Tamiya Mini 4WD - MK lll Avante (MA Chassis) Budget Bmax Build + Test Run

[@yuki-san20]

nc build sir ❤ other options pag tight budget front Mount plate x2 For underguard popsicles x2 rear X chassis break plate for side AR frp with 2sets of dampers 1 heavy damper Roller rear guide roller front Double aluminum rollers 12/13 😊

[@DEEMini4WDPH]

@@yuki-san20ohhhh thanks for the info. Yeah I could try that on my next MA build. 😊

[@seungjoon2037]

Pretty cool setup. I was wondering myself after several fma chassises replacements -the weakest spot on fma is side wings and rear motor shaft atea :(

[@DEEMini4WDPH]

@@seungjoon2037 yes yes, the side wings of fma is really weak especially if you crash really bad. But fma is one of the fastest cars in bmax category because it’s lightweight and motor placement. Thats the pros and cons of fma. :)

[@bennybouken]

hi I got question is it okay if I just use reinforcing plate for the front under guard?

[@DEEMini4WDPH]

Yes, I used that setup before (2 frp) for front under guard to serve as my brakes but I switched to rear brake plate to maximize my sponge power

[@VinoTagapan]

Hi sir good day may I ask if out of the box ganyan na po kulay ng unit nyo ganda po kasi, I’m planning to buy same color 😊 and also upgrade it. Saan nyo po nabili yung ganyan? Love the color combination. Thank you

[@DEEMini4WDPH]

@@VinoTagapan nku sir wala po out of the box na gantong kit hehe.. binuo ko lng sya so binili ko sila individually :) mostly sa lazada ni brickyard and tamiya undergound

[@VinoTagapan]

@@DEEMini4WDPHnoted on that sir thank you 😊

[@PinotNoir_]

can you do a brakeless dash motor build with this chassis on ? i hate using brake since sometime it wont stick properly and ended up stuck on the track somewhere. My super II Build use no brake but i'm struggling to build brakeless MA..

[@DEEMini4WDPH]

@@PinotNoir_ hi sir, i tried brakeless dash motor before but it doesn’t work, my car always crash because dual shaft is really fast. This is my tip for you so your brake sponge will stick on your frp plate 1. Cut and put double adhesive tape on your brake sponge before sticking it to your frp 2. Put some angle on your brake sponge by using a sandpaper (I used an acrylic 5R size then I stick the sandpaper 80grit) so I can angle the brakes Hope it helps :)

[@PinotNoir_]

@@DEEMini4WDPH ohh okay, thanks! i usually tape my brake plate with tamiya tape then just stick the brake sponge there. thanks for the tips!

[@DEEMini4WDPH]

@@PinotNoir_ you’re welcome :)

[@markmadolora143]

3mm white front sponge brake?

[@DEEMini4WDPH]

@@markmadolora143 2mm white/pink brakes front then 1mm white/pink rear. :)

[@ericconcepcion6952]

Where to buy silver dampers?

[@DEEMini4WDPH]

@@ericconcepcion6952 mostly at tamiya shops, available most of the time. You can check out lazada/shoppee account of Brickyard or Tamiya Underground

[@dredomingo9551]

what gear ratio sir for macdash motor?

[@DEEMini4WDPH]

Hi sir, i used 3.7 highspeed gear for the test run :)

[@morvicbayais8662]

hi sir pasok naman sa dimension box?

[@DEEMini4WDPH]

@@morvicbayais8662 yes sir fit sa dimension box

[@morvicbayais8662]

@DEEMini4WDPH thanks sir sa reply

[@ricardo.pedrigosa]

good day boss. para san po ulet yun super x chassis na frp?

[@DEEMini4WDPH]

@@ricardo.pedrigosa sa likod sir “anti -sabit” para if di maganda ung bagsak ng oto mo from a jump magsslide lng sya pabalik ng track and hindi sasabit ko masstuck sa edge ng track

[@ricardo.pedrigosa]

salamat sir! more power sa channel

[@aprilgarcia1121]

sir ano po size ng bearing inilagay sa may wheels?

[@DEEMini4WDPH]

@@aprilgarcia1121 hi po. I’m not sure about sa exact size pero eto yung gamit ko. Round hole ball bearing item number 15-111

[@MITZ-cx4je]

Pwede pa e push 👍

[@DEEMini4WDPH]

@@MITZ-cx4je yeah hehe :) need to breakin another new mach dash motor. The one im using is just giving me 28k rpm. I can see other racers they can go up to 30krpm

[@xHANIELx]

pwede po yun cowl na ganyan sa chassis ng neo falcon red?

[@DEEMini4WDPH]

@@xHANIELx yes sir. Same chassis naman sila kaya fit parin

[@xHANIELx]

@@DEEMini4WDPH salamat po sir.. ipon muna dun ako pangsetup hehe

[@DEEMini4WDPH]

@@xHANIELx you’re welcome sir. Yes dont rush onti onti lng sa pag build :)

[@OzzoBear018]

sir mag kano inabot lahat ng set up na to?

[@DEEMini4WDPH]

@@OzzoBear018 hi sir around 2-3k estimate :)

[@OzzoBear018]

@@DEEMini4WDPH maraming salamat sir. more content po pra sa mga newbie katulad ko. god bless!

[@DEEMini4WDPH]

@@OzzoBear018 thank you din sir. If meron kyo question message nyo lang ako sa fb (DEE Mini 4WD Ph). I’ll try my best to answer your questions

[@DEEMini4WDPH]

@@OzzoBear018you’re welcome sir. If you have questions you can message me at facebook (DEE Mini 4WD ph). I’ll try my best to answer your questions