I set this card up with three external stepper drivers for my homemade 3 axis CNC machine. I'm using open builds control to test everything and it seems to be all working correctly. I'm wondering if I need to supply the board with 5 volts if it's not connected to USB? Or does it get all of its power from the 12-volt connector?
@ytskt3 ай бұрын
How are you buying it in India?! Or is there any Indian supplier?
@pierpa_76pierpaolo4 ай бұрын
But here there are two "Y's" and not XYZA . How do I solve on the software? Thank you very much.
@Basement_CNC3 ай бұрын
you cant, its a hardware limitation, since it only has 3 driver ports, and the 2y outputs are both connected to the same driver, so gantry squaring wont work either
@roberthosking75243 ай бұрын
What is "S" axis? I noticed mine jumped to 50 today. Weird.
@dacianfd84187 ай бұрын
I can use this board with the draw cnc ?
@skurniyantomappadang4 ай бұрын
can this board use for 10 watt optical power for laser diode? thanks
@user-mq2ws6rh2s3 ай бұрын
Можно ли подключить к этой плате старый offline contriller с кнопками?
@africanhubza2 ай бұрын
how do you set a zero point to start from
@aqwamnasimbada13519 ай бұрын
Can we add relay for automatic spindle switch?
@xandi32052 ай бұрын
would this work for the 2D Pen Plotter with all the same feature or is it just for laser engravers
@sash-v7i2 ай бұрын
Think yes if you're machine work with G-code commands.
@AnzAnnGaming9 ай бұрын
Can you share the stl file for the case?
@MineOrebaker8 ай бұрын
I am having a problem like once I connect my msk laser tool for wifi and after that If I disconnect the power then my board is not connecting again I'll have to connect the board and reconnect for software while plugging so there is any to skip this ?
@douglaslim9927 ай бұрын
Maybe you can try to reflash the firmware back to 2.10 or 2.08 as shown in the video
@Island.dweller10 ай бұрын
thanks
@jj84828 ай бұрын
does lightburn work with this??
@jwrtiger7 ай бұрын
The TwoTrees Laser I have uses the same board less the display board. I have no problem using the latest version of LightBurn.
@AbdullahKhan-vb1xr5 ай бұрын
please can you tell me about the wiring of the nema17 with mks dlc 32v2.1. I am facing issue with the running of the motors with the board.
@sash-v7i2 ай бұрын
Do you put driver boards on main board? They are sale separately in some offers.If yes check is they right connected to the main board. If yes you need data sheet for Nema motors to see what pin for what is. Good luck 🤞
@glennmartonic63766 күн бұрын
@@sash-v7i would a cnc shield work with this board to drive the nema 17 steppers
@akhmadabai77874 ай бұрын
if wifi setting installed are can still use in Lightburn?
@sash-v7i2 ай бұрын
Yes,go to Lightburn in settings and re-add laser again with wi-fi connection.
@zaffy0014 ай бұрын
Hi sir can you please give case stl files. Dlc32 board case.
@flopesff11 ай бұрын
I am having an issue using this board. During the milling, the Z axis is going down. Do you know what happening?
@Basement_CNC4 ай бұрын
it is probably the forces of the endmill pulling down on the z axis, and the stepper isnt strong enough to hold it in place. mayby try a straight flute or downcut endmill, the dont produce that much force pulling down
@DearChina13 ай бұрын
Change Your stepper motor ,I got the same issues last month
@flopesff3 ай бұрын
@@DearChina1 The issue was solved? Did you use some special stepper motor?
@DearChina13 ай бұрын
@@flopesffno just replace with the same,yes isssues was solved
@amdadulhaque46257 ай бұрын
Does it support Lightburn?
@jwrtiger7 ай бұрын
The TwoTrees Laser I have uses the same board less the display board. I have no problem using the latest version of LightBurn.
@Hollywood4Fun3 ай бұрын
Why doesn't the mobile app have z-axis?
@abhayvk831024 күн бұрын
Because the app is for laser, and laser do not use z axis
@Hollywood4Fun24 күн бұрын
@@abhayvk8310and yet he says it's for any CNC machine that needs x y and z axis control.
@Hollywood4Fun24 күн бұрын
@@abhayvk8310my understanding is that makerbase used to offer z-axis control in their app but they removed it. I think if you sell a card that is supposed to control x y and z axis then you should have an app that can control x y and z axis.
@frankhovis10 ай бұрын
You realise there is almost NO support for this board and the last firmware update was a year ago?
@silverify3 ай бұрын
Which board do you suggest to buy?
@andrikurniawan5313 ай бұрын
up
@omKumbhar54811 ай бұрын
Where to bay this full kit in chip price😊
@jwrtiger7 ай бұрын
Aliexpress, usa, Both the control board and the display board for less than $20.00 USD.
@silverify3 ай бұрын
@@jwrtigerboth for 19, cant find that.. You mean together about 40 $?
@Robert4390a7 ай бұрын
my dlc32 v2.1 board does not auto connect to wifi
@JuiceWrId_9997 ай бұрын
L
@JuiceWrId_9997 ай бұрын
Mine does😂😂
@douglaslim9927 ай бұрын
Which version of firmware you installed, the latest 2.30 was disable that Wifi autoconnect feature temporarily, to fix some bugs…if you want it back, best to flash the older version, 2.10 or 2.08
@venko321110 ай бұрын
If possible to use for CNC router
@JuiceWrId_9997 ай бұрын
Yes
@JuiceWrId_9997 ай бұрын
It’s labeled as a cnc laser machine you just connenet a spindal to the port that says spindal
@koolkiwikat10 ай бұрын
thank you for sharing, can you share the file for the case
@ataullahpersonalvideos693911 ай бұрын
How may i contact u
@nachogarcigmailcom11 ай бұрын
I can use this board and program it with the arduino environment?
@SuperbTech11 ай бұрын
you dont need to program it, it has built in firmware. you can directly use it using GRBL controller
@douglaslim9927 ай бұрын
Basically it is in Arduino environment , with a integrated cnc shield.