swash plate leveling 2014 by =wc= for Rc Helicopters

warning !!!! Do Not Use Subtrim to level your swash plate
adjust by linkages only if you have any issues or problems comment in the section below and we will help you

[@rickrodrigues2219]

Would I be correct in making this adjustment with (1) motor wires disconnected (2) Tx powered (3) Tx sticks in mid position (4) adjust servo push rods to just make contact with swash plate leveler? Thanks for reply.

[@wcwickedclown]

correct

[@JamesLewis-mp9zn]

Looked at a lot of videos on the subject. Yours is my center piece and most informative. Outstanding!!!!!!!!!!!!

[@4thGloryMonday]

great tutioral wc thumbs up buddy

[@vsjsysvbzhdgdb276]

Great sound

[@HeliMouse]

great info brother , liked

[@wcwickedclown]

thanks brother mouse

[@Appolloscott]

Thank u much

[@ezpzride7971]

appreciate that bro!

[@wcwickedclown]

no prob brother i remembered you needed this to

[@TheBeastFPV]

Nice video wc liked

[@wcwickedclown]

thanks Dee

[@DerredmaxTRIAX]

Thanks WC

[@williamgaines6356]

hello Thomas it's me Paul from Bronx New York. I have this problem. it's with my 450 and my 550 helicopter. every time I take off my helicopters tip over. Everyone says that it's because of an uneven swashplate and I believe them. from Bronx New York. I have this problem. Its with my 450 and my 550 helicopter............ Do I actually unscrew the.buckles from the swashplate.and adjust.them to.proper length at midstick or.do I go to subtrims on my transmitter and do it electronically? Because Everytime I go.to take off she tips over.and this can be frustrating. I swear i got everything down to a T. All my setup steps. All al. my parameter set-ups Everrrrry Thing. Please help me. I.am stumped Thomas and so scared to spin up my helicopter in fear she might tip over and do damage to my helicopter.

[@pauliether.c.guy.3349]

I love this guy's videos. He is my go to guy when im having issues no other guy matches his knowledge. I guess he was born with it in his blood. Keep up the good work Tom. I need to get a swash plate leveling tool for my 380 goblin which one do you recommend? and where can i get it? Thanks big T

[@wcwickedclown]

is your kbat saving the settings ?

[@MrCpmboy]

Have you tried the soko kit?

[@jamesmorfison2008]

Can you use that on a 700 Chaos by aerodyne to level the Swash plate?

[@jackclemons420]

I've got a trex 550e on a hitec radio optic 6 sport. well I don't know much about this yet... I've not tried to fly it lol I know better. I got 1 ? though ... isn't the tail rotor supposed to center?? mine just stays where you put it. can this be changed in the settings?

[@wcwickedclown]

it should if the gyro i on active

[@elxero2189]

Hmm, No disrespect especially now that he's passed on. Just wanted to say I disagree with part of the method here. I've found nothing but headache by adjusting links to get level swash. It show's up later in the head setup when you try to get both blades tracking properly. Had best results with getting those links about equal as best I could. The elevator linkage may be a little shorter but as long as the ailerons are good I'm usually fine. So get those two exactly same length best you can and the elevator as close as you can. get those servos 90'ed using he same hole. Spend time on this step it makes the rest of your setup that much better. Just my 2 cents btw I'm no expert just an average noob, was planning to share my maiden with him then learned he passed 5 months ago. very sad now. RIP WC

[@tonyhodgson6744]

Hi WC, got your reply but it's not on these comments, bloody weird, yeah got skype but only forward facing camera, or we can just type.... Check out my last vid, the swash is ok. Think it might have been the ESC not initialising properly, it beeped 5 times instead of 3, also battery was low.....

[@TheBeastFPV]

I can't see the video bud

[@wcwickedclown]

if you have a mic ? whats your skype name ?

[@TheBeastFPV]

Wc my motor get a little hot what can that be

[@dmonkillr-rn4us]

are all swashplates the same?

[@wcwickedclown]

no they come in different sizes

[@tonyhodgson6744]

hey WC, good video bro.... i need to contact you regarding my vids too but i cant, you have made several comments which i value dearly but cant reply.... im hopeless with youtube man.....

[@wcwickedclown]

you have skype ? i see you need help and thats what ive always been here for brother

[@tonyhodgson6744]

Yeah got a mic, what's your skype name?

[@wcwickedclown]

wc_wickedclown1

[@JT-uf4pg]

do you have an email address

[@MrCpmboy]

Have you tried the soko kit?

[@wcwickedclown]

heard it works good but my normal gauges work fine and cost much less