Plaese subscribe to 【DIY WoodWorking For Aug16】Channel on KZbin if you like my videos: / @ordinarydaily Turn on the little bell🔔 notification, the firs time to watch wonderful video~
Пікірлер: 14
@slibmir84123 күн бұрын
Привет мастер лайк однозначно! Все получилось точно и красиво! Я хотел бы узнать, уточнить радиус окружности вообщем размеры всех линий чтоб получить точный полумесяц наклонного механизма напиши пож если не трудно ? Спс удачи в труде
@sddiymakeitworthit7512 Жыл бұрын
Nice job 👍
@user-eo2xm6mt5n2 күн бұрын
Интересует сколько было неудачных вариантов прежде чем мы смогли видеть конечный результат на видео?)
@reaper060670 Жыл бұрын
Beautiful job there on the tilting and height adjustment my friend.. I am about to attempt my own build soon. The thing is I have most of it set up but I want to put a tilting mechanism on my saw with the 2nd wheel but I'm a little stumped by the whole thing. I will work it out but this video has given me a slight hint into a great way of building it into my saw. Thanks for that my friend.. Appreciate it very much. Keep up the great content..
@jamesmahon83811 ай бұрын
You do have to spend some time setting the saw up... blade, fence, etc. But once done, the saw is great. Fairly compact which is Nice kzbin.infoUgkxXh-4_3-ZT1fFWP91ZV7iVqzElr0lEb-a I did get an Incra Miter Gauge which takes some setup as well. The stock miter gauge can be adjusted in the miter slot with a little painter's tape... this tightens up the side to side play a lot.
@Иванов_ИИ10 ай бұрын
Гайки, которые заколачиваются (с шипами) - их не нужно фиксировать дополнительными саморезами. В них винты (ручка ч резьбой) закручиваются с ДРУГОЙ стороны доски!
@user-fh3nh1vd1c5 ай бұрын
Если по ручке ударить в торец ,то эта гайка вылетает !
@francisco-kb7mv11 ай бұрын
It is nice.
@wowyummyyy Жыл бұрын
LIKE👍👍 👍👍 👍😍 😍😍 😍🍀🍀🍀🍀
@makernova8160 Жыл бұрын
Great engineering! Can't wait to see more!
@reaper060670 Жыл бұрын
Hey there man.. I have a question if u have a moment to answer for me my bro. I'm about to begin my table saw build. I'm using old parts rom a cheap table saw so I have a bit of a head start but wht I cannot figure out is how u managed to get the blae to come up in the same position as u would for 90 degrees and 45 degrees. I would like to completely rebuild from scratch but that part I cannot get my head around. My table will be 1000mm (length) x 500mm (width). Is there a specific place I would need to place the whole saw mechanism to get it towork as well as u got it to work? What I mean to ask u is placement all important. I will be using some old parts from a cheap table saw with a 1500W motor. Hard start but I have the lift mechanism in there. What I want to put onto my new built saw is the tilt mechanism. So I guess my question is this.. Is where I place the tilt bar & mechanism more important to getting the blade to come out correctly as it does in the lift mechanism. I guess I'm asking daft questions here but I hope u get what I'm trying to ask u bro.. I haven't built a Table saw before so I would like to get it right. I'm using 40x40mm Sq tubing. I have some 25x25mm tubing too and some 50x25mm also. I bought the 40x40mm angle bar to build the fence aswell. I'm going all out bro but I don't want to mess it up. Any advice u could give me on the Lift & Tilt Mechanisms would be gratefully received by a fellow saw builder. At least I wanna say I'm going to do my best. Love the channel bro. Been sub'd for a good while. I shared the channel and video but I'm only getting back onto twitter now. I lost a load of ground there. I had a few thousands followers but they're all gone. I don't know what happened. I musta said something that wasn't liked. I can get a wee bit political sometimes and rub ppl up the wrong way. TGake it easy bro and keep up the awesome work.. I love ur table saw build..
@user-xf8rj4hg3w Жыл бұрын
امتياز
@ricardoaguiar224110 ай бұрын
The video is great but the music is very annoying.