Suspension Leveling Calibration

[@Gsavage1]

Will be trying this tomorrow, if all goes well I will be ordering 12 sets of Ross - Tech

[@alhamedi66]

Thank you for sharing your experience with us. This procedures same to 2009 porsche cayenne

[@fernandoct6]

Hy there.. i have a 2008 touareg and i have a problem. I left the car on offroad mode and the next day i found it with the rear up (still on offroad) and the front down with the driver side even lower than the pax side (unbalanced). I started the car..started to raise up automatical and it drove fine... At night i left it in dynamic mode.. the next morning again the same isue..the rear was ok at the setting i left the car, but the front again with the same problem. The front lower than the rear and the driver side even lower!

[@motorcityspeedworks]

Gsavage1, it ended up being the Distribution Block near the compressor. That was the cause of the error message. Today I came out to 3 axles being on the ground and one rear at #3 height. The adaptation tries to level the car out, but after the pump runs for 60 seconds or so, it stops and the Ross-Tech screen says ERROR in red. I just threw $240 at a used control module...

[@TheRafalblog]

Thanks for video helpful I found front left wheel is 10 mm higher than right front wheel, can calibration can help in this circumstances?

[@compu85]

TheRafalblog yes, the calibration procedure will help with that.

[@justdoit6783]

Hi I'm doing a 2011 bentley mulsanne how do I kno the code for security access?

[@panamaya]

Do uncalibrated suspensions show as "level control" warnings on the dash? Or do the warning imply an actual hardware fault than needs repair?

[@mirekwolny4041]

Hi there To start to make all adjustments Allroad have to be on the first or second level? Thank You

[@jtfriedman]

I have the exact same Audi Allroad as in video. What level is the car supposed to be on? Is the idea the computer takes the measurements which are off and then readjusts to factory for each level?

[@vokez5297]

I am getting an issue where channel 1 will just display error not available, i have recently fitted a new ride height sensor so is there anything i need to do first?

[@jsmith05403]

This is suspension is not calibrated will this cause the suspension to fail and have the yellow and or read suspension light illuminate

[@a.ekram1]

can i use this method to calibrate dcc on my 2013 volkswagen cc

[@LeTRANSPORTEUR69]

*hello my Audi Q7 is very raised on the right side and crushed on the left side I can not calibrate it it always remains in the air I have so much value that I do not know what to enter do you have any idea how can we put it back to the factory?*

[@ekonomek88]

Is this procedure valid for Audi a7/s6 c7 model ?

[@Michael-Gould]

I keep getting a security rejected key error

[@robertferretti7990]

My 05 allroad thinks she rides at 422 not 402, is that common? In reality i have her sitting around 370.

[@allenchimunda4597]

Can i use for Porsche caynne 2005 for Height Calibration

[@Blackdogma]

Is this function available on VCDS lite? I need to re calibrate my Y reg, 2000 allroad

[@emredagyaran7494]

when i login and enter the adaptation menu, i wait for the "wait" to change into "Value" but is doesn't work. it just stops and says error. maybe bad sensors or something? can i just delete all the DTC and maybe then will work?

[@dirtyhands5646]

Did you ever find this one out ? Having the same issue.

[@kamatechnology7570]

Anybody knows the answer??? Pls help!

[@MaxDamage75]

@@kamatechnology7570 check 40 ampere fuse under driver seat...

[@diegod4752]

U using cable or icom????

[@BogdanescuX]

When I put the new value which for me is 526mm and press test it says invalid, not valid. Please help!

[@BogdanescuX]

And also on channel 5 it gives me error.

[@memesdedi]

Same here but the 5th channel doesn't show anything like it doesn't exist

[@mirkokolar1488]

Is the procedure same for audi A8 D3 2004

[@matejokadar8220]

Da

[@RossTechVCDS]

This info will apply to most non UDS level control systems, should work with 2004 A8.

[@atlanticbooking]

i have a touareg 2004 r5 and im getting ''stop fault running gear' when i drive a while. one of the pressure valve has been replaced since there was a leak but im still getting this message so i thought maybe the levels arent correct. do you think your video will help?

[@diegod4752]

Hey how are u doing? Nice video thanks for posting it. I got this suspension level malfunction message on my x5 e70 . My car is not leaning on one side i mean is more like lifted on one side u know what i mean? I got no leaks on the air bags . I think its more like something with the sensors or something like that. Do you think that with that program ill be able to fix it?

[@panamaya]

I am getting "Controller Refused Key" when entering code 31564. Any ideas?

[@uktech]

What setting does the suspension need to be on before the calibration? Lift, Comfort, Automatic or Dynamic?

[@mendez77054ify]

uktech 5 years??? Still no answer. From what it seems, probably automatic. When you enter on the first step on the vcds it adjust to set up height. Min 1:06.

[@mechspartans7051]

Auto mode

[@samgeorgebush9216]

@@mendez77054ify my rear air suspension doesn't work and it's very stiff.. will VCDS clear the problems or want to reset the full programming? Kindly guide me

[@MsFrankGS]

Salve, è possibile abbassare l'assetto su un A8 D3 del 2009 ? Se è possibile, come ? Grazie

[@cowboyfandallas2797]

what can go wrong with your car if this isn't done right ?

[@mertaslan6519]

Hi, I follow the steps. However at channel 5 message is : ERROR channel is not available how can i solve this. pls HELP. Already , Fault codes is 01437 :((

[@sandratramalalaalimahenina6605]

i got the same error

[@sorinsebastianheck6953]

Did you solved your problem? I have same and can't find the issue. Thanks

[@Wrofeel]

its this the same at Vw Touareg R5 2004?

[@RossTechVCDS]

Yes.

[@volodymyrg9300]

Hello what i need for VCDS

[@swissjetpilot1542]

Just to be clear - this seems to be specific for Air Suspension. Will this also work on Audi Magnetic Ride shocks as well or is that done through Address 14 - Susp. Elect.?

[@vcdsbyrosstech]

Old school air ride for systems that use the CAN protocol.

[@Gsavage1]

I see you didn't answer the last question about the error message but was wondering the same!

[@RossTechVCDS]

For this procedure to work, the vehicle needs to be to factory design. A leak in the system, wiring issues, bad sensors, ect can prevent one from being able to do the calibration.

[@diegod4752]

Do k have to use icom or can i o 8t using onlh cable? Nice video liked and suscribed.

[@keliremu6798]

I love you guys!!!!

[@muqimkhan623]

excellent just watched and do it love you sir

[@iridetriumphs]

when I access the Adaptation menu, it won't let me change any values, it just says error in the top boxes. Any reason for this? I need to calibrate my Allroad!

[@kaibintech]

Great video!

[@faizansiddiqui5113]

Can we do it In Skoda octavia 1.9tdi 2006..??

[@byPeITeeR]

:D wth

[@krzysztofczubachowski2530]

Czesc... S6 z nivo ogarnięta przez VCD....x zajęło to ok 40 minut

[@electrotiwine8782]

AJOUTE PAS PL

[@mdjahir5143]

Audi a6

[@dteague7037]

will this work on a 2002 Audi A4??