Swing arm shaft spins. Pivot bolt stuck rubbermount sportster rear motor mounts

  Рет қаралды 19,989

504CharlieBoy504

504CharlieBoy504

Күн бұрын

Пікірлер: 13
@alissarobertson8840
@alissarobertson8840 4 жыл бұрын
What size is the right side swing arm nut. None of my sockets work
@nickflock5101
@nickflock5101 8 жыл бұрын
Same thing happened to my nightster. The rear swing arm pivot bolt is the worst design ever. Two little nubs on that retaining plate keep it from spinning. With the torque and vibration of the motor those little nubs are useless. They need to design something else. Let me know if you have found anything more heavy duty. I really wish they had a single bolt pivot shaft and maybe two retaining plates on each side of the motor mount. Cheers!
@obfuscated3090
@obfuscated3090 6 жыл бұрын
I haven't done a rubbermount yet, but could you install the tube and the plate at the same time? If so, I'd put three fat tack welds on the inboard side of the plate to permanently lock it to the tube. What the cheapass MoCo do for convenience is not always best for the owner!
@thakery5720
@thakery5720 4 жыл бұрын
I got no problem getting the bolts out - my spindle is seized in the crankcase !
@thevincentpaul
@thevincentpaul 2 жыл бұрын
I dont understand how you drilled a hole into the side of that shaft while it was in the motor. I also dont understand how that shaft gets stuck to where you cant get it out. Why not just hit it out with a hammer?
@ДядяМиша-т1я
@ДядяМиша-т1я 2 жыл бұрын
I also don't understand how this hole helped to remove the shaft. On my bike, it got stuck so much that a hammer does not help. I'll try the puncher.
@ryanbaldwin188
@ryanbaldwin188 8 жыл бұрын
The rubber mount you have already fitted in the video. How did you get the old one out? Did you have to in bolt the engine? This video saved me by the way thank you
@504CharlieBoy504
@504CharlieBoy504 8 жыл бұрын
I'm pretty sure I loosened all the motor mounts and stabilizer bolts, then used a block under motor and a pry bar. might have used a brass bar to knock it loose. what point of install are you at?
@ryanbaldwin188
@ryanbaldwin188 8 жыл бұрын
+504CharlieBoy504 I'm pretty much at the same point in this video but the old mount is still in place. I'm waiting on parts!
@reedr125
@reedr125 6 жыл бұрын
You dont show where on it you drilled! Do you have the old one? Did you hit the bolt?
@504CharlieBoy504
@504CharlieBoy504 8 жыл бұрын
unfortunately I found nothing better. had to go back with stock stuff
Replacing Rear Rubber Motor Mounts Harley Sportster 2004 and Up
11:36
Motorcycle Riding and Repair
Рет қаралды 16 М.
Penetrating Oil Showdown Episode 2. Will Seafoam Deep Creep prevail?
10:58
Smart Sigma Kid #funny #sigma
00:33
CRAZY GREAPA
Рет қаралды 19 МЛН
Lamborghini vs Smoke 😱
00:38
Topper Guild
Рет қаралды 22 МЛН
When Cucumbers Meet PVC Pipe The Results Are Wild! 🤭
00:44
Crafty Buddy
Рет қаралды 61 МЛН
Honda 400ex swingarm
6:13
Greg
Рет қаралды 37 М.
Sportster Swing Arm Removal 2004 and Up.
6:37
DIY Magpi
Рет қаралды 2,2 М.
How to remove a stuck dirtbike swingarm bolt
5:47
Novaguy383
Рет қаралды 1,2 М.
DIY Vibration Reduction in Sportsters - Rubber Motor Mount Replacement
47:00
Shovelhead starter RELAY replacement.
16:37
DW's Chop Shop
Рет қаралды 14 М.
Pressing Swingarm Bearings in 1985 Softail
21:44
Randy's retirement projects
Рет қаралды 534
Replacing Front Rubber Motor Mounts Harley Sportster 2004 and Up
10:22
Motorcycle Riding and Repair
Рет қаралды 14 М.
How to remove a seized swingarm pivot bolt
10:15
Trick Eng
Рет қаралды 35 М.
Smart Sigma Kid #funny #sigma
00:33
CRAZY GREAPA
Рет қаралды 19 МЛН