I'm seconds away from using a stick of fucking dynamite.
@NR-os2cwАй бұрын
🤣🤣
@staceymc197221 күн бұрын
same
@sillyhandy Жыл бұрын
Great! I'm lucky to find this way to take out the plate. I used ratchet but not pry bar. Other videos just remove it so easily and I look myself stupid. lol
@ButtersCCookie9 ай бұрын
Best video on here! WORKED! Fast and informational. Husband wouldn't wait to soak it. Took him an hour to untangle the ratchet strap. Used some pencils in a rubber band. Walmart is 3 minute drive.Yall made my day!
@sterlingreed13639 ай бұрын
Glad it helped!
@choowaikong8578 Жыл бұрын
LG should do a better design so that it can be dismantled easily
@Jimmydholt Жыл бұрын
Great idea with the strap. Worked for me without ratcheting. Thanks!
@brianwherry72552 ай бұрын
Wonder if a longer bolt of the same thread would press it up?
@moagoo5714 Жыл бұрын
I tried several methods, but this is the one that worked. God bless you for sharing this!
@grundyb Жыл бұрын
Great idea! I only soaked it with WD40 and it came loose after soaking for several hours. I was almost lost on how to get it off but got lucky with that WD40.
@ButtersCCookie9 ай бұрын
I would of just fill it up and leave vinegar or use CLR for a couple of hours?
@michaelhartman75942 жыл бұрын
Great idea, I’m going to try this
@tompatzkowsky568724 күн бұрын
I attempted this. I’m pretty strong and could not lift the plate off with the strap underneath. I am mechanically inclined, I was frustrated and called it a day. The next morning, my wife put vinegar and boiling water on it. The plate just lifted up. It hadn’t been cleaned since we bought it 8-9 years ago. Needless to say, work smarter, not harder.
@CesarEstrada9223 күн бұрын
Can i run a tub wash without that tub plate?
@laundryandtrainman24672 жыл бұрын
What kind of model is it?
@nickmorrow7229 Жыл бұрын
I would have thought a mechanical puller would do the job. The pullers are used to pull a steering wheel off the spline shaft or pull the thrust bearing from input shaft! I wonder if anyone has used this method l have mentioned
@jjwo711 Жыл бұрын
Having the same issue. Where did you use the pry bar? In the middle?
@sterlingreed1363 Жыл бұрын
Yes the pry bar was placed over the top center.
@akmv1 Жыл бұрын
Got a wire hanger and hooked it into two of the three holes and pulled as hard as I could, feels like it didn't move an inch. Might have to do this, I'm losing patience
@johnmichaellunstrumsr.77162 жыл бұрын
having the same problem right now. heading to get a ratchet strap 🤦♂️
@RyanOlsen Жыл бұрын
I had a coin stuck in there that I was able to get out with pliers. When that got stuck, do you think it could have caused permanent damage?
@sterlingreed1363 Жыл бұрын
Besides scratching the wash plate. I don’t think the coin would damage anything important.
@RyanOlsen Жыл бұрын
@@sterlingreed1363 Thank you so much for your fast reply. I ran a load with just a couple of towels and could see the wash plate agitating the clothes, so I think I'm good. I couldn't see that happening with a full load.
@BOB88o2 жыл бұрын
great post
@Mostballestplaya2 ай бұрын
I couldn't get the straps inside that small wedge even with a putty knife 😑
@brianwherry72552 ай бұрын
Omg I hope this works. At wits end over here .
@nicolekelly85028 ай бұрын
DON'T DO THIS! TRY MY METHOD INSTEAD!! I watched a TON of these videos and only 1 worked. I felt dumb after trying all the tools and straps. Just take off the plastic cap. Remove the bolt. Pour in some bleach and set it on 'Tub Clean'. I canceled the cycle at 0:50 and the washplate was there floating in the water. Stupid easy. The tub will drain automatically after a while or you can just close the lid and let it complete the cycle. I felt silly after trying to manhandle the washer! (Note: I'm 5'2" petite female and probably wouldn't have been able to muscle that thing off anyways.)
@frosttvy11546 ай бұрын
Tried it didn’t work
@frosttvy11546 ай бұрын
I let it stop at 50 but my washer doesn’t have a cancel cycle
@genamaranto18755 ай бұрын
This worked like a charm!
@lucasnickolson34253 ай бұрын
Mine is so stuck it won’t even do that. I tried every single method so far and nothing has worked
@robertalarsen4158Ай бұрын
This idea of using bleach really did work! We tried so many suggestions - I didn’t think bleach would work, so I tried a washing machine cleaner cube thing thinking that it needed the minerals dissolved more than a disinfectant. That didn’t get the plate out but got a lot of gunk. Then my husband told me to try the bleach suggestion. The plate just started floating in the wash cycle with about 27 minutes left (before rinse cycle).
@jacedebois8926 Жыл бұрын
Sick
@rochroche91672 жыл бұрын
LOL! no luck taking it out for me.
@rochroche91672 жыл бұрын
yeeeeeeey about time.. it comes off. i used similar to your idea but used a wood to pull the side rope, then on the middle of the supporting wood I roped ratchet while both side rope are aligned, like a --C shape, then start tightening ratchet rope, finally comes off like no sweat. Could have thought if it yesterday,. :)
@sly9263 Жыл бұрын
I destroyed mine trying to remove it- what a piece of shit design.
@choowaikong8578 Жыл бұрын
LG should do a better design so that it can be dismantled easily without damaging it..Stupid company
@heatherschoening3925 Жыл бұрын
My Samsung washer has this agitator plate thing too. I can't for the life of me get it off. I tried otherhow-too video's, and they say to stick a screw driver in one of the three holes under the cap and just pull up... but when I do that I feel like the screw driver is gonna snap or I'm going to break something. It's difficult and definitely a poor design.
@sly9263 Жыл бұрын
@@heatherschoening3925 I wound up buying a new agitator plate and ripping the old one out with vice grips
@iamthemiracle81 Жыл бұрын
Same. Things a fucking toilet
@warrenwarren43397 ай бұрын
Just run it on cleaning mode
@WolfNRaven6 ай бұрын
I'm doing this now and nothing. That shit is really on there
@sterlingreed13632 жыл бұрын
Lgwt5070cw
@sarajanereid4598 Жыл бұрын
Sorry, I'm 70 years old and short (lady). I haven't the strength.
@sly9263 Жыл бұрын
I'm 6'3 225 and I work out- couldn't remove it. Something is wrong with the machine design- probably why it's discontinued.
@samkitty58942 ай бұрын
Not a good method as all the pressure is on the outside. You'll end up bending the hole thing. But that doesn't matter as you'll have to replace the entire part any way. I have a good removing the bolt and running the machine with water and some bleach. Movement pushes it out.