Suburban Crank No Start. 3 Day Fix.

smh. nbd. lol.

[@thewisecracker-rq1pu]

Crazy story for anyone having this similar problem and this video didn't solve the problem. I had a 96 GMC Yukon with 5.7 vortec that all of a sudden would not start, it cranked, but no start. I did the exact same thing as this video, and more, and nothing worked. After 3 days of hitting my head against the wall I had my wife crank it over while I did some more tinkering. I then noticed, by looking at the fan blades, it was turning the wrong direction!!! I was like WTF??? I then replaced the starter and VIOLA! It started right up because it was now turning the proper direction! Unreal! That was the first and last time I have ever seen a starter all of a sudden decide to start turning the wrong direction. Maybe this will help someone else someday. Cheers!

[@garygarner482]

92 Corvette,40,000 miles,just bought it, no start, no fuel pressure at the rails, new fuel pump and new fuel pump relay i hope. Aaaarrrrrrrhhhhh.

[@joemanifesto8742]

Damn that was entertaining! Good job on the video and presentation.

[@EvanNolen1989]

Thanks! Glad you enjoyed it

[@whitemike7822]

Ive been throwing money at a newly built motor. One thing i have not done is clean the cap. Gonna try it tomorrow and ill come back if it works to say your freaking awesome. Wish i didnt replace the fuel pump today cuz it didnt make ot start

[@EvanNolen1989]

Checking spark(ignition) is crucial. I assumed mine was okay because I could see spark when I pulled the plug. But what I didn’t take into consideration was the QUALITY of the spark. That’s when I popped the cap and found the corrosion. Simple fix. Hope that’ll help you out!

[@wannaPreG]

Nice one buddy, wish I can join your team and work together

[@agapitogarza1112]

what about on a 1950 chevy will it affect it as well ! i have crank but no start!!

[@EvanNolen1989]

You need fuel, air, and spark/ignition. Make sure you have all three

[@jakedog20]

Awesome video. Did you have to perform the crank shaft position sensor relearn after you replaced the sensor? I’ve got mixed answers about doing a relearn for this model of truck.

[@EvanNolen1989]

Thanks man, I just swapped it out

[@dyllanman9474]

Hello sir, great vid. I got a 2005 ford expedition same issue. I have fuel to the rail and I have spark aswell as compression. Any idea what my solution could be? Thanks!

[@EvanNolen1989]

Thanks man! Make sure the fuel pressure is in range, like 30-40 psi at idle. Make sure your spark is good; part of my issue was weak spark due to corrosion under the cap. Hope that helps!

[@lilvedo1]

That loose part is map sensor they don't fit real snug anyways there is just a rubber o rings on them

[@EvanNolen1989]

I pulled it out and checked the o-ring, jammed it back in

[@scratchalotrecords3172]

Good Video thanks

[@EvanNolen1989]

Thank you!

[@Luiscruz-hg7nv]

Similar problem for my 96 gmc but when I check for fuel pressure I get nothing/zip/nada

[@EvanNolen1989]

I’d check the fuse first then check the relay. There should be a relay next to it you can swap in or you can jump the terminals with a short wire. If the fuse and relay are both good then you can confirm you have voltage at the plug above the rear axle, if you do, you have a bad pump.

[@voguetyreturner]

What codes were you getting if any?

[@EvanNolen1989]

There were a few codes, I think one was an O2 sensor. I ignored that because I deleted my cats

[@isrraelgonzalez2185]

Fuel pump

[@josegalvan775]

Mine was showing a code and recommended fuel injection cleaner

[@Blackford86]

Go rent a scan tool

[@EvanNolen1989]

Got one