Support & Target

[@gamingSlasher]

Happy to see that Keith is still holding up.

[@randallparker8477]

Well planned and executed, as usual. Awesome lessons to be had.

[@bcbloc02]

Their maintenance must be pretty on point that looked pretty corrosion free for a salt water heat exchanger.

[@KG-yn9qi]

Keith Thank you for working and posting on KZbin ! Long time viewer.

[@jonathanoseredzuk3892]

Nice trick with the spring loaded center 👍🏻

[@rexmyers991]

Looking forward to your visit with Keith Rucker

[@Nanotick1]

Thank you for sharing your knowledge.

[@Hoaxer51]

Gotta do something to keep the lights on! Lol Thanks for sharing, we’ll take whatever you got.

[@jameswood9764]

America has to get more manufacturing jobs brought back to America!!!

[@BrooksideFarmBarreMA]

Absolutely. And you don't have to worry about port issues with American products, either.

[@fainderskurs-koi8767]

Вопрос. Где вы возьмете столько специалистов? Я конечно не знаю, когда у вас начали убивать производство, скорее всего, за долго до нас. Но исходя из нашего опыта, Когда в стране было, по меньшей мере, миллионов пятьдесят хороших специалистов и пару миллионов, супер профессионалов. То за тридцать лет, на территории бывшего СССР, ни осталось ни одного специалиста. Вернее, те кто остался, им по 60-ят лет, и им глубоко до лампочки, на это место проживания. Восстановить уровень невозможно. Новых научить, тем более. Просто не успеем. Токаря нужно учить лет пять, минимум. Остальных, еще больше. Слесаря ремонтника, он учится всю свою жизнь.

[@jimmyboles3409]

Thanks for sharing Kieth enjoy watching you use the k&T mill I have 2 of them and trying to get time to getting them set up to run lol! Busy, with other project jobs in the shop, liked you showing your setups

[@chieft3357]

I knew what you were doing when measuring the tap depth with the tap bottomed out but I'm not sure some of the viewers knew the importance of that measurement. I guess I like as much info as possible. That's just me. All the best to ya'.

[@seephor]

Looking forward to more Pearl videos

[@W4BIN]

I have put in hundreds of Heli-coils, before I retired, and all were dry with an ac powered hand drill and everyone of them were done dry. I slather cutting fluid on everything, but I never saw the need for cutting fluid (WD-40) in 5/8" thick aluminum with 3/8" through holes. Ron W4BIN

[@ducewags]

@W4BIN Where are the through holes in this video?

[@fredhoyt6900]

I like that you didn't use an electric drill.

[@grntitan1]

You got her done!

[@jondavidmcnabb]

That job seemed way way to quick but damn you probably made good money on it!!!!

[@scottjones7279]

Do you ever put a couple of drops of thread locker on your inserts?

[@KeithFenner]

No I don't

[@ÁREAJ27]

Olá amigo Keith,muito bom trabalho como sempre!!! Boa sorte!!!

[@ApukEldar]

👍👍

[@robertmardis6510]

Cool little trick with the tap follower.

[@robertmardis6510]

Thanks Keith 😃

[@joeylawn36111]

What did the big white part go to?

[@KeithFenner]

After cooler on a large marine engine.

[@joeylawn36111]

@@KeithFenner Thanks!

[@fainderskurs-koi8767]

Лайк.

[@mitchdenner9743]

What was that? Some kind of compressor?

[@KeithFenner]

After cooler for a large marine engine

[@RickBaconsAdventures]

imagine the guys that would do this with a cordless construction drill! Another great repair the way it should be done, better than new

[@markat9576]

What no comments yet? I guess I’ll be the first. Long time subscriber here. Thanks, Keith.

[@nickrandol9133]

That is a lot of stick-out, or cantilever…. Does that, or can it, flex your mill table? Or knock the gib adjustment off?

[@KeithFenner]

It was way less than the need to counter balance by hanging weight off the opposite side.

[@johnmcanulty7341]

Try walking around barefoot for exactly 5 seconds after removal and, I would bet you find a tab or three.

[@joeylawn36111]

😱😳😢 😉🤣

[@davidclodfelter7147]

Was that a super charger for pearl?

[@KeithFenner]

LOL

[@jtg2737]

I'm curious to find out as to how many "snowflakes" you have offended and have un-followed you due to your banner in the background? Me? I'm not offended at all, rather I admire your "cogones" in the area that you are in. God bless and stay safe!

[@grntitan1]

Stand up for what you believe in, even if it means standing alone. In this case, Keith isn’t standing alone.

[@jtg2737]

@@grntitan1 You're right. The silent majority is out there and they are scared of us.

[@waikanaebeach]

Keith’s politics are a matter for him. I choose to watch his videos because I enjoy them.

[@slausonm]

I supported Keith when he was going through problems with transferring to the new shop. I will admit his political views leave me scratching my head, but I often choose to stay in groups that I am not in agreement with most of the followers. He is an excellent craftsman who I can admire and disagree with.

[@KeithFenner]

I'm guessing, by looking at my analysts over the last year, around 2,000 If you visit other shops up and down the area here, you will see more of the same flags and stickers hanging proudly, but everyone comments on my photo collection. I also get more positive comments from walk-in customers than no comments. You can't argue facts and results!

[@tangoone6312]

.

[@dizzolve]

Did I miss what that thing is?

[@ducewags]

@dizzolve A cooler.

[@dizzolve]

@@ducewags o thx

[@frankdoner8402]

Thanks Keith!