SolidWorks ʬ Tutorial

[@adrianhartanto7913]

make sure in linear pattern only 4 item to selected 1. Cut-Loft1 for the start 2. Cut-Loft2 3. Fillet1 4. Cut-Extrude4 for the end then in option click Geometry pattern

[@TitovIgorBro]

I have no idea what the fuck geometry pattern even means but god fucking bless you man, I've been fucking with SW for hours and the fucking pattern wouldn't fucking work

[@vasanthanand1319]

Thanks mate, that was helpful

[@ahsanmalik9576]

Thanks bro you saved the day. I was at the verge of getting collapsed ..

[@YuvrajSingh-oz2qc]

Unable to create contour geometry. Please check the loft section

[@PANDA-ev9dz]

God bless you ❤

[@Werkea]

For all the people whose LINEAR PATTERN does not work Make sure you are selecting the right procedure instead of just following the video Names can be different there should be only 5 that are selected. Two medium Holes cut at start loft 1 loft 2 Fillet two small holes cut in the end

[@weeabdull6915]

Thank you so much sir..that helped me out

[@vishnuvardhankadiyala8292]

Really thankyou Soooo much yarrr

[@TitovIgorBro]

THIS SHIT STILL WON'T FUCKING WORK GODDAMNIT

[@TitovIgorBro]

So ugh... you need the GEOMETRY PATTERN to be ticked for this to work in SW 2020

[@TitovIgorBro]

Nvm I'm a fucking idiot. You only need to turn geometry pattern on if you include the loft surface in the linear pattern

[@khalidashzz]

The fillet at the corners is 25.4 mm which matchs the engine block one👍🏻

[@pure9873]

Thanks man!

[@danielalonso5533]

Ty bro

[@capitaocavernadobras]

Parabéns. Ótimo Trabalho. Obrigado por compartilhar.

[@johnnywang8452]

the 2nd last linear pattern u do, don't forget the small extruded cut circle, u need to select 3 features for this step

[@Nargil55]

at 18:13 u're suggesting that this circle should have diameter 31,75 mm ? Couse in this case it is too big, circle sticks out from the form.

[@loginkid2]

+Nargil55 i have the same problem

[@ernstconradie9723]

+Mark C Hi Mark, I have the same problem as the guys above. THe extrusion cuts through my Loft Cuts, creating a gap. Not sure where we are making the mistake, but its bugging me no end!

[@ernstconradie9723]

Ok I just figure it out guys. We put our hole extrusions on the wrong side of the original extrusion (body) flip them over to the other side and we are good! (Im trying to figure out how to do that without having to redraw all the features I'm trying to flip)

[@lieutanhung748]

me too. i have the same problem. Have you finished?

[@Nargil55]

Just leave it sticking out, couse further in video he moves (dont remember what exactly) one of edges and it work just fine.

[@Supercross177]

Thanks for all mate, I'm learning a lot!

[@Sw-tcNet]

Supercross177 Thanks Supercross177 for your nice supercross comment, hope you enjoyed the learning here!!

[@christiandeleon]

Can someone please tell me how you get that texture look while you are modeling? When I change the appearance it only changes the color

[@pure9873]

Although I may be too late...... In you part tree there is a Materials branch. Double click and select a material.

[@kikobrito1]

Very good tutorial, I really learned a lot with this video!

[@tvaliulis]

fillet size is? last one ;/

[@MrBlackeagle2020]

Tadas Valiulis I was just doing the assembly. The fillet should be 25.4mm

[@brendacarrillo4490]

Thnks u :D

[@maazsiddiqui4872]

@@brendacarrillo4490 you are beautiful

[@yasinakcicek5169]

What was the last fillet size i cant finish the drawing please help me

[@gronbeck88]

25,4

[@yasinakcicek5169]

i finished the drawing its ok thanx for the reply

[@jonathanharkerdpz5906]

Excellent contribution . How much is it value Radius of fillet of the block (Cylinder Head.)

[@tvaliulis]

25.4

[@MrHeojun]

thank you dude

[@Interestingtgings]

this is really cool with all necessary details ,, thank you very much

[@alinassour2990]

why do u change the dimesions of the cylender head without saying itsnot fitting in both sides

[@MrRenoo94]

When I make the lofted cut, I can't select the circular edge for some reason. So, I had had to make a converted sketch for the circle to proceed. What could be the problem?

[@DerRumbringer]

what is the last fillet size ?

[@yyyoniii3245]

can i just ask where are you getting all those measurements, and thank you so much i cant wait to assemble all the parts

[@Sw-tcNet]

Jonathan Shirion Thanks Jonathan for your comment, The measurements are measured (many methods including the manual measurements & blue prints).

[@mezunmezun]

The only thing i really couldnt figure out is how we can produce this head including a way from valve hole to exhaust hole by using loft? Of course if it is made out of one part!

[@Sw-tcNet]

İbrahim Oğultay Good q., it is produced by "sand casting" , A molten 'grey cast iron' is poured into a previously made cylinder head from plastic foam placed in the sand which will be evaporated later & the iron will shape the place!

[@berkaycagl3161]

ufak bi döküm atölyesine git projeni ver yapsınlar :)

[@ricardoz5714]

SolidWorks Tutorial ☺ My grandmother used to be a wooden moldmaker who had engineered the wood model of the engine, and the models were sent to another factory where they were cast by sand casting into metal

[@sarajachob1227]

in hole wizard i didn't finde tools as yours ?? please help

[@qearetha]

Make sure your selections match all of his from top to bottom and then you find the bits your missing, as you select them other options appear. Also, right at the bottom of the click on the links(and deselect them).

[@craigkinghorn9705]

At 3 mins, why are increasing on side, and decreasing the other; would it not be easier to just move the valve seats in the pre sketch?

[@rubenprovencio-b1u]

Hola qué solidworks usas solidworks 3d CAD,3d experience solidworks O que versión usas Gracias Un saludo

[@lyesmokhebi9708]

I don't have the same sizes as yours in the bottoming tapped hole, I used the same standard as you did (ANSI Inch) but the sizes are different (the closest I found is 1/4-18 NPSM), I'd appreciate if you could help me, thanks in advance!

[@abhishekkamde2356]

ANSI INCH >Bottom tapered hole IS NOT IN THE LISTED HOLE WIZARD GIVE ME A SECONDARY IDEA OR HOW TO ADD OTHER HOLE WIZARD COMMANDS....i m using 2019 version PLZ RPY

[@SDCT]

i got some problem when i will apply the holes from hole wizards it will not appling on it why???? pls help

[@joseluisMartin]

Awesome job!!! a question, yuo've got all dimensions of the model?

[@powersterk]

You are the Best...

[@Sw-tcNet]

Hernando Jove Thanks Hernando Jove!

[@aviationavis]

Hello At Linear Pattern i have such a message "rebuild errors - unable to create contour geometry. Please check the loft section". I did with geometry and without it, but still not working, could you help me? cause am leading the tutorial, but i have such a kind of problem. I just want to solve it for knowledge. Thank you In Advance

[@Sw-tcNet]

Nikoloze Nikortsmindeli Well, it is not strange because the loft is kind of complicated to be patterned. So, quick choices I see now, try with the loft to be precise, or to be done again, or the1/3 block of head block with 2 lofts to be patterned as body.

[@shamithsatish4188]

@@Sw-tcNet im getting the same error and I am not able to resolve it.. Can you help with different solution?

[@vihargandhi9473]

can you provide materials for all parts ?

[@noorwehbe5849]

what is the material?

[@brantshank8121]

what is the last fillet size

[@lieutanhung748]

can you hepl me? Video has a problem at 18:10. I can't do it

[@brantshank8121]

diameter is 31.75mm

[@gavincone5446]

I'm a self taught high school student using this software and, (using this video as a guide) I built a DOHC head, cams, and custom sized valves from scratch.

[@qearetha]

Hey guys, when the linear pattern doesn't work, it's solidworks being a pain, sometimes you need to just leave it alone for a minute and it will work after. (I love solidworks but, it can be annoying).

[@premtephin1187]

14:38 I can not make it

[@av6966]

Wheres the water cooling jacket?

[@ulisemercado3192]

DO NOT PUT THE MEASURES OF LAST ROUND UP , THE CORNERS OF THE PART

[@SohilShah_Melodyman]

Gr8 tutorial!! Very helpful!

[@3goldy]

Why do you have to reCreate the fetures every single time? - Why can't you JUST duplicate them?

[@123kkambiz]

The same is my question. he could have copied them

[@simatmakina2963]

HEY. fRİENDS pART kORNNER. HOW MUCH RADUS?.

[@MysteryAccordeonMan]

This must be the worst tutorial ever.

[@garaazol818]

what is the last fillet size ?

[@guyfranklin8341]

25mm

[@MrRenoo94]

When I make the lofted cut, I can't select the circular edge for some reason. So, I had had to make a converted sketch for the circle to proceed. What could be the problem?