Cheapest Ls Swap Turbo Kit Ever!

[@AlienTrashKitty]

Your hair @23:03 ... I didn't know I was bangin' a Backstreet Boy :P

[@callanbull]

I'm really digging the quality of your videos now Kyle. They're definitely becoming more viewer focused. Keep up the work, every video is even more enjoyable than the last!

[@Boostedlifestyle]

Thanks bro!

[@mweigt07]

I just binged watched this build for the past 5 days, how could you do this to me! Now I have to finish 1 of my seven projects with all of this sloppy mechanic motivation. Thanks for the videos that I can’t play that loud around my kids all the way from dumb old Texas. PS. All the cold jokes I can relate. I lived in Minot North Dakota for 9 years. -65f is really cold and I’m not ok with it.

[@Boostedlifestyle]

Whoa! You were on a mission

[@mweigt07]

Boosted Lifestyle well being a mustang guy that loves the LS it only made since. Wish I would’ve watched them as you posted as I could’ve helped with the cheap parts list as I had a turbo 5.3 Silverado(super cheap build)

[@gixxernut8021]

This is what I like the guys who can make it work from beginning to end awesome I say if it works is all that matters

[@christyeasley6235]

When u tig always get the tunkston as close as possible to have heat and flow control it needs to be almost touching. Art

[@xBarnabyJonesx]

The drill shuts off if its over heating. I usually chuck mine in the freezer or wrap in a cold pack, for a little while.

[@Boostedlifestyle]

It seems like the battery took a charge afterwards !

[@sjhdeh]

Try preheating cast in your oven to 500 degrees farenheit before trying to weld it. Works a lot better and helps prevent the cracking

[@Boostedlifestyle]

Yeah I just don’t want a smelly oven 😒

[@pokdher1]

You could heat it in your grill too

[@chuckwilke9875]

Use propane torch to preheat housing and keep as much of the housing hot as possible when welding cover with welding blanket to cool as slow as possible might try a griddle to put housing on while welding then cover with blanket and turn heat down slowly.

[@bash7teen]

nice to see a fellow canadian,, good content, cant wait to rebuild my hx52 for my 6.0 :)

[@strata99]

You can turn the drill bit around on the hole saw after you get a pilot hole and no need for extra equipment.

[@greenthumb858]

im a roofing contractor and i use all dewalt buy some 3x or even better what i use the 5x very expensive batteries but you will get tired of dealing with the small batteries

[@elijahnielsen2953]

hey man just a tip! see that solar panel looking thing right above where you look out of your welding mask? most if not all auto darkening helmets have a solar panel to charge your mask! just leave it in the sun for 10 mins and it should be charged enough and the rays from welding should charge it as well

[@jakelawson6552]

Tip for welding shields, cheap auto darks will perform up to there price. Either spend the money on a nice auto dark 2-300$ or just get a $30 passive lense shield and learn how not rely on autodark

[@howfast1078]

We're Diggin the content man! Keep it coming! I found you while looking for inspiration for our build! Good luck

[@Boostedlifestyle]

Hopefully I got you out to the garage!

[@howfast1078]

We're working on it! Should be at Grand Bend next year.

[@jamiemuncy2219]

Those hoods are posed to charge their self as you weld👍🏻 that housing is casted in what we compare it to pot metal, you need to try heating b4 you weld it and if that doesn’t work it’s probably not but you may get lucky👍🏻

[@chitwood73]

Same thing happened to me with my Miller hood. Turned out to be the battery contacts were corroded on one battery.

[@mattoneill9723]

I love your new adjustable hammer!

[@Boostedlifestyle]

I will quote myself “anything is a hammer”

[@BotelloPerformance]

sometime theres a grind mind, it kills the darkening function. mines on the knob on side and gets pressed when laying hood down

[@Eury9819]

why not tie the wastegate dump into the exhaust you just made instead of running a new pipe all the way down? and damn bro you getting good at welding!

[@Boostedlifestyle]

It would make too much restriction for our 3 inch down Pipe

[@motorbrains88chris]

Use some SS tig wire on the cast iron stuff and a little pre and post heat helps !

[@jayromas5385]

Pre-heat the cast bro and then weld firstly with cast stick rods then buff the weld and then tig on about 210 amps and you should be good

[@RollingInBoost]

what did you do in terms of the ecu

[@MTalib87]

Why not plumb the wastegate dump into your downpipe? this way you dont have to worry about running another pipe through the fender and out the bumper

[@Boostedlifestyle]

Because 3 inch is already too small 😂

[@MTalib87]

@@Boostedlifestyle Its 3 feet long lol. it isnt gonna cause much restriction.

[@gaberowe4318]

Can you send the link for the turbo kit? I got a ls1 Camaro I'm looking to boost

[@crushkrew]

Wait what? are we not supposed to put the WG on the housing now? Did you just revert for placement or other reason? Thx!

[@Boostedlifestyle]

It would work fine on the housing, the flange is a 44 on the housing though ! And I just installed a 60 and I wanted to show it off in the bay

[@johncoldwell340]

Little tip When your drill battery go flat let them cool right down before putting them on charge, and when there fully charged let them cool right down before using them even if they don't feel warm still let them still 4 at least 15mins and your batteries will last longer and hold a longer charge 👍, as long as the batteries haven't got blown cells already

[@Boostedlifestyle]

Yeah I might have smoked that battery 😂😂

[@YZFoFittie]

Great, so if you have a turbo or engine failure the oil goes right on your tires, GENIUS!!!!

[@Boostedlifestyle]

What. Look at every drag car the exhaust is out the side 😂

[@BoostEnvy]

Looking amazing, can’t wait to see some good passes on the track. And yes tig is a pain in the ass.

[@Boostedlifestyle]

It’s super fun though!!

[@BoostEnvy]

Very true, I have had a blast learning first hand on my hot side wouldn’t change a thing

[@kjetilbakke2138]

use 625 incornel filler rod for cast iron

[@betosgarage]

Great channel bro . I got my vsr billet 78/75 at home waiting for install . Looking for turbo manifolds that fit my g body , thyre pretty pricy tho

[@B4Lsoowoop]

So auto dark lenses do not play well with tig welding try a #9 or #10 gold mirror and it is a welding hood not a helmet I’m slightly concerned with where the helmet thing came from considering if I pegged you directly in the head with any object that welding hood would provide 1% protection only due to the fact that the clear lenses in your hood are z87 therefore your eyes would be “protected”. I love the content and thank you for teaching me about something I didn’t know maybe you can learn something from this.

[@mikereasoner4814]

Just curious why you didn’t leave the Wastegate on the turbo housing ? I don’t wanna learn the hard way if there is a reason

[@Boostedlifestyle]

It was a 44mm flange and I have a 60mm gate now

[@Stevesbe]

Your welding has come a long way 👍

[@WelcomeToTheMadness]

Why didn’t you just get a cap for that V-band port. Granted, more welding time...🤔

[@Boostedlifestyle]

I wanted to make it smooth again 😒

[@WelcomeToTheMadness]

@@Boostedlifestyle you're pretty good at welding now though. Stainless quickly annoyed me while messing with it.

[@ChrisSullivan69]

Nice! Whered you get the stainless for the downpipe?

[@Boostedlifestyle]

Amazon 😂 it’s just basic 3 inch pipe

[@justinmalone8518]

Get you an air hammer to get the pipes to fit those flanges better. All that filler is bound to break

[@brandonpanozzo86]

heck yeah comin along man good shit keep knockin it out cant wait to see how it works out

[@stinkymans5002]

Boosted Lifestyle would you happen to have the link to the turbo kit?

[@365hotfire]

Wish I could do this myself. Very nice!

[@shanewright6958]

Another great video 👍

[@Boostedlifestyle]

Thanks :)

[@callofgeorge]

what size is this turby again?

[@Boostedlifestyle]

7875

[@wadeellis67]

to weld cast iron, pre heat it in the oven for a couple hrs at 300-500* then torch the fuck out of it, glowing red. THEN you can weld. after welding peen the welds with a ball been hammer to relieve stress, then post heat it with the torch and throw it back into the still hot oven at 400 and slowly drop the temp over the next hr. let it soak in at 300 for an hr and then shut off the oven but leave the part in there to completely cool overnight. if its a big cast piece or your wife wont let you use the oven, a torch works just use tons of heat, seriously, TONS OF HEAT

[@Boostedlifestyle]

I guess I need a ton more heat 😂😂

[@OldSkoolF]

Were you using a Nickel rod??

[@james4wd236]

LS in a Ford.... Love it!!!

[@jasoncameron34]

Great video kyle love the hammer lmao. Love this mustang build

[@Boostedlifestyle]

I couldn’t find my hammer 😂

[@Cheezn4urdreams]

Kent.... about time

[@michealwriska2920]

Hey Kyle what’s the name of the Waze gates are using and do they have 60 mm in above I’m in the need for 2 60mm waste gates an I’m running out off moneys

[@Boostedlifestyle]

Blacksheepindustriesinc on Instagram 👌

[@tuffram2165]

Tip for holding something to weld Magnets various size

[@scottgoodwins]

Why don’t you buy another rear housing? If it’s cracking now surely the vibration and heat of the engine will be harder on it and make it more prone to cracking in the future.

[@Boostedlifestyle]

I’d rather buy a different turbo then

[@KD-jf9nd]

Project farm channel actually did a battery test of all different kinds of batteries. Amazon basic came out number 2 or something. And they’re cheaper.

[@Boostedlifestyle]

I never even thought about buying amazon batteries -.-

[@KD-jf9nd]

You’re always saying amazon is better for you in canaderp

[@ThePryapizmC]

$250 U.S. and shipping for you to practice making another?...I'll totally Rock a Boosted Lifestyle Log🤔

[@Boostedlifestyle]

Never 😂ww

[@alexmichal9413]

Kyle should have at least 100k subs

[@Boostedlifestyle]

I’m working on it!

[@mscottstone08]

Great content as always! 👍🏻.....get yourself a solar helmet. No batteries to replace!!

[@RDChanse]

a trick to fill bigger gaps use 2 rods and twist them together

[@Boostedlifestyle]

I ended up doing this for bigger gaps

[@TanksForTheMemories]

"good content kyle"

[@Boostedlifestyle]

Love it!

[@benjaminbaird1978]

He's gonna have boost creep bad because of the position of that Wastegate where it's at is fine but he's got it almost at a 90' it would be way better if it was more like 45'

[@Boostedlifestyle]

It’s like 30 deg off the flow of the manifold

[@FerociousPancake888]

Invest in a nice hole saw kit. It will change your life.

[@megabassbennylippo3760]

Lubricant is your friend with holesaws and steampipe

[@megabassbennylippo3760]

And you can get a plug for the wastegate flange

[@tylersteen2864]

What is that song

[@harryjohnson2]

Did you decide to keep the Supra? Another good video man, keep them coming!

[@CyborgbobaFett]

Nicely done Kyle! But why did I get adds for male enhancement during the video? haha. Must of used algorithm when you said you had a hard time filling gaps.

[@Boostedlifestyle]

Hahahaha because I use it obviously

[@TheMick26]

What's up, homie? First off, from the drill to the welding helmet, fuck all the batteries in this episode!🖕 Energizer bunny? Pffftt! You cant stop a good man from livin' that boosted lifestyle. 12:37 - Yay, you remembered!👏 Thanks for all the effort you put into making this video. You persevered through all the bullshit! That cross fit payin' off big.👊 One more thing, nice shirt. #teamraceteam🙌

[@jamiemuncy2219]

Nice video👍🏻 But there is a special place in HELL for people who LS swap Mustangs😱😱 I’m Ford to the core💯 You know a Yote swap would’ve been cheaper😱😱 And a SHIT TON FASTER 🤣🤣👍🏻🤣🤣

[@ryanstibora1351]

Lol we call that drill at work the wrist breaker. Hate that drill

[@Untensuru.]

Cool vid, but I didn't hear anything about this being the cheapest turbo kit in the whole video.

[@boogzwitdagoodz1523]

Dude great content minus the butthole part!🤣🤣🤣 TMI!!

[@Giftied]

thought you sold the supra?

[@joelmojica9271]

Is that a freakin mustang with an ls motor

[@betomedina3298]

Links to parts!

[@Murdertruckmafia]

What choo choo boy is that?

[@Boostedlifestyle]

Performance world 7875

[@Murdertruckmafia]

Thank u

[@turboman351w3]

DUDE THE HAIR CUT , WHAT THE HELL

[@Boostedlifestyle]

It’s the same haircut I’ve had for years

[@THRASHER1990]

Please buy a hammer lol

[@seanbailey317]

I thought he sold the supra??

[@Boostedlifestyle]

I did it’s awaiting pick up

[@MustangCrazyMan72]

Log manifolds aren't as good as tubular headers to a collector. I hope this log you've made exceeds all expectations.👍

[@fuzzdaddy9375]

Plz use a guard on that grinder and place the pipe in a vice. 😁

[@gixxernut8021]

Ho blooo

[@pepperoniunicorn8641]

Anybody who says guesstimate is a pea brain....

[@jersyboyy]

Badass. If you need a new shirt DM on IG @Streetcarsmatter and I'll hook ya up withnine of the new streetcar shirts

[@Murdertruckmafia]

Yeye

[@briangoudreau5793]

Hahahaha love the content and channel but sometimes you work like a caveman 🙈😳

[@Boostedlifestyle]

Of course I don’t know any other way 😂

[@briangoudreau5793]

Boosted Lifestyle Hahahaha I find myself doing the same thing you don’t realize it till you actually see someone else doing it

[@ericcompagnat]

Ton gaz trop élevé

[@BuckCity229]

Third!

[@wetsaltypickle]

Hell yeah!! I cant wait for the race between you and ruby!!