Adjustable Voltage Regulator 0-36V 10A

#adjustablepowersupply #voltageregulator #dcdcconverterupgrade

[@christopherwilliamdodd236]

The output from the DC to DC regulator will always be voltage regulated. The output from the transistor is not regulated. You will need to modify the DC to DC converter so its feedback loop is taken from the emitter of the 2N3055 if you want a voltage regulated output.

[@JoaoFerreira-gp5qx]

very nice we always want 13.8v but drop´s

[@MandauTerbang1945]

Ide yang bagus

[@RixtronixLAB]

Nice video, well done, thank you for sharing it :)

[@senolbalkan9246]

Harmonic Distortion yönünden Temiz bir dc akım veriyor mudur Osiloskop ile dc nin ne kadar temiz bir dc kaynağı olduğunu göstermelisiniz

[@Zeeshan_Ali32]

As you have shown the voltages, you should also show the amperes as well.

[@SAM555KZ]

2-3A at maximum

[@saddikuabdulrahim2857]

Excellent job I love it

[@nanisai7321]

Sir it perfect for long run.

[@harunresitkaya2836]

Tek 2n3055 calisiyor fakat 2,3,4, tane 2n3055 takinca sadece bir tane tramsistor calisiyor fazla akim cekince o calisan transistor kisa devreye dusuyor

[@carnero1970]

Muy buen circuito,pero hay un problema ,el darle los 40 V. De entrada sería un problema ya que si no recibe esos 40 V. No dará los 10 amperes de salida y para alimentar 40 V. es algo difícil

[@shahidchef490]

moudule kitnay ampare out ker rah hai 100 ya 200 milamp out kerana chaiye transsitor kitnay amp out ker ra hai ye to check hi ia kitna heat ho ra ye sara kuch ager fix 78013 laga ker out chiye to wo kais ahia

[@arajasujathaars6894]

Thank u for giving new idea🎉sir ihave one doughtwhat was the ampere stands..thank ..u iam ur subscriber💐🙏

[@TARIQLAB]

Explain ?

[@hobielektro]

Mantap

[@jahangirshaukat1725]

Please make boost converter xl6009 with transistor 3055

[@mehmetyildiz7402]

❤

[@jahangirshaukat1725]

Same work with booster Module Please make a project with xl6009 same work 2596 Module.

[@abdulqayyum4597]

Will this increase buck converter ampere from 3A to 10A? Withiut any problem?

[@isabella5790]

The buck converter is protected vía the 22 ohm resistance. Here the negative pole would need extra beefing though, for those high amp needs, since the printed circuit of the buck converter obviously is not ready for such high amp levels.

[@TARIQLAB]

Not through buck converter but direct from the source, i use buck just for regulations purpose

[@oturanboga6225]

süper

[@ariefbudiardjo7320]

If a replece the NPN Transistor (3055) with PNP (2955) cant it work as it? how we connnect the pin ?....are the same?

[@TARIQLAB]

Converter output is positive so only NPN transistor can be used, because positive current required to trigger NPN transistor

[@ariefbudiardjo7320]

@@TARIQLAB thx for your answer. 👍👍👍👍👍

[@MoisesPinto-17]

Where the output ampere?

[@shahidchef490]

500 ohm sekam kiresistanc e laga ni chaie kam sekam 100 ohm half wa ki b chaly gi

[@SpaceSoftSystem]

I want it for DC BLDC motor and electrical scooter controller testing , DC 48v to 72v or 48v to 60v

[@shahidchef490]

npn hai to negitive suply pas out ki bjaye positive out ker 3055 how todo work

[@TARIQLAB]

Positive hi collector pe di hai

[@shahidchef490]

@@TARIQLAB ok

[@pekjinoei1042]

How about add a 5K VR at B point so that the voltage can be adjust as we need... I also want to add something to make the current adjustable... And at the end point, I want to add a shot circuit protection module...

[@SAM555KZ]

*do not do that! you shall brake base of 2N3055, moron!*

[@robinhutnc2392]

How to make a variable voltage variable frequency AC power supply. 0-380 volt, 0-1000Hz.

[@SAM555KZ]

*Resistor should be 56 Ohms*

[@robertneill3057]

Try with an Arcol Metal clad resistor 300W of 4.7 ohms.

[@isabella5790]

On and on, we could keep on exchanging lower resistors with higher wattage for a while for higher output to a limit.

[@manz495]

Weldon demo