Mechanical Engineering Technical Interview Questions And Answers | Mechanical Engineer Interview

‪@superfaststudyexperiment‬ Mechanical Engineering Technical Interview Questions And Answers | Mechanical Engineer Interview.
Hello Friends
I am Tarun Verma Welcome to Our KZbin Channel "Superfast study and Experiment"
About This Video
In this video we discuss On Mechanical Engineering Technical Interview Questions And Answers . Selected Top interview Questions And Answers for Mechanical Engineer which is Frequently asked in Interviews for Experienced & Fresher Candidates.
I hope you like it.
Your Queries
Mechanical Engineering Technical Interview Questions And Answers
Interview Questions And Answers for Mechanical Engineer
Top Interview Questions And Answers for Mechanical Engineer
Frequently asked questions and answers for Mechanical Engineer
Mechanical Fitter Interview Questions And Answers
Technical interview Questions And Answers for Mechanical Engineer
Mechanical fitter technical interview question and answer
Top Mechanical engineering Interview Questions and answer
Top Mechanical fitter interview questions and answers
Mechanical engineer preparation for job interview
Mechanical engineering technical interview questions and answer in hindi
Mechanical engineer technical interview questions in hindi
#MechanicalEngineerInterview
#MechanicalTechanicalInterview
#MechanicalEngineerJobInterview

[@sambhau...1547]

module= inner pitch circle diameter / no of teeths M=D/T M=300/60 Module=5mm

[@superfaststudyexperiment]

Correct Answer

[@kaziashfaq9809]

Correct 💯

[@bhagabatbehera2222]

But practically D=300 T= 60 M=5 Kabhi nhi hoga 310/60=5 correct

[@aligadoor9792]

Asambao😂

[@kuaa2458]

Ye 58 teeth ka hai 60 teeth pr 4.75 aye ga

[@mdkasid3970]

Thank you aap video k wajah se mere interview pass ho gaya😂😂😂

[@superfaststudyexperiment]

Great brother 👍 Kahan selection hua hai

[@trishnakayal8372]

Mari v aj selection hua h....

[@dheerajyaduvanshi3561]

@@trishnakayal8372 where?

[@trishnakayal8372]

@@dheerajyaduvanshi3561 Durgapur

[@trishnakayal8372]

@@rebeltarfarhn8748 Aise q bol rahe ho? Kya help chahiye boliye...

[@RajuSingh-kb1wb]

Thank you for info, As per your last question's answer its that Module=D/T(300/60=5)

[@superfaststudyexperiment]

Correct Answer

[@AnkushKumar-pb5zc]

Bhut easy question h😅

[@surajingale6109]

Module=Pitch circle dia/no of teeth Module=300/60=5

[@superfaststudyexperiment]

Correct Answer

[@_johar_king___]

Mera कल इंटरव्यू हे इसलिए vidos देखने आया हो ❤❤ ओर kon कोन देख रहा है❤

[@superfaststudyexperiment]

Best of luck 👍 interview hone k baad jarur bataiyega ki apka interview kaisa gaya. Aise hi aur bhi bahoot sare video mere channel k playlist Mechanical fitter and engineer interview questions and answers me hai

[@_johar_king___]

@@superfaststudyexperiment ha

[@jatinhooda8018]

Mera bhi kll interview h dkhte h kya rhega

[@_johar_king___]

@@jatinhooda8018 ho gya ki nhi ap ap cliyar

[@_johar_king___]

Mera to acha gya thaa interview

[@ajaybaghel.5396]

M = D/T 300/60=. 5ans Very imt video for mechanical engineer sir Thanks for this video 🙏🙏❣️

[@superfaststudyexperiment]

Most welcome

[@akbtechnical3682]

This video is very interested me thanks for giving me knowledge At lost Answer is 300/60 =5 🙏🙏🙏

[@superfaststudyexperiment]

Most welcome brother please subscribe there are number of such type of videos in this channel.

[@anantanarayanpatra7096]

Thank you so much sir ...this is a very ionic explain .... Module=D/T(300/60=5)

[@superfaststudyexperiment]

Thanx for watching please subscribe there are number of such type of videos in this channel.

[@Mukesh-5897]

Ryt

[@dhananjybhagat2937]

Module= 5

[@fatihtasdelen4701]

Plz help me its vital How to convert 220 volt 150-200 hertz alternator output voltage to 50-60 Hz Will the frequency converter do the job? THXxxx

[@jharkhandivlogs..1956]

Module=Pitch circle of diameter/no.of teeth M=D/T =300/60 =5

[@superfaststudyexperiment]

Correct Answer

[@vamanmengal5052]

Module=pitch of diameter/number of teeth M=? D=300,T=60 M=D/T =300/60 =5 So M=5

[@superfaststudyexperiment]

Correct Answer

[@nasirhussain5876]

Module=pitch of diameter/number of teeth M= ? D= 300 T= 60 M=300/60=5 M= 5

[@LUCKYCREATIONS42]

Tq for this wonderful information And last question answer M=d/t M=300/60 M=5

[@superfaststudyexperiment]

Absolutely correct Answer

[@siddumoosewala5824]

Module of gear,M=D/T =300/60 =5mm Ans

[@superfaststudyexperiment]

Correct answer

[@ajeetgautam9843]

Module = pitch circle diameter /number of teeth M=D/T M=300/60 M=5

[@superfaststudyexperiment]

Correct Answer

[@sachintiwari6453]

@@superfaststudyexperiment sir 5 kaise aaya

[@ankitpgond9321]

Bhai mene BTech mechanical kiya tho skill me computer knowledge mangte hey kya or skil bhi managte hey kya sir

[@superfaststudyexperiment]

Basic computer knowledge is sufficient. For designing related firms you have a good knowledge of,cad,catia,proe etc like designing software.

[@funnyfoul2465]

I'm very much inpressed and by watching this video i subscribed your youtube channel

[@superfaststudyexperiment]

Thanx for watching stay connected brother ❤️❤️❤️

[@anjaykumar8547]

@@superfaststudyexperiment good

[@BudhKoushi]

Very helpful video bhaiya least count of verniyer & scew Guage

[@SARVJEETSTUDYPOINT]

T = rd/nt So , T = 300/60 5mm

[@superfaststudyexperiment]

Correct Answer

[@aduisaac7618]

this is very important video, keep uploading

[@superfaststudyexperiment]

Ok brother There are number of such type of videos in this channel Please check channels playlist Technical Interview Questions And Answer For mechanical fitter/Engineer

[@anishmahanta1678]

module = pitch circle diameter /number of teeth M=D/T M=300/60 M=5

[@superfaststudyexperiment]

Correct Answer

[@rahimdeshmukh5965]

Module =D/T(300/60=5) Backlash=0.06×5=0.3 Root clearence=0.3×4.5=1.35

[@nikkeesamy46]

Ans. Module= D/T =300/60=5 thank u sir for this video

[@superfaststudyexperiment]

Most welcome brother

[@harshv5512]

Bhut hi helpful vdo hai mere sare doubt clr ho gye, thanku 🤓

[@superfaststudyexperiment]

Most welcome brother ❤️❤️❤️👍

[@javeedhvactechnician7760]

kzbin.info/www/bejne/j5vQfISoorB3msk

[@latestfilmcollection1314]

Learn easily how to differential gearbox works..👇👇👇👇 kzbin.info/www/bejne/b6qtYntpaM-tgrs

[@golammostafakhan8652]

Very good mechanical super visor ka question & answer Jada korke dijiye.

[@lbcreation2422]

Module =D/T (300/50=5) is answer . Thank u so much sir for this video ..

[@superfaststudyexperiment]

Most welcome brother there are number of such type of videos in this channel

[@Gmail.come1000]

@@superfaststudyexperiment galat hai tumhara bhag

[@prasantakumarbehera488]

300/50=6

[@manikandanmadhuvappan8166]

Super bro . I have a doubt about what are the numbers 220,320&460 you mentioned in oil used in industrial gear boxes indicate

[@superfaststudyexperiment]

It's grade of oil

[@manikandanmadhuvappan8166]

@@superfaststudyexperiment thanks bro

[@superfaststudyexperiment]

@@manikandanmadhuvappan8166 most welcome brother

[@latestfilmcollection1314]

Learn easily how to differential gearbox works..👇👇👇👇 kzbin.info/www/bejne/b6qtYntpaM-tgrs

[@rohanpawar3899]

92 no also use

[@HaritGaithal]

Nai sal mechanical se polytechnic kar raha hun isliye yah video dekhne ke liye aaya hun❤😅😮😮🎉

[@superfaststudyexperiment]

👍 great

[@parmarnilesh13273]

Module - 300/60 = 5

[@awdheshkumaryadav6299]

Module = 300/60. =5

[@mjshaan08]

Thank you sir aapke video ke vajaha se mera ho gayaa ❤

[@superfaststudyexperiment]

Congratulations Kahan selection hua hai bhai

[@mjshaan08]

@@superfaststudyexperiment Toyota sir

[@superfaststudyexperiment]

@@mjshaan08 great so happy for you brother ❤️❤️❤️

[@mjshaan08]

@@superfaststudyexperiment 1 year ka trainee hai sir

[@bapisingh2526]

Sir I want to know about the soap company machine name , machine works, machine installation.

[@superfaststudyexperiment]

Sorry brother I don't know about that

[@rushikeshmate4915]

Your video's are very helpful to us 🔥🔥...can you make video on mechanical design engineer

[@latestfilmcollection1314]

Learn easily how to differential gearbox works..👇👇👇👇 kzbin.info/www/bejne/b6qtYntpaM-tgrs

[@shishirkumarsatapathy8972]

Sir your explanation in mechanical equipments are very good and any one can understand this clearly... If you have time then please explain about Inside Instruments of hydrolic motors and about power pack in hydrolic system.....

[@superfaststudyexperiment]

Ok

[@latestfilmcollection1314]

Learn easily how to differential gearbox works..👇👇👇👇 kzbin.info/www/bejne/b6qtYntpaM-tgrs

[@sudiptanandi3965]

0.02mm

[@sudiptanandi3965]

0.01mm

[@sudiptanandi3965]

5

[@shariqafridiafridi1673]

Sir Vernier caliper Ka least count 0.1 hota ha.

[@rajunkr4410]

M=pitch circle dia m/number of teeths M=D/T M=300/60 M=5(module)

[@superfaststudyexperiment]

Correct Answer

[@hemachaturvedi6688]

Module= pitch circle diameter/no. Of gear teeth = 300/60 = 5

[@superfaststudyexperiment]

Correct Answer

[@ranvijaynishad4671]

M=d/t 300/60= 05

[@sushantbiswal]

Module=Pitch circle diameter/number of teeth M=D/T M=300/60 M=5mm

[@superfaststudyexperiment]

Correct Answer

[@sirinakhondoker5049]

T=60,D=300mm,M=? According to law, we know that, M=D/T or, M=300/60=5mm Final answer Module=5mm

[@mohitverma4744]

Thanks sir for a wonderful video ☺️

[@superfaststudyexperiment]

Most welcome brother There are number of such type of videos in this channel.

[@latestfilmcollection1314]

Learn easily how to differential gearbox works..👇👇👇👇 kzbin.info/www/bejne/b6qtYntpaM-tgrs

[@UMESurajKumar-lz9vd]

thanks bro, now i am placed with the help of your video.. 🤗

[@superfaststudyexperiment]

Great 👍 brother congratulations where you are placed.

[@heartkingstatus8974]

Kaha

[@pruthvirajdas1805]

Modul=5mm

[@samtech435]

M=d/t M=300/60 M=5

[@superfaststudyexperiment]

Correct Answer

[@vimaleshpatel683]

Module = pitch circlr dia / no teeth module= 300/ 60= 5

[@superfaststudyexperiment]

Correct Answer

[@pradeeppanchal6597]

M=D/T So module is 5

[@rakshithgowda7665]

What is stress and strain? How are they related? Explain the difference between tensile stress and compressive stress. What is the Young's Modulus (Modulus of Elasticity)? How is it defined? Define Poisson's ratio and explain its significance in material behavior. What is the difference between brittle and ductile materials? Can you provide examples of each? Explain the concept of shear stress and shear strain. How is bending stress different from shear stress? Describe the process of calculating the maximum bending moment and shear force in a simply supported beam loaded with a point load at the center. What is the difference between axial load, shear load, and bending load? Explain the terms "yield point," "yield strength," and "ultimate strength." Discuss the importance of stress concentration in engineering design. How does the presence of notches or cracks affect the stress distribution in a material? What is Hooke's Law? Under what conditions is it applicable? Describe the behavior of a material under elastic, plastic, and elastic-plastic deformation. Explain the concept of fatigue failure and how it differs from other types of material failure. What is the significance of the S-N curve in fatigue analysis? Discuss the concept of creep in materials subjected to prolonged loading at elevated temperatures. Explain the difference between static and dynamic loading on a material. Describe the Mohr's circle and how it is used to analyze stress states. How does temperature affect the mechanical properties of materials? What is stress and strain? How are they related? Explain the difference between tensile stress and compressive stress. What is the Young's Modulus (Modulus of Elasticity)? How is it defined? Define Poisson's ratio and explain its significance in material behavior. What is the difference between brittle and ductile materials? Can you provide examples of each? Explain the concept of shear stress and shear strain. How is bending stress different from shear stress? Describe the process of calculating the maximum bending moment and shear force in a simply supported beam loaded with a point load at the center. What is the difference between axial load, shear load, and bending load? Explain the terms "yield point," "yield strength," and "ultimate strength." Discuss the importance of stress concentration in engineering design. How does the presence of notches or cracks affect the stress distribution in a material? What is Hooke's Law? Under what conditions is it applicable? Describe the behavior of a material under elastic, plastic, and elastic-plastic deformation. Explain the concept of fatigue failure and how it differs from other types of material failure. What is the significance of the S-N curve in fatigue analysis? Discuss the concept of creep in materials subjected to prolonged loading at elevated temperatures. Explain the difference between static and dynamic loading on a material. Describe the Mohr's circle and how it is used to analyze stress states. How does temperature affect the mechanical properties of materials?

[@superfaststudyexperiment]

First of all These questions were frequently asked in interviews That's why thousands of people watch it and like it. If you know all the questions why you are searching for videos. और Chutiya Questions kya hota hai bhai Ye to Tumhari Soch hai. Jaruri ye nahi ki tumhare hisaab se agar koi cheej nahi hai to vo chutiya ho jaye Jara baki ke niche k comments bhi padh Lena is video k

[@SON_OF_GOD_05]

Aaj interview hai bhai tmhri vdo dekh rha hu ....dekhe kitna sawal pucha jaaega isse

[@superfaststudyexperiment]

Best of luck for your interview Interview k baad jarur btana

[@asgharali9296]

Very nice sir plz isi tarhan ki r bohot c interview related r technical videos banain main aap ki videos bohot zyada daikhta hun and plz if possible kuch design side ko bhi cover karain means important calculations. thanks!

[@superfaststudyexperiment]

Ok brother aap channel k playlist "Mechanical Fitter / Engineer interview Questions And Answer" Par aur bhi aise hi videos dekh sakte hai.

[@latestfilmcollection1314]

Learn easily how to differential gearbox works..👇👇👇👇 kzbin.info/www/bejne/b6qtYntpaM-tgrs

[@yashbhosale2684]

Module = pitch circle diameter/no of teeth So 300/60 =5 Ans :- Module=5

[@superfaststudyexperiment]

Correct Answer

[@SandeshMali-z4u]

Pitch Circle Diameter : 300 mm No. Of Teeths : 60 Module of Gear = Pitch Circle Diameter (PCD)/ No. Of Teeths Module of Gear = 300/ 60 Module of Gear = 5mm

[@superfaststudyexperiment]

Absolutely Correct Answer

[@astopnoremix6972]

Module =D/T ,300/60=5 ans

[@WorldTechIndia]

D= 300mm T= 60 300/60 = 5 Module Is = 5

[@superfaststudyexperiment]

Correct

[@WorldTechIndia]

@@superfaststudyexperiment Thanks Sir For Replying

[@ChandanSingh79326]

Module of gear ⚙️ is 5 mm 😅

[@superfaststudyexperiment]

Correct answer

[@TraderLalbihari]

Module 5 thanks for guidelines

[@superfaststudyexperiment]

Correct Answer please like and subscribe there are number of such type of videos in this channel

[@kumargourabsarkar9767]

M=5(D/T) 300/60=5

[@superfaststudyexperiment]

Correct Answer

[@piyushmechanicalengineer8702]

End of this vedio , You ask one qus. That ans is 5 module.

[@superfaststudyexperiment]

Correct Answer

[@shaileshprajapati9230]

M=D/T M=300/60 M=5MM

[@jayvardhandesai2709]

O keshe ceculet kiy

[@AbhishekKumar-zu6tg]

A Vernier scale on a caliper may have a least count of 0.1 mm while a micrometer may have a least count of 0.01 mm.

[@mdjavidkadli7067]

Gear module M=P/N T. 300/60=5

[@superfaststudyexperiment]

Correct Answer

[@ayushchaturvedi4297]

आप बहुत गजब पढ़ते हैं लग्जरी वाली लयक पढ़ते हैं जो हम लोगों को चाहिए हम लोगों को बहुत बढ़िया समझ में आ रहा है जो आप वीडियो के मध्यम से समझते हैं धन्यवाद यू वेरी मच सर

[@superfaststudyexperiment]

धन्यवाद मित्र 🙏 वीडियो को लाइक जरुर करा करे

[@viveksony8165]

Module of gear = Diameter of pitch circle/ Number of teeth = 300/60 =5 ans.

[@superfaststudyexperiment]

Correct Answer

[@misteratom2022]

M= D/T =300/60=5mm ans.

[@superfaststudyexperiment]

Correct Answer

[@eyuptayfunyldz7240]

Thank you very much, it would be really good for sharing English videos after that. I’d really like to watch every video you have sent

[@latestfilmcollection1314]

Learn easily how to differential gearbox works..👇👇👇👇 kzbin.info/www/bejne/b6qtYntpaM-tgrs

[@kumars_creation7064]

I am very happy sir your concept ..♥️♥️♥️

[@superfaststudyexperiment]

Thankyou brother stay connected

[@latestfilmcollection1314]

Learn easily how to differential gearbox works..👇👇👇👇 kzbin.info/www/bejne/b6qtYntpaM-tgrs

[@tapanbarik8201]

Good

[@superfaststudyexperiment]

Thanks

[@luxurylife9813]

M=D/T M=300/60 M=5MM

[@superfaststudyexperiment]

Correct Answer

[@IDITHANGIchannel]

Wonderful explanation💯 👏🇮🇳

[@superfaststudyexperiment]

Thanx brother There are number of such type of videos in this channel.

[@HarishKumar-np6xw]

Module=D/T M=300/60 M=5mm

[@superfaststudyexperiment]

Correct answer

[@milajulaknowledge8212]

Pitch diameter=300 No of teeth=60 Modul=? M=D/T=300÷60=5 M=5 Ans

[@superfaststudyexperiment]

Correct Answer 👍

[@javeedhvactechnician7760]

kzbin.info/www/bejne/j5vQfISoorB3msk

[@johnson3252]

Thank you so much sir for explaining... This is so informative vedio I like it ✌️ D=300 T=60 M=? So M=D/T , M=300/60, or M=5 Answer ☺️

[@superfaststudyexperiment]

There are number of such type of videos in this channel

[@ajazmohammad9398]

5

[@mohdshami2105]

5 is correct answer

[@umeshpatel9465]

Sir module 5mm hoga iska 😍 thankyou sir.

[@superfaststudyexperiment]

Absolutely correct Answer

[@DR-se5ng]

👍👍👍👍

[@latestfilmcollection1314]

Learn easily how to differential gearbox works..👇👇👇👇 kzbin.info/www/bejne/b6qtYntpaM-tgrs

[@nabakr.kalita7203]

5

[@karangaikwad8352]

M=Pitch dia. /no of teeth M=300/60 =5

[@superfaststudyexperiment]

Correct Answer

[@kamparajuravishankar3254]

Bro top 15 questions on hydraulics

[@superfaststudyexperiment]

Ok brother

[@kamparajuravishankar3254]

Weldings paina koodaaa interview questions choodu

[@azazansari6087]

Love you sir ...

[@superfaststudyexperiment]

Love you too brother

[@AFFARMY138]

Mai I'd card kaise banaya ge bike mechanic Hu or hum ko I'd Bana ha

[@superfaststudyexperiment]

इसकी जानकारी नहीं है मित्र

[@KMthink]

Module=inner PCD/No. teeth M=D/T M=300/60 Module=5mm

[@pradeepmahawar5668]

M=D/T =300/60 =5mm Ans

[@superfaststudyexperiment]

Correct answer

[@roshanmankar8245]

module= pcd/no.of teeth m=300/60 m=5

[@superfaststudyexperiment]

Correct Answer

[@stereoheart7]

Module=5, thank you sir!

[@superfaststudyexperiment]

Correct Answer most welcome

[@SohelUddin-xq8kj]

Modules 5 hoga

[@sumeerkaul2811]

MODULE =PCD(PITCH CIRCLE DIAMETER)/NUMBER OF TEETH ON GEAR ,SO MODULE =300/60=5mm

[@superfaststudyexperiment]

Correct answer

[@Shub_rider]

Bhi yr same question puxa tha muje interview m yr 💯😱😂

[@superfaststudyexperiment]

Aur bhi aise bahoot sare videos hai brother channel me jaha se aap prepration kar sakte hai

[@Shub_rider]

Ok

[@neerati.thirupathireddy7703]

Telugu lo cheppagalaru

[@kalleshwarbalsure1645]

Module =inner pitch circle diameter/no of teeths M= D÷T = 300/60 =5mm

[@superfaststudyexperiment]

Correct answer

[@rakeshsingh2250]

Ekkal Tu D upon t so 300 upon 60 equal to 5 mm

[@superfaststudyexperiment]

Correct Answer

[@askanibaloch4382]

Module=pitch circle diameter/number of Teeth M=D/T M=300/60 M=5mm

[@superfaststudyexperiment]

Correct answer

[@Himanshu70652]

module=D/T=300/60=5 answer

[@superfaststudyexperiment]

Correct Answer

[@nirmal-shorts-creators70]

Last question k module - 5 Hoga

[@superfaststudyexperiment]

Correct answer

[@neerajbhandari9004]

Least count of vernier caliper is 0.1mm not 0.02 😂

[@superfaststudyexperiment]

Mechanical vernier Least count is .02mm .

[@TheHopelessVoid]

Vo ideal case me 0.01 hi hota hai but manual me kuch na kuch error hota hai jiski vajah se manual vernier caliper me 0.02 hi lete hain

[@ganeshsingh3923]

Module=pitch circle of diameter/no.of teeth M=D/T=300/60=5

[@superfaststudyexperiment]

Correct answer

[@Official_stetus_views]

300/60=5 module is right

[@superfaststudyexperiment]

Correct answer

[@devendrasinghraospirituala8619]

Nice video

[@superfaststudyexperiment]

Thanks

[@karanbhagat5727]

M=D/T M=300/60 M=5mm

[@superfaststudyexperiment]

Correct Answer

[@KIRANKUMAR-dk7ry]

M=D/T(300/60)=5 is answer . Thank u sir

[@superfaststudyexperiment]

Correct answer

[@AbhishekChauhan-q3q]

60×300=5 Very interesting video sir thank you so much sir ❤❤❤❤❤❤❤

[@superfaststudyexperiment]

Most welcome there are number of such types of video in this KZbin channel

[@Raju7937]

pitch circle diameter (mm) D = 300 mm number of gear teeths T = 60 module M = D/T M=300/60 M=5 mm

[@superfaststudyexperiment]

Correct Answer

[@kuaa2458]

But teethS 58 aye gy es dia metar main

[@mbbsatul1]

5mm

[@superfaststudyexperiment]

Correct Answer

[@ZafarIqbal-no2on]

module=d/t 300/60=5 answer

[@superfaststudyexperiment]

Correct Answer

[@ismaelshaikh9532]

M=D/T M=300/60=5 M=5

[@superfaststudyexperiment]

Correct Answer

[@vipinyadav3551]

Module=5mm is the correct answer

[@superfaststudyexperiment]

Correct Answer

[@MH_19Gaming]

M=D/T M=300/60 M=5

[@superfaststudyexperiment]

Correct Answer

[@MH_19Gaming]

Thanks sir