Super phone holder for bike DIY. Simple bicycle mount for smartphone

Friends, ATTENTION!!! The video is entertaining, shows personal experience and IS NOT A GUIDE TO ACTION! You are responsible for all your actions!
ali.pub/1lk6pq - Universal Bycicle Phone Holder.
Homemade phone holder on the bike DIY at home. Interesting idea bike bracket for the smartphone. How to fix the phone? Bike mount for phone. The device is made of simple materials available to everyone. I called it "Crab" :) any other ideas?
MATERIALS:
1. The neck + cap PET bottle
2. Plastic end cap from the front of the computer
3. Plastic cards
MANUFACTURER:
1. Precisely cut the the neck of the bottle and carefully sanding until the formation of a smooth surface.
2. Unscrew the cap of the anchor and to measure the diameter of the protruding part.
3. In the lid drill a stepped drill hole of the required diameter. If there is no drill, you can use a scalpel. The hole can be made a little less.
4. Insert the cover of the anchor to the inside of the cap from the bottle and tie to the steering column of the Bicycle.
5. Note the "open" position (entrance of the bottle cap). To tighten the neck until it stops. Note the "closed" position, but then still have to move.
6. Take the plastic plug and attach the phone. In my case I had to bite off the clips with one hand.
7. To attach the cap to the neck and to find the optimal position. For me it was important that the plastic is minimally protrude from the steering wheel and I tried to move it as far forward as possible. Mount the rudder to the removal was the endpoint of the holder, at the same time, a second point of support.
8. To mark with a marker the position.
9. Sanding place for bonding and degreased.
10. Apply a second adhesive and strongly pressed parts to each other.
11. To use plastic card and cut into strips of the desired width. For aesthetics I cut out black strips.
12. From the edge of the strips to measure 5mm. Other sizes will totally depend on the size and shape of the phone.
13. Heat and bend the edge at an angle slightly greater than 90 degrees. Further heating the plastic to bend it in the shape of the edge of the smartphone.
14. Attach the smartphone to the holder and measure the retainer. For symmetry I cut off the latch on the middle level. If this is not important, it can be glued not cutting, so it will be safer.
15. Pre-identify the location of the clips so they do not interfere with the controls. Then sanding future gluing, treated with alcohol and glue.
16. Holder is ready! Make sure you work the latch is securely holding the phone. If Yes, then the device is ready to mount on the bike.
DISADVANTAGES:
1. The mount can break from a lot of exercise. For example, if you accidentally hurt a foot or hand.
2. In the fall (sudden strike) phone can be a little out or even pop out of the clips.
3. The holder can Unscrew if hurt or falling.
Cashback Aliexpress, Gearbest, Banggood: cashback.epn.bz/?inviter=4087b
I share all that I am doing own hands at home. The channel you will see homemade, crafts, repair of equipment, experiments, tests, unpacking and review products from China (Aliexpress), various household manual. I also will share my inventions and interesting ideas to improve and simplify the life (life hacking).
Movies shown on that channel, show the personal experience and are entertaining. For all that you do, you answer yourself. Observe caution and safety rules.
///////////////// SUBSCRIBE \\\\\\\\\\\\\\\\\
********* goo.gl/Tp0aX9 **********
////////////////////////////////////////////////
////////////// MY CHANNELS \\\\\\\\\\\\\\\
goo.gl/IlJ8ZE - Dikovinniy World
goo.gl/GLJ2hf - Alexander Dikovinniy
*************** PLAYLISTS ***************
goo.gl/lTXljH - Instuctions
goo.gl/Jy8Xjd - Parcels, Reviews, Tests
goo.gl/RtQfXg - Water Device
goo.gl/u4Snhv - Interesting Ideas
goo.gl/LzpXou - Repairs
goo.gl/lzM9Yg - Toyota Camry Gracia
goo.gl/zOHwUB - The use of plastic PET bottles DIY
**********************************************
MUSIC (KZbin Audio Library) [My channel - Create - Audio Library]:
1 - Deep_Hat
2 - Fun
3 - South_Town
4 - Rustled Feathers
/////////////////= HELP CHANNEL =/////////////////
PayPal: [e-mail]
Webmoney (WMZ-dollars): Z315805724463

[@dial2277]

Friends, ATTENTION!!! The video is entertaining, shows personal experience and IS NOT A GUIDE TO ACTION! You are responsible for all your actions!

[@shadigif8916]

idiot

[@iornstryfe8041]

love your vid man

[@ephtea614]

You have a lot of faith in super glue.My phone would go flying on the first bump I hit. Nice job though.

[@arjunmadhav2847]

Thank you for making this video! Its a pure example of DIY plus making best out of waste😃. My mobile holder was lying unused for so long, as its connecting portion was lost. I used the bottle cap & neck idea to fix it and now I can use it again!!! It looks cool as well. Thank you.

[@sa6kad]

The superglue is very unreliably method! It glues hard but it's pretty fragile, it can break down because of vibrations.

[@ramprakashjayabal2169]

This is real diy.

[@mae1712]

Thanks so much! I dont really wanna go through the process of removing that handlebar cap and all, but i figure you can just use a bike bell mount and hot glue it there.

[@dial2277]

Hello, friends! Do you like to ride a bicycle? :)

[@rajendramahar2272]

Yes

[@rajendramahar2272]

Plzz subscribe my channale

[@joax7732]

Yesssss!!!!!!!!

[@jx592]

Dial Yes, and unlike Freddie Mercury, i DO like Star Wars

[@bertzkan]

Dial yes

[@dial2277]

Friends! What do you want to see in my next videos? What you like? Write your ideas.

[@rajeshnayak9542]

make video about real time GPS tracker..... waiting.....................................................................................................

[@gangadutta83]

Plz show how to make bottle stand for cycles

[@69xesportgaming7]

How to style a cycle

[@farkhanofficial]

bikes ready for the road

[@mohdhelme6180]

That clicking sound so satisfying

[@dial2277]

I like it too))

[@songmingi]

The length people would go to save little bit of money for proper bike mount. Really hope people make something like this for funsies, not for actual use. Phone is actually expensive.

[@KrstaBandito]

Thanks for idea, i just finished my version. This video help me so much. Btw i secure it on old light holder and its very good. ✌

[@dial2277]

Great! I am glad that my video was useful for you. Very nice. That's right, let the old holder work further! Thanks for the comment!

[@Solotraveling1999]

@@dial2277plz suggest which bottle cap i can use for this phone holder

[@LakhwinderSingh-vl2fk]

What material you using in side for hold the mibile

[@Solotraveling1999]

Plz anyone tell meh which bottle cap i can use for the phone holder

[@battlebaymaster5965]

Which glue ur using name pls

[@earljamesbarilea2447]

Saan mu na kuha young cup???

[@atanubhattacharjee9814]

Superb idea... much appreciated....

[@Hyra-hw8ru]

Thats amazing good jub 😍😍😍🥰🥰🤩

[@drumskas]

Genius like me. Haha great job

[@mohamadzulhilmi5953]

great job bro!!! 👍🏼👍🏼👍🏼👍🏼👍🏼

[@saintrajkumar]

Awesome bro.. 👍✌️ wats ur profession btw ?

[@marcogarofalo6343]

This is very good. The only thing I would do is cut a hole in the black plastic, screw the bottle part in some how and then glue it. That way it can never detach, as its trapped between the bottle neck and lid. Also you have access to headset bolt.

[@dial2277]

Thanks for the comment! Very good idea!

[@egyptteam8238]

Thank you

[@hardeepsinghdeepa3833]

Good stand

[@southernexposure123]

That's pretty cool.

[@newboysgeneration6198]

I like it...it looks very strong and rigid....i would try it

[@muhammadnajeeb983]

I tried It's amazing

[@Gantzz321]

general build is ok, with the exception of the arms, I would pre-bend them so that they would be pushed out when the phone is locked in, NOT away an friction held in place, one bump an they could de-clip an bye-bye phone. If they were pushing in (because resting state was narrower then phone) on the sides at all times then this would not happen.

[@cring0101]

really really cool !

[@ylovkush]

Simply amazing ❤️👌

[@Marllb0r0t0]

Thank you. its a very good idea. I olso will make.

[@dial2277]

Thank you for watching and commenting! Be careful, it's just an idea. The adhesive may not hold the plastic parts securely enough. The purchased holder will be better.

[@mahhubbard]

Dude awesome build!

[@anilpillai10]

Very nicely done 👍🏻

[@stephanpetit5199]

It's the best idea of i never seen

[@dial2277]

Thanks bro!

[@mindaugasjakubonis149]

Some metal for background would be better

[@luter82]

Why there is not a clip in the front? It's gonna come off when you brake. Plus superglue is not the best for this. Use epoxy.

[@nikosvl3976]

Very nice idea but fhone base for bikes he have only 3euro

[@SayurAsem21]

kalo kata emak gue, ngapain capek2 kaya gitu, mending beli ada yg harga 20rb

[@karthijeeva776]

Good work ..

[@ownideanewcreation600]

Osm idea

[@colterpan]

I Wonder All this Materials Can buy a new one at the store...

[@ericklopes4046]

Ingenious idea you came up with, great craftsmanship right there. Too bad you damaged your screen on the making ;-( Maybe there is a way of making a template of your phone or just put something thin and soft to protect the screen.

[@dial2277]

I spent a few days developing ideas and experimenting. Even there was an option to use a paper clip, just it damaged the protective glass on the phone screen. The paperclip was a metal without a plastic shell. Now you only need to replace the protective glass. The screen itself is not damaged. The latest version of the holder (the one on the video) is safe for the phone. It is desirable that the phone was in a simple silicone case, and the screen protective glass. If you're still nervous, you said you could put something soft on it. For example, glue pieces of rubber. Thank you! I am glad to your comment! Godspeed! :)

[@rickyvanswaal]

Nice build, altho the lifting by the cellphone was a bit painful to watch :P I might make such a device for holding my phone with navigation in the near future

[@dial2277]

Thanks for the comment! I was afraid of :) I wanted to demonstrate that plastic cards are a good material for a homemade.

[@juraj_redeky]

very nice project! THX

[@dial2277]

thank you very much!

[@adamramdan2557]

thanks for idea!

[@azeri-pakistan-turkiybroth8943]

nice video😎

[@startriker547]

Instead of the computer part, what else can I use?

[@dial2277]

Can be a flat piece of wood (laminate or veneer).

[@startriker547]

Dial Tks 😉

[@sajadmanzoorbhawani]

Best to use your own mobile cover/case instead of computer part

[@earljamesbarilea2447]

Where do you get the cup?

[@dial2277]

Uh, what cup?

[@Blackcannon-fm5bb]

ANIME BAD PLAYER it's a Gatorade bottle top idiot

[@user-pi3fh9cp5m]

Gj on nails. Also I feel one piece bolted to frame would be more secure.No need for screw cap... Impossible to melt both plastics togetger in the oven instead of superglue? I feel like superglue can easily break if the bike falls or goes over a big bump.

[@user-pi3fh9cp5m]

But apparently superglue is magical. Good tests.

[@dial2277]

If there is any doubt in the usual superglue, you can use special plastic. It kinda melts the plastic and better glue. I recently fell off my bike)) Mount in place. The phone is a little out of the seats. I think only a direct impact force on the holder may be damaged. Some of the shortcomings I mentioned in the description. Thank you for your feedback and questions! :)

[@AlbertBester]

Dial, great video, very impressed with detailed and clear progression in all steps of make. Especially pleased to see excellent work practice with the use of CA glue (super glue). It amazes me how little attention others pay to this particular detail, the result of which is, people all over the world are failing to get best performance from their glues.

[@dial2277]

Thanks for the nice words! I'm glad you appreciated my work. I often use this glue at home. The composition of the adhesive: ethylcyanoacrylate.

[@tmayberry7559]

Not true I tried it with the on bike on a city bus also took the bike on gravel roads worked unitil the glue lost it's bond due to contact points

[@spytech9525]

Awesome

[@teetje5]

Nice as idea as well but some bikes don't have that mount on the steering wheel and other video ideas don't require so much work

[@dial2277]

Thanks for the feedback! Maybe I'll figure something else out!

[@ravingagunawardana178]

I like your work

[@dial2277]

Thanks

[@ColinBarling]

That's Cool

[@dial2277]

Thank you very much

[@teogomez4394]

Holy shit you made an odyssey from something that could be really easy. Not even building your own bike is so damn elaborate

[@hardeepsinghdeepa3833]

Nice

[@vcfusion1435]

If you go over a bump it’s gonna come off

[@itx.pagrotraap.editz..5893]

Your phone screen get damaged

[@unstoppable6470]

Cool man

[@ryanshah5078]

Amazing:)

[@marbinsingh7907]

Thanks bro

[@NorthernScrub]

This could be improved by cutting a portion of neoprene (for example, from an old waterproof CD holder) and placing it such that it grips the back of the phone and also offsets the impact of the road.

[@dial2277]

Thank you for the addition!

[@mordziatymordziatymordziat3634]

Nice idea

[@dial2277]

Thanks! :)

[@mrkhoros]

way to make scratches all over your phone bud.

[@marriedvlogger275]

How to get smartphone bike mount for cheap: 1) Walk around bike parking lot and look for phone mounts 2) Steal the one you like

[@denzzz28]

R.I.P. phone.... LOL!!! I wont trust that with my £800 phone

[@mrchedda]

What world do you live in that this is simple? Lol

[@dial2277]

I meant that everything is made from available materials and does not require special tools. Well, I agree, the average level of complexity))

[@user-yn1ur6it4g]

👍😍👍👍

[@amita7555]

Ek bump me na mobile rahega na holder..... Never want to try this

[@suryateja5954]

Better to buy mobile holder from shopping websites

[@jimueldonaire2742]

"Tip" ~YOU CAN ALSO DO THIS ON YOUR CASE

[@reneecase8678]

so satisfying

[@prodbymed_flp]

Nice m'y brother

[@dial2277]

Thanks

[@mbastos1000]

this is not gonna fly! super glue will not keep it in place for a long time. No way I would put my iphone on this thing lol

[@qusayali3546]

🤓👍👍👍👍👍👍

[@jetstreamdefalpha5411]

God dam....just buy one ,there like 10 to 14 bucks

[@TogheFace]

well, its nice and all... but i'm not gonna trust a $900 phone to creditcard pieces :)

[@dial2277]

I understand you))

[@bobbymac1319]

Or you just go and buy one

[@Odykost]

Or just go buy one

[@jetstreamdefalpha5411]

I can picture a stupid kid tryin to do this and ends up burning his house down

[@liverpoolforever6070]

If u r cycling in a rainy day!!!! Your phone will die!!!!

[@joax7732]

Why would you in rainy day

[@joax7732]

Ar u thinking???

[@Isagiyoichi7K]

Are you just encouraging people to use phones while driving?

[@dial2277]

Do you use the Navigator in the car? It's the same :)

[@deadchannel4708]

Dial a car is way safer than a 2 wheller

[@joax7732]

DarkoMon hhahah 2 wheller😂😂😂

[@Isagiyoichi7K]

Joachim Amoroso stop this bro, dat was just a mistake, and like c'mon now who doesn't know the spelling of wheeler, it's just a mistake while typing so stop abusing him

[@Husk-E23]

PLANET MINECRAFT have you ever heard of a bike computer? To keep track of time spent, location, and distance riden?

[@lukasbaumgartner4303]

Scrap 😂😂😂😂😂

[@Valeria-qb8if]

Easy? Pffff

[@andriusdaraskevicius]

0:34 this hurt my soul

[@isaacscharpf3607]

Andrius Daraškevičius same

[@higorcosta2856]

O celular dele tava inteiro no início do video. Quando finalizou o celular tava trincado justo onde fica preso kkk. Tem um risco ai Like

[@dextermorgan8218]

No secure at all. That's a waste! Only works on KZbin not real life.

[@jmalvika]

too much work, would just buy

[@dial2277]

It's just an idea.