Super Bee w/ a 3 channel radio, Gas RC Kill Switch, Killer RC

[@osmarcastillero1500]

Osmar Castillero I did every single test And I notice if you or if the coil cable get disconnected from the supper bee kill switch the engine still running. I tape my around to make sure will not comes off

[@MrKillerRC]

Yes. Make sure the ignition wires wires are securely connected to the ignition coil. You can pinch the spades with pliers to make them fit more tightly.

[@brianwallace4842]

What's is up ? You mean towards wire terminals or what

[@acejossy]

Does Super bee kill switch work with Spektrum AVC because my Spektrum AVC interferes with it. When the AVC is on, the kill switch automatically turns the engine off and it doesn't take any input from the transmitter thereafter. So I have to turn off the AVC and then the switch gets turned on or off from the transmitter.

[@rtoebak76]

Very good explanation. Thank you :-)

[@henrygonzalez6421]

I thought you needed a cutoff switch to be able to use the third Channel. please help

[@ezeeboy]

i turn off my transmitter but the killer be doesn't cut off the engine... everything works fine otherwise. help please

[@MrKillerRC]

[e-mail] Probly just need radio settings changed.

[@faniss1380]

I have the same problem. Did you find a solution? Please let me know

[@daddonimrod7846]

hi I'm wanting to run etc Leds off my killer bee so I can see it x from a distance can you point me to a how do please thank you

[@joemilnes9062]

I have a 4 channel receiver but only 2 channel transmitter. Which video should I follow?

[@pb2themax]

Treat the receiver like its a 2 channel receiver. There will be power on channel 3 and 4 but no signal. So you'll need to put a splitter cable on the steering channel for the Super Bee. Flip down the #1 dip switch on the Super Bee to turn off Aux control.

[@joemilnes9062]

Ok thanks. So even if I plugged it into ch 3 or 4 and turned my transmitter off simulating a radio glitch, nothing would happen?

[@pb2themax]

Joe Milnes With a 2 channel transmitter, If you plug the Super Bee into channel 3 or 4 the Super Bee would think there is a constant radio glitch and you'd never be able to start the engine.

[@joemilnes9062]

Oh thanks for the help!

[@craigtreeguy]

Could u do one on the stock losi spectrum receiver I have the dx4s and the new kill switch

[@pb2themax]

For a 3 or 4 channel radio you don't need to change any settings on the Super Bee. Just set the radio like this. www.killerrc.com/forum/viewtopic.php?f=13&t=1077

[@craigtreeguy]

Thanks for the reply

[@Bathurst_1000]

Hi guys Can you please send me the link to the 2 channel kill switch- thanks

[@jurestarc]

what if the receiver stops working ?

[@Schofield131]

How dose it shut down the car?

[@TrouserSnake69]

Where is killer rc i ordered one and its been 2 weeks no response no calls nothing?

[@samchiarelliz24]

Another video and another video and another video

[@rodtaylor62]

It comes on red at first i hit channel 3 it goes green runs for a minute shuts off

[@MrKillerRC]

Roderick Taylor Does this only happen when the engine is running? It could be radio interference from a bad spark plug resistor. Install a new NGK CMR7H spark plug and try it.

[@rodtaylor62]

@@MrKillerRC ok thanks

[@pb2themax]

For installation on a HPI Baja see this www.killerrc.com/forum/viewtopic.php?f=25&t=586 For installation on a Losi 5IVE see this www.killerrc.com/forum/viewtopic.php?f=25&t=565