SURRON CHAIN DRIVE INSTALL

Installing the warp 9 chain conversion belt delete kit. No more ripping belts on the 72v surron moto setup. Enjoy ! Hope this helps someone.
Thanks to the sponsors of this video , companies with discount codes linked below!
Purchase Torp Tc500 use code HAWK5 for 5% off : www.surgestunt...
Use my discount code HAWK10 for 10% off your entire order on fastace.com
Use code HAWK5 for 5% off electrixebikes...
Use code HAWK5 for 5% off surgestunts.com
#surron #surronx #surronebike #surronwheelie #surronlightbee

[@viktorstanik]

Guys you dont have to take off swing arm, just fix it with screwdriver and do not hammer the swingarm bolt, it should go easy just wiggle it little

[@logan-taylor]

looking forward to hearing a full sound test - sounds better than other chain drives from that short clip but curious if it's still obnoxiously loud in person haha

[@JUSTINHAWKSMITH]

New video is live !

[@logan-taylor]

@@JUSTINHAWKSMITH you’re the man

[@JUSTINHAWKSMITH]

You are ! Thanks for watching !

[@Surron.joe69]

Hey man I got the chain drive installed but I can’t seem to find out what tension it should be set at

[@jamesbringle4446]

Hey, so I was in the same boat as you and Warp 9 said a quarter inch of slack.

[@shockadellick]

@@jamesbringle4446 It's past due, the LBX should have a Gear Box.

[@brandonbajc2084]

I bet by this time next year you'll have 100k+ subscribers!

[@JUSTINHAWKSMITH]

Thanks for the positivity man ! Appreciate it. ❤️

[@je7647]

IVE got one of these.last night it got too loose and is stuck against swingarm. ill take a look at this later try to get it out and tighten it by the screws you mentioned by the motor

[@JUSTINHAWKSMITH]

Hope you figure it out. Couple hundred miles on mine no issues yet

[@je7647]

yeah I like it, it was my fault for not getting it tigftened. I felt it loose knowing what was going to happen. ive done about 2k km on it

[@Overmotor]

Hell yea! Looks great man!

[@BenelliUpham]

Great video, really helped. Just wondered if the wheels are the standard size on this sur ron and if different just wondered what size you used for the bike, just cus they look chunky.

[@JUSTINHAWKSMITH]

They are a 19” front 16” rear. 90/100-16 rear tire size , 70/100-19 front tire size

[@Simnettnutrition]

Great tutorial man. How is the sound? I know this is supposed to be the quietest conversion, but how much louder than the belt would you say it is?

[@JUSTINHAWKSMITH]

Hey man I planned on including my thoughts on this , but my mic was not working good so audio was terrible. I will make a new updated video called “surron chain drive worth it?” Or something like that very soon. Cause this is something I really wanna talk about. But to sum it up it is noticeably louder yessir. But I will make a full video hitting more points and thoughts & have sound clips as well with good microphone. Soon. Thanks for watching !

[@Simnettnutrition]

Looking forward to it.

[@SurFrankenRon]

I just out one on right now. It's TERRIBLY loud and it was a pain in the dick to install. I had my motor super loose and the chain was fucked to get on

[@SurFrankenRon]

​@@JUSTINHAWKSMITHit's so loud that I'm questioning if it's installed correctly lol

[@JUSTINHAWKSMITH]

Make sure it is lubed good and you have the warp 9 setup… they are the quietest… also make sure your chain is not super tight it will be even louder ! Keep some slack in your chain. The motor-jackshaft chain. **Not your jackshaft to rear sprocket chain **

[@TomRoques]

What is the brand of your rear suspension, it looks strong and massive 💪

[@JUSTINHAWKSMITH]

Fast ace

[@alipsa823]

you help me a lot with how to remove the main gear with the puller tool, can you tell me please where to get this size of puller tool ? if in aliexpress it will be grat cuz i am from israel\palestine thx a lot ( i find only massive pullers) cant find this small you have

[@JUSTINHAWKSMITH]

I purchased it from advance auto part here in the US

[@TomRoques]

Incredible guy, your rear brake disc! Is it possible to have the link to buy one? Thanks

[@JUSTINHAWKSMITH]

It’s a “prickly” brand rotor

[@justinmanford5663]

Why didn't you show how you got the chain on? My motor is loose and I can't pull the chain together to connect the link.

[@JUSTINHAWKSMITH]

You rotate the motor in the motor mount adjuster slot with the bolts and it brings motor closer / further from the jackshaft pulley to make tension tighter / looser

[@chaosaddictz0072]

Do you have to put that circle metal circle thing for the bottom I don’t have that on mine but I see some people install them

[@malogocrazy7848]

Great video🔥

[@bikeninja956]

cool share brother... curious, what rear shock are you running?

[@JUSTINHAWKSMITH]

Full build video just uploaded going over the entire bike. But to answer your question the fast ace rear shock with 600lb spring ! Thanks for watching!

[@SurFrankenRon]

Dude what cover is that? I just tried putting my prickly back on after installing it, and it hits the chain. My motor is also adjusted all the way up because the chain is so damn tight, I can't adjust the motor any more than it is

[@JUSTINHAWKSMITH]

It’s just a cheap one off Amazon buddy ! Thanks for watching hope this helps.

[@lukevise7013]

Dose this work on the surron light bee X?

[@JUSTINHAWKSMITH]

@@lukevise7013 yes

[@surron_sefi]

You did it with no effort you must’ve had the right tools

[@JUSTINHAWKSMITH]

They’re not too bad at all to swap out. Hand full of tools nothing crazy. Wanna say roughly just needed a ratchet , set of Allen wrenches 13mm socket & 17mm socket.. everything on these bikes is either 13mm/17mm/19mm or 3mm Allen / 4mm Allen / 5mm Allen / 6mm Allen … thanks for watching hope this helped !

[@natevalis]

thank you bro i just subscribed 🫡

[@PNWSURRON]

You know you don’t have to take your swing arm off to do this. I did the same mistake.

[@JUSTINHAWKSMITH]

Do you just remove jackshaft thru the underneath ?

[@PNWSURRON]

Yes sorry for the long response just seen this😂

[@why...when...]

@@PNWSURRON what do you have to remove to take it out through underneath?

[@PNWSURRON]

@@why...when... nothing take the jackshaft bolt out and pull it out the bottom

[@why...when...]

alright thanks

[@oceunlimited1545]

First

[@skylarsadventures]