!! I am doing multiple service calls a year to deal with the "smart" thermostat failing to connect (search Lennox thermostat failures). Also I am having moisture problems. The system builds up mildew and bacteria but is not sold with antibacterial strips .... which require a service call every 6 months. The humidity level I set is never achieved...even when it is dry as a bone in the heat of a Dallas summer (July or August). I do NOT see any electricity savings over the previous "inefficient" AC unit. Buy something else.

[@toroscosmicos9889]

Had to replace the Payne HVAC system in our beach house last year. The tech checked the serial number on it and it was 24 years old. It never failed once for us but the AC was fading. Had the same company that installed it back then install a Bryant system. Works flawlessly.

[@JohnSeitz]

Love our 7 year old Lenox 4.5 ton mini split system. Being a 24 SEER system it’s super inexpensive to run in the summer and saves us 200 gallons of oil or more in the cold months.

[@eskieman3948]

Good video! I had two Ruud systems (over a 25 year period) in my Florida home. While they may not have been the most efficient systems, they were tough as hell, and tolerated abuse from idiot service techs (ex, overpressurized coolant to over 400psi) as well as a hot climate up to the day I finally replaced the second unit with a Carrier (impressive system).

[@trustmemysonisadoctor8479]

Hi we replaced our Ruud heat pump after 38 years of central Texas weather, it was a beast.

[@zen-Tii]

We installed a Ruud in 2015 and it’s been a total POS.

[@hamidmazuji]

i wasn't looking for this information, but i'm glad i watched it because it cleared things up a lot. plus, even though the information didn't help me, i have a sister, a rental unit, and a church that i support. so yeah, i'm glad i watched it

[@gregcrabb3497]

I have an Amana package gas unit that was built by Goodman. It's been 22 years with only one repair...one of the spark wires had a break in the insulation allowing the spark to ground itself out. Repositioning and some electrical tape fixed it in 10 minutes. Been working fine for several years since I did it. We had 0 degree temps last week and the house was toasty warm.

[@chrislettenmaier6822]

I have been in HVAC for over 40yrs watching most of these companies be just themselves then merging together. I live in Oklahoma and have found that out of all brands listed the best way to go is middle of the road. Most of those brands have less or no computerized products and handle the stresses of temperature put on them. Most of the top brands are locked out to needing the installer having to program them at setup and those brands only sell to their chosen suppliers and companies.

[@MrHarrySouza]

Incredible longevity! I have an Amana AC installed in 1998, and it's still running smoothly after 26 years-truly impressive!

[@Harry1s]

I've been in the HVAC industry for 33 years and I believe there are 5 things that should be strongly considered when buying a particular brand of equipment and that is; availability of parts, quality and length of the warranty, technical support, and companies with quality and experienced technicians that are available to service and maintain said piece of equipment within 24 hours of a problem. The 4 things I mentioned above are what is important when purchasing your HVAC equipment but there is one more thing that is even more important and that is the quality of the installation. In the end the two things that I have found that cause people the most heart act is the quality of the install and the quality of the service months and years on down the road. How pretty the unit looks, how nice the salesmen is, how the unit operated the first 6 months, and how long the warranty is mean nothing if you have to wait 2-6 weeks to get a part, you have to wait 2 days for a service tech to arrive, the service company sends 5 techs out to repair the unit and they still don't, the unit breaks down 1-2 times a year and so on.

[@cdoublejj]

a lot of us looking this info are DIY, so unless it has a long ass warranty that might not be AS crucial, other wise you are absolutely correct they need god techs but, labor is hard to get these days. plus to me it's toss up any ways. i primarly have worked with Dell over the years and the on site tech quality is a coin toss. what i'm trying to say, is as a DIYer, good parts and design are the most crucial to me. you can have good supply and techs a shit ass system that needs repaired all the time, when in fact it should need little to no repair. same goes for install, needs to be installed correctly.

[@hokehinson5987]

The criminal element is the money men saw the future for profit then legislated laws into place protecting their piece of the pie. In florida its a felony to be an A/C tech without a contractors license and provide repair or installation work as a moonlighting job. Punishment threat of 7 years max jail time plus up to $100k fine. Also the local HVAC parts distributors feel the heat if they sell to unlicensed DIYer. It used to be much different years back. Imagine if automotive parts distributors only sold to licensed techs...people would be broke cars parked. We live in free society? Think again...america is built on its love of money...

[@wholeNwon]

@@hokehinson5987 It's really a crooked state that shelters fraudsters and the people keep re-electing the scum that bleed them. Vote for criminals and you get them. You couldn't pay me enough to live in Fla.

[@somethingkindawonderful3034]

​@hokehinson5987 HVAC people . I have a 2900 sq foot new home .. my hvac guy wants t0vpitvin a 2 ton ac . Says uprising will cause moisture .. Is this true or is he just trying to save a buck on the unit

[@Harry1s]

@@somethingkindawonderful3034 Depending on the age of the house and the condition of the windows, insulation, etc you will need around 6 tons of cooling. A 2-ton unit will do not cool your house below 76 degs and run almost all day long when the outside temps are above 80 degs. They obviously do not know what they are doing.

[@tomwilson2112]

As a former AC tech myself, I really like carrier. Things like dual pole contactors, better sheet metal, and better motors and fans really make a difference.

[@jameseverly8501]

thanks for the information I had a carrier unit at my home had it for about 15 years it was a very good unit very little maintenance a few service calls but nothing out of the ordinary so I thought it was time to replace it it was still working just fine other than old so I decide to replace it got a home improve loan approved and replace the carrier with a Lennox oh boy a terrible mistake I will not by buy another Lennox product again I will go back to carrier or perhaps Trane no Lennox I have had the company who installed the unit come out and work 3 times nothing happened there for no more Lennox going back to carrier but anyway thanks for the comment

[@wawolff6085]

@@jameseverly8501 My two Carrier units are awesome; SEER 19, 3T and 4T running 24/7 here in AZ. Passed 15 years in service.

[@rogerwalk4420]

Put three Goodmans in a 750,000 house 13 years ago. Free parts and labor for 10 years and just lucky…they were offering lifetime compressor warranty at the time. I few things here or there…but generally pleased.

[@LakeNipissing]

Interesting to still see KeepRite within the Carrier family. We have a 1981 installed KeepRite which was built in Burlington, Ontario (the low, green rectangular condenser). In 40 years it has never needed service, and just keeps coming back from hibernation at full strength every summer. There is even an oil heater for the compressor. I actually uploaded a video of this thing a few years ago, and how amazingly quiet it is. My neighbors have a new Carrier which works well, but it starts with 'clank' and a loud roar and hum. The 40 year old KeepRite in our house is so quiet, you have to visually see the condenser fan is turning, to know it is running. The thing is a (quiet) tank!

[@lcee6592]

Funny that reminds me of a 20 cf chest freezer we had. It is a 1954 Wizard Custom 20. We bought the home with the freezer in the basement 1988. We sold the home with freezer in the basement 2016, still running/ keeping temp at -10 degrees. Sadly it was simply way too big and heavy to extract out of the basement. It was quiet and didn’t run very often. Just as efficient as any new one! I’m guessing it had the evil R-12 refrigerant… I wish we had it again!

[@LakeNipissing]

@@lcee6592 Of course it had the "evil" R12, that's why it kept working for 60 years!

[@wholeNwon]

@@LakeNipissing 47 yrs. with my R12 units and still working when I had to replace them.

[@Freezier134a]

Carrier bought keeprite icp in 2011 I think it was, that’s when they went to crap, I quit selling them a few years later.

[@_AmTeC_]

I've got one of these, built in 1982, it's never needed any repairs until now, I love how quiet it is and how tough its been, unfortunately we had some concrete laid around it by some fucking hacks and they damaged the refrigerant lines, and it's lost its charge of R22. This is sadly going to be it's last summer. What a shame, they don't build them like they used to!!

[@timothy5977]

Great video. I've been installing ac systems for over 20 years. There's really no such thing as brand anymore. Cheap coils, fans, contactors, capacitors, and compressers. Seems to me most don't last past 5 years or so now. I pull 25 year old systems out and replace the condenser within 10 years, sometimes less. And I don't know if it's because of the lockdown and they don't have the same people working. But I've replaced more TX v's and compressors in the last 2 years, then I've ever done in my hole career

[@balokurd17]

Same about comercial ref. The copper thinner and I don't think it's price will come down because of the demand of EV industry

[@hvacmike1175]

This usually is caused by poor installation practices. TXV’s rarely fail but are destroyed by failing to follow manufacturer specifications for soldering. We as service or installation techs decide the life of a TXV 99.9% are destroyed in the field when torches are turned on and nitrogen is left off

[@timothy5977]

@hvacmike1175 ok but I've been doing this since 1999 and never had the problems not just with equipment but people not wanting to pay there bills. And now we are fighting online prices with people. People think we work for Carrier, Rheem, etc and we don't.

[@hvacmike1175]

@@timothy5977 I agree we are still having issues with parts on back order as well as finding experienced technicians. I started in this Trade in 1979 putting central air into homes that had never had a/c before using metal pipe and wrap. Also rode with the owner on service calls. Rarely saw a heat pump system. But if you had a leaking evap coil you could usually fix it with a torch and solder. Unlike today’s paper thin coils you have to replace which drives up the cost. We are averaging 20 change outs per week with Trane equipment. We are in the process of moving to Lennox equipment by the end of this year. I believe I will see the end standard equipment in my working lifetime and see variable speed take over the market. I have 5 years till retirement from HVAC.

[@Tony-nx2cj]

We bought a new house back in 1998 and it came with a basic Lenox furnace. It did not come with with A/C but we paid extra for wiring and a fuse box when our home was being built so we could add A/C later. We chose a Carrier brand A/C and used the same company that builder used and worked great. We eventually had to our Lenox furnace replaced but the company was not installing any Lenox equipment anymore so we chose a Bryant heater and A/C instead. No issues after almost 5 years of use.

[@dankelley9361]

Great review of these 5 companies! It’s good to hear from an experienced HVAC tech and get his considered opinion.

[@mikesmith8445]

My Bryant system died after 13 years and I replaced it with a Daikin Fit and have 12 years parts and service warranty. The system is awesome and QUIET and keeps everything nice in summer & winter here in Florida. It was well worth the money and I even got a tax credit and rebate for 3,100. ! Happy with Daikin.

[@dmytrobrovkin8642]

I’ve purchased a house with 5 years old Lennox heat pump. It never worked well and broke after 1 year. I repaired it once, and it broke again next year. Now I’m replacing it with Carrier. Thanks a lot for this video, It helper a lot to pick the right brand and contractors.

[@thebaldmonk621]

When you look at the Scroll Compressor manufacturers (The part that does the work), there are really only 2. No matter who you buy from the only part that really matters is only made by 2 companies.

[@nostradamus7648]

Which 2 companies?

[@Bill.Pearson]

@@nostradamus7648 The one in my Goodman was made by Tecumseh.

[@nostradamus7648]

@Bill Pearson My AC guy just installed an old school Trane heat pump compressor (2007 model XR13, using the old freon). He even threw in a free Fan motor ($600 value) and a new booster and electronic switch because it took much longer to finish than anticipated. Did the entire replacement for $2865 after his military discount. I think I got a great deal.

[@jasonflinders-1984]

​@@nostradamus7648yes, great deal indeed 😂

[@velvetjones1856]

I switched from Rheem to Train as well as switching my HVAC contractor. After having 2 Rheem units that had a lot of service calls, I knew I wanted a Trane because I felt they were a leader in technology. My original contractor said he could get one but it was a "contractor" grade. His level of service was getting worse over the years. I switched to a Trane contractor and bought one of their most advanced 19 SEER units with variable speed on blower and on the compressor. Local gas and electricity companies both sent out reps to see the unit's commissioning and also supplied me with $2500 in rebates. The contractor was very well trained and did a great install, commissioning, and has supplied good follow up maintenance. If you don't have an HVAC contractor that invests in training his people, you will be in trouble because of the current level of electronics.

[@mikewest712]

Seer rating is complete bill when you read the fine print. Most HVAC companies never install these units with the properly matched air handler to achieve the advertised seer rating. I feel for that crap with my trane units. Never again.

[@mr.boniato6402]

My 1998 house has the original 3 ton Goodman and it still running like a champ. Thanks for the info as I am sure mine could kick the bucket any day now, or not 😎

[@deanaltman6841]

I just had a Daiken system installed. A bit pricey but so far it’s super quiet and the heat pump works very well. Much better than my old system. Because I live in your area I’m surprised you don’t see more Daiken’s. They are made in Houston.

[@techbass9440]

I'm almost 100% convinced he's a comfort advisor who sells carrier products.

[@deanaltman6841]

@@techbass9440 Your probably right.

[@DemureDave]

I never heard of Daikin until I bought my home. One of the best, most highly rated contractors in my area sells them and, although I was kinda nervous about it, I decided to trust them. I've been really happy with my Daikin HVAC. You're right, it is really quiet, and it has performed very well in our hot and very humid climate.

[@toddrhine7648]

@@DemureDave And how long have you owned your Daikin unit?

[@DemureDave]

@@toddrhine7648 It has been over 2 years now.

[@williamhager4024]

Over 30+ years in the HVAC business in Florida and the last 10 years becoming the leader in IAQ medical grade filtration. The brand does play a role, but a solid installation will make any unit work properly and have no issues.

[@BushyIV]

Where about in Florida is your service area?

[@williamhager4024]

@BushyIV I'm based out of the north Tampa Bay area, but work the entire state of FL. We just got back from Miami on Friday and are off to Vero Beach on Tuesday. I've been very lucky to be able to stay very busy and overbooked when most companies down here are very slow in the cooler months. Thanks for reaching out, man.

[@BushyIV]

@@williamhager4024 well if you can use one more client, I'm in Palm Harbor and will be replacing my old Trane system. Talked to three contractors so far and didn't get a warm and fuzzy from any of them. See if you can fit me in!

[@williamhager4024]

@@BushyIV DM me to see if I can't help you out. I'm only 30 min from you.

[@BushyIV]

@@williamhager4024 Have to admit I don't know how to do it. I subscribed to your channel on youtube but that didn't seem to be the way.

[@jeffreylindley845]

My AC guy is going to install a 3ton 17 seer Ducane in a few weeks. I have 3 units and he had replaced my other two units with a Trane and Goodman. Both of which are still working fine.

[@jakerazmataz852]

I used to work in the fire safety field. One of our clients was Trane in Trenton. What an amazing factory. Pieces move along on hooks, not conveyor belts, to each station. It was pretty impressive and huge. Well, not at big as an Amazon warehouse.

[@cengeb]

Across from Hamilton Train station, hmmm Ironic? Trane joined up with Mitsubishi Mitsubishi is king of mini split systems, all types, all ratings

[@tonyharrison2542]

I've been in my home on the East Coast (USA) for 36 years. It's a custom home and a mid-level Carrier heating/AC system was installed. It constantly broke down and was in need of repair. Eventually, it was replaced with the top of the line Carrier unit. Same story, it was unreliable, constantly needing repairs and frustrating. Eight years ago, I had a top of the line Lennox model installed. It came with a 12 year warranty. To date (after 8 years), not a single breakdown and has performed flawlessly. I couldn't be more pleased. The only thing I have down to the unit is routine cleaning and maintenance twice a year. When this unit runs its' course another Lennox unit will replace it, period. Two of my brothers and one of my son's have also purchased Lennox units (at my recommendation) and have experienced the same perfect and reliable results, as well as several of my neighbors.

[@briand2614]

Same here, I would never purchase another Carrier. I don't get it. My Lennox has been stellar.

[@kellymccreary3259]

I've been doing HVAC for 28 years. We in the business call Lennox leaky Lennox. Thier gas furnaces will last 30 years but thier evaporator coils will leak in 3 years. Goodluck getting a warranty coil 6 months minimum wait time.

[@tonyharrison2542]

I'm no HVAC expert as you, merely a consumer. I can only report my own personal experience with the Lennox product. To date, after 8 years, zero leaks, zero breakdowns and absolutely 100% trouble free. I'll keep my fingers crossed that this continues...

[@micksmith7140]

Same here, installed a mid level Carrier in 2010 with a twice a yr service plan and it has been nothing but constant trouble. Would never purchase Carrier again! Total Trash!!!

[@micksmith7140]

Mother in law installed a high end Carrier system with twice a year service contract in 2019. Again nothing but trouble. One part to get up and running took 1-1/2 weeks! You couldn't pay me to use Carrier again!

[@PAPATexas]

I'm in McKinney, bought a Trane for 17K a few years ago. I use Baker Brothers. I have had no problems with either.

[@bobbear4437]

We've stuck with Trane, especially with their upgraded Hyperion air handler! As others have mentioned a lot has to do with the installer, which we found a really good one with our Trane system!

[@chucke756]

I agree got 25 years out of last Trane and got another one last year. Goodman is pushed by a lot of big companies and they price them like a premium brand. According to Consumer Reports Goodman is low on the reliability list.

[@snowdogthewolf]

I can't speak for other brands, but I know from first-hand experience that Trane can be neglected (no annual servicing) for years and still "run like new".

[@lancelemay6971]

Rheem / Ruud for me. Rheem furnace in our old house worked perfectly with no issues for 18 years. The Rheem furnace in our new house had a minor flame detection issue after about 20 years ($10 part I replaced myself) - still going strong without any other issues after 24 years. Our Rheem central air unit has had no issues so far (24 years).

[@Ace707xtc]

No issues except for bad efficiency.

[@lancelemay6971]

@@Ace707xtc I’ll concede that point. Predictable reliability and long life is more important to me.

[@ronbaker8007]

In 2012 I had an Armstrong (Lennox) installed; now the nearest contractor is about 150 away. However, it has run trouble-free; 16 SEER 4SCU16LT. Keeping the outside coil clean and rinsed and I change the 4" Merv 13 filter 2x a year.

[@Chainsaw600]

I installed Trane, Carrier and Rheem products in the North Texas area for many years. I eventually landed with my favorite being Rheem. I had several Rheem Classic systems that went 20+ years with next to zero issues. The Trane and Carrier systems didn’t go the distance and were much more expensive for the homeowner. As many have stated, proper installation and design matters. Go with a good, local company and get a few estimates. Referrals from friend is always a good idea as well.

[@edelinois]

Rheem/Ruud the best all around A/C units...I am very loyal to that brand, they've never failed me.

[@bigjohnson7415]

I live in DFW, my house was built in 1999, had a Goodman installed, heat pump. It blew up spectacularly the day before Christmas in 2013. Had ESP air come out the day after Christmas and replaced the inside and outside units with a Carrier. Been bulletproof since, very efficient. Totally happy so far.

[@jonesbc1412]

I have a Carrier gas furnace I installed 3 years ago and has been excellent. I upgraded the AC unit this pre-summer and was planning to purchase a Carrier to keep them the same. After studying different models along with price I then purchased a Goodman. So far this summer the Goodman has run great but time will tell. Both the Carrier and the Goodman AC units use the same Copland scroll compressor. The Goodman was less expensive and has the filter dryer built-in. Carrier has the filter dryer separate which l did not like since more leak potential. My previous AC unit was a Carrier and to me the Goodman looks to have a better and simpler design. (I took the exam to get the refrigerant license).

[@Smedleydog1]

In the area that I live in you see a lot of Rheem, Lennox, Bryant and Carrier, plus a few off brands you didn't mention. We put in a new Bryant HVAC in our house about 6 years ago and it has worked flawlessly. Bryant used to be made in Indianapolis Indiana, but I believe that Bryant and Carrier are now made in Mexico. It replaced a Rheem system that was about 30 years old.

[@BryanTorok]

In 2016 Carrier planned to move all of its manufacturing to Mexico. In January of 2017, after winning the election but before taking office, Trump met and negotiated with Carrier in Indianapolis, Indiana. He managed to save about 2/3 of the jobs slated to be moved. Most of the jobs not saved were being phased out due to automation and would have been gone anyway. There have been further job losses, some due to the market and the pandemic. But, Carrier still has about 800 employees at that location.

[@kenreiner259]

Since your old system of 30 yrs was Rheem, what made you go with a new Bryant system? Curious as I am trying to decide between Bryant, Ruud(Rheem), and Goodman.

[@douglaswatters7303]

I bought about 30 Haier units back when federal standards were about to change and I didn't want to pay a lot for new units. Just 10 seer r22 units. What I couldn't believe after installing was the condenser fan motors were failing after about one year. The first couple i thought was just a fluke, but petty much all of them quit after one year of use. They were just psc motors. Something was wrong at that factory.

[@donaldgeorge6656]

We have a Trane furnace and replaced the AC with an Lennox. Both units perform very well. Again, it all depends on how they are installed

[@bruceanderson9461]

I have always used Heil because of the installer. His work is a work of art! He offers good service also. Never compacted costs with others as installation and service are everything to me.

[@keithglynn9237]

Just a few points...in the Northeast, Carrier can be very difficult to get parts for sometimes, and many times the new replacement part needs to be retrofitted. Carrier also has a tendency to mark up the prices of their replacement parts considerably, not just a little. In the northeast, Trane still rules as far as quick parts access and overall build quality. Carrier would be better if they didn't play games with their customer support and parts line. In the commercial sector, one brand that is emerging, but stands out for constant issues are these "AAON" systems. We are scratching our head with these because they have good brand name components inside but have constant problems with leaks in their alluminum microchannel coils, constant control board issues, heating section inducer fan failures (and these little motors have hall effect sensors, so you must purchase from AAON) temperature sensor failures, hot gas valve seats erroding away, etc. These are expensive units and are mainly a standalone rooftop package. The ones we deal with seem to have an excellent installation ( proper duct sizing, wire sizing, plenty of service area around the units, proper pitch angles for drains, very neat piping and wiring with most everything labeled...whoever did some of these installs did a nice job. ( I know that's rare to hear) So, in this case, I would not blame the installer. We found an extremely wide pressure differential for the condenser fan cycling switches that is non adjustable. We know from past experiences that an excessively wide pressure range causes leaks in coils...AAON did not seem to be interested.

[@TeamWagy]

Your take is interesting, in the south getting carrier parts same day is easy but we have to fight tooth and nail to get trane parts!

[@DemureDave]

One of the largest contractors in my area, Griffin Service, push for Daikin. I have to say Daikin has been an excellent HVAC. It's very smart, and performs very well. I have a rather large home with vaulted ceilings, living in a place where humidity is tough on HVAC systems, making them work very hard year-round. Yeah, the performance is great considering the conditions it needs to perform in.

[@picklerix6162]

My neighbor just bought a new Daikin A/C. I get the impression that Daikin is trying to eventually replace the Goodman name.

[@blueflame0003]

Wow great video...i have a brand new lennox install in August 2019...so far its working flawless but maybe its because its still new ...now before i install the Lennox i did research on all a/c system...and learn its pretty much self preference, you may like one and someone else says its garbage and these are videos from people out in the field. It was either that or goodman...going around ask people were saying Lennox is better than Goodman, and i wanted carrier,went with american standard and now lennox...next i may go to rudd...its now becoming a liftime choice...but if i had it mayway i probably go with carrier...it was here when i bought the house and went bad after 12yrs since....greatly appreciated the videos

[@daveb2280]

Great info! I have Carrier and they are superior. Having access to replacement parts and units is all I need to know in this age of "backlogs" and "supply chain issues."

[@weidles]

If you install a good unit, parts and repairs should not be a concern.

[@mss3834]

They all use the same parts ….there might be a couple small parts unique to your unit but 99% are identical to every other brand.

[@philliphall5198]

I agree on parts

[@dfast8712]

One thing I would like to add about multiple brand names being sold under a few manufacturers the biggest reason why they do this is so they can have more ““exclusive distributors and dealers they make more money that way it’s just the way it works

[@TheHouseofChameleons]

Sisters 8 year old Goodman condenser already leaking. They need to replace the whole condenser. My 40 year Carrier still running strong. ACiq brand looks like a Carrier.

[@WildwoodSubRailfan]

When I bought my house it in 2007 (central Florida) it still had the original Carrier AC (although it had a small refrigerant leak) still running. I replaced it in 2007 with a Trane XL16i heatpump, which has worked up until today with no problems at all. I consider them both to be excellent equipment and agree with your assessment.

[@airtech9629]

Carrier is not even compatible to Trane. Trane is much better

[@mjpottertx]

Goodman was actually a A/C components manufacturer here in Houston. My previous system (which I think was a Bryant) had a Goodman evaporator. The new one is a Daiken built at the old Goodman plant. Daiken has the bulk of the business here.

[@EarlHayward]

Actually, the coils were probably made by AllStyle if they were aluminum… They are in Texas and OEM for a lot of the other manufacturers…

[@dennisblair3186]

Our main house has a Carrier and our guest house has a Goodman. So glad you said this about those brands. We live in Burnet Texas.

[@italukr]

A critical point that the video missed is that you absolutely need to make sure that your servicing company is recommended by the equipment manufacturer. We learned the hard and expensive way. Fortunately we were eventually informed by our mismatched service rep that his company had little experience with our brand and really didn’t understand many of its features. After we changed and brought in a recommended service provider, it cost us $4,500 to correct the deficiencies in our two Lennox units. One major problem was that the prior service company had installed the ultraviolet lights too close to the filters and melted them so that particles were being blown into the system.

[@davidhopper4433]

I purchased a spec home in 1996 with two Goodman units. Both lasted 16 years. Both wore out within 1 week of each other. They were both budget friendly’s . These units kept us cool and warm so no complaints. We are on my 4th home now and we installed Trane’s. These are very efficient and no issues after 3 years. It is 6 degrees F outside this morning and it is very warm inside 😊 72 F & happy !

[@jie1379]

Old goodman build quality is really good. But newer one just not as good as use to be unless you pay for 16 or 18 seers

[@vincentseidle954]

We have a basic goodman unit. 6 years in, no issues. Its also only $1000 for the unit outside so it won't break the bank if needed to replace. Also has a 10 year waranty

[@imaguygolfn]

If you are a diy guy, inspecting the furnace is a vey good idea. As time goes by, small water leaks, smells and coaglated dust can lead to early demise. If not danger.

[@Magnum44NC]

I have an Ameristar 3 ton system, no complaints. Super cooling for south west Florida! Its 3 yrs old.

[@Rick-se5qm]

Our two Goodman heat pumps did not last as long as expected. One required a new expansion valve at the 5year mark and then it developed a leak in the outdoor coil at seven years. Too expensive to repair so the unit was replaced. The second developed a leak in the indoor coil at the 10 year mark. Same story, too expensive to fix so it was replaced with a Rheem system.

[@AdamC5013]

Same here, about to toss it at the 10 year mark

[@akidwaimd]

When I built my home in 2000 I had 2 Goodman units installed. In 2014 my upstairs unit died and the HVAC repair company I had at the time recommended to install a Lennox. In 2017 my downstairs unit died and had to replace it. I had a different HVAC repair company at this point and they recommended Trane or Goodman. I got a new Goodman unit. Fastforward to Aug 29, 2022 and my Lennox (upstairs) unit stopped working. On Aug 31, 22 I was told it needed to replace the condensing coil unit. This coil was on backorder and I had to wait for the warrantee part to come in and be replaced. My involvement with Lennox customer service was terrible!!! They seem to not care about my situation and kept saying that they had no idea when the part would become availble. I was told it could be SIX MONTHS BEFORE I MAY GET THAT PART!!! Some nights it was 82 degrees in my masterbedroom here in South Carolina without the HVAC unit working while waiting for the warrantee part to arrive. Just after my Lennox unit failed I learned that my particular Lennox model was involved with a class action lawsuit!!! During the time waiting for the replacement part, I joked with my colleges at work and friends that I will never buy another Lennox product even if they go into making frying pans, I would run away from anything with Lennox on it like my life depended on it !!!!! Well my part finally came in after 8 weeks of waiting and now my Lennox unit is working. With 1.5 yrs left on my 10 yr warrantee, if my unit breaks down tomorrow again, I will not go with anything made by Lennox!!

[@akidwaimd]

I was subscriber #10 and proud to be #10!!! Keep up the good work !!!!!

[@atlasacrepair]

At least in 2017, you went with a Goodman as opposed to another Lennox. Yea, we've heard about their customer service or "lack thereof". It's like they've lost site of who the customer really is. You being told they had no idea when the part would be in or the possibility of being down for six months is so crazy!! Wow, this just adds to the number of horror stories about Lennox we've heard over the years from customers. I hate to say too funny 😂 but awful! Thank you so much for taking the time to talk about your experience Asif and THANKS SO MUCH for being our 10th subscriber 😆🎉

[@elgringoec]

These once diligent brands are now riding their own coattails! I bought a Maytag wall oven, you know, the company who shows the repairman sitting around twiddling his thumbs in the advertisement. Soon into it, the unit goes haywire. Googling for information on the problem, I found a lot of complaints, and a class action lawsuit. But in Canada! I called the company and they told me that I could buy a new control board for it. And they couldn't tell me if the new control board had addressed the problems which plagued these units. I have to swear off that once reputable brand.

[@bobboscarato1313]

I sold a few Lennox units 30 years ago; then I switched as a dealer to American Standard and Trane and my customers were a lot happier.-

[@elgringoec]

@@bobboscarato1313 But that Lennox guy wears the coolest hat!

[@dadlovestofish]

I have a Tempstar which was installed in 2004 and still going strong. I'm religious about changing the air filters every 2-3 months depending on summer or winter. I live in central Florida and the heat is crazy in the summer, therefore, more frequent air filter changes. Great advice as I'm soon going to be having to replace my unit. I'm happy with the longevity of the Tempstar, but I'm realistic as well. Can't expect these things to last forever. Thanks for the review

[@corgiowner436]

I’ve had Lennox’s top of the line systems for about 5 years. No issues. Only annual check ups. Super quiet and they have an infinitely variable compressor output. Very efficient.

[@twolfe4295]

I have installed and/or serviced almost all of these brands over the past 40 years. I recently began installing Bosch heat pumps. They are inverter units. In my house I installed a Daikin Skyair inverter ducted system several years ago and it works very nicely. One thing that seems to be important is the actual availability of tech support, parts, and warranty.

[@gradywhite9781]

Thinking about installing a Bosch hybrid system. Any thoughts on their products since you've been installing them?

[@cowboy7271]

Had a Goodman put in 06 still going strong replaced two capacitors and one fan motor it's really good man😂

[@DSC800]

Interesting, and you didn't bad mouth Goodman. I went with a Goodman two years ago. The deciding factor was their willingness to sell direct to the DIY homeowner. I self installed my 3 ton unit, basically a plug and play replacement for a 32 year old Carrier and then had a local tech perform the charge, txv and settings. Quotes from contractors for the job: $9500 - $12000. My cost all in: $3900 (plus about 40 hours of my time). Zero problems so far and so much more efficient.

[@amigo4909]

I have a goodman AC and furnace purchased at separate times for the same reason direct sell to the customer. I paid cash to a licensed contractor to install them. The AC unit installed 2016 the Furnace in 2021 both no issues to this point.

[@diyhvacguy]

Amazing. I love to hear a diy success story 👊🏼

[@saltysteel3996]

After knowing people that worked in the Goodman factory, and the horrible stuff that goes on in that factory, I wouldn't touch one with a 10 foot pole.

[@scotty362100]

@@saltysteel3996 Leaves more for us! Your loss out of sheer stupidity. roflmfao

[@tumbleweed-life]

I’ve had a Goodman unit for about 10 years now did the same thing I ordered it online they shipped it to my door I installed and wired it up but had a AC guy I work with do the hot work and a pre-start check. During the time I’ve had the Goodman equipment I did have to replace one start capacitor and so far that’s been it. I work in a maintenance department for a public school system and we use a lot of train products and train should give their equipment away and just sit back and make their money on their parts!

[@MBihon2000]

I had a Comfortmaker AC and heating systems installed some 25 years ago, still running great. I had 2 occasions when my starter failed. Once my AC had a leak, was fixed easily by a tech for only $120, 2 hour service call.

[@coolmandude1000]

You might want to mention that AMANA HVAC products has tbe absolute Best Warranty available in the HVAC industry. AMANA offers a LIFETIME UNIT REPLACEMENT ( 99 YEARS ) if a compressor ever fails in 16+ SEER AC or Heat Pump units. AMANA also offers a LIFETIME UNIT REPLACEMENT for some 80% AFUE Gas furnaces & 95% + AFUE Gas Furnaces. AMANA also uses STAINLESS STEEL Heat Exchangers in those Gas furnaces with LIFETIME UNIT REPLACEMENT WARRANTY. CARRRIER / ICP Products are now using Microchannel Evaporator coils V Coils and we all know about the YORK Microchannel coil failures. Only time will tell if Carrier/ ICP made a good decision going to the Microchannel design. I just found your KZbin channel and just subscribed. Keep up the Great Work. Cheers from Baltimore Maryland !!

[@timfife2128]

American Standard has been rated number one , for around 14 out of 16 years, with Trane being 2 nd

[@dtouw]

Amana is garbage

[@justinpennington7682]

@@timfife2128 rated number one in what ? Paying for advertisements? It sure as hell isn't quality

[@69A12SuperBee]

Amana=Goodman

[@DocNo27]

I just got a new house with the Brian air conditioner and was not happy to see that it had a micro channel condenser. We will see how it lasts.

[@craigroesberry3316]

It's crazy how people have different experiences with these different brands.

[@Postumeartist]

I think some of that may have to do with who installs what in your area. Rheem and Ruud are top tier where I am with virtually no failures ever. Goodman is absolutely awful. Probably the worst. We’ve changed plenty at year 7 from dead compressors and unregistered warranties. But here’s the thing: the cheapest brand in your local area will attract the worst contractors. The bad fly-by-nights won’t install anything higher end, because they sell only on price. So whatever’s cheapest in your area will probably attract the worst contractors. In my experience with acs, it’s 90% the install, 10% the equipment. Although I can’t prove it, I’m pretty sure all those dead compressors on 7 year old Goodman’s was more due to poor installation finally killing it. If you buy high end or mid range, you’re more likely to avoid bad installers.

[@jiggidyjam]

I’m a builder and have installed Goodman for over 20 plus years and it’s served me well

[@carlstypinski1517]

What can you do when you have a manufactured home, and Goodman is the only down draft system around? I bought a Goodman system last year, the most efficient that would fit into the existing space and so far its working well, both furnace and a.c.

[@DocNo27]

There’s nothing wrong with Goodman. I had two Goodman units over 20 years old that ran fine before I sold my house. Most air conditioning systems problems are due to poor installation not the brand as they almost all use the same parts, same Copeland compressors, same manufactures for the controls - that’s the real dirty little secret of the industry.

[@cardsfan-ym1bj]

Nothing wrong with a goodman,they get a bad rap cus they sell to anyone,all these brands are only as good as the installer,not sure who told you goodman is the only one that sells a down flow unit,almost all air handlers and furnaces or multi positional these days with some slight modifications