How To Replace Thermadore / Bosch Dishwasher Door Spring Cable 00754866 | Easy DIY

[@BillFloria]

We tried hooking the the plastic piece first, weaving it around and then stretched the spring coil and slotted it in. Worked for us

[@williamferraro369]

Yes this is the way to do it you can do it without tools by hand this way.

[@halarnarson]

Thanks for sharing! I was able to easily do this repair on my Bosch dishwasher in about 30 or so minutes. It was even easier than the video because there were no metal plates to remove on the sides of the dishwasher

[@Tech4Baba]

Good to hear! Thanks for watching and sharing, @halarnarson! Yeah, Bosch dishwasher is even easier without the metal covers on the sides.

[@peggyelliott4391]

Thank you so much for this great video! You convinced me that I could fix the door myself, and even gave me the link to order the springs. The whole job took me - a 70-year-old woman - less than 15 minutes and saved me $$$. The best!!!

[@kattle32]

Great video, this is exactly what failed in my dishwasher 2 weeks ago and after reviewing the replacement kit, it's all fixed!

[@timbyassee9890]

You asked for suggestions on how to install more-easily. I found that if you feed the cord over one pulley only before attaching to the hinge, it goes-on very easily. Then, pull the cord over the other pulley either with your hand or using a needle-nose plier. Much easier than maintaining full-tension on the spring while trying to attach to the hinge

[@MilouTintin]

I notice that the old springs have two widths, and thus two levels of resistance. This allows the door to open more easily at first, and to hold the door more firmly as it pivots down. One week later: the parts arrived, and it took me TEN minutes to replace the old springs on my Bosch. I didn't need to disconnect the electrical or the plumbing: there was enough slack to allow me to pull out the dishwasher. Getting the old springs out required a bit of levering with a screwdriver, otherwise, smooth as butter! Thanks, Tech4Baba! I'm leaving you a tip to thank you for all the money you just saved me!

[@febsat]

Excellent step by step. I have a Kenmore Elite model series 630.xxxxx. Sold by the now non-existent Sears Canada. Impossible to get any information on this model. It is made by Bosch. I only know about the Bosch connection, as I was advised of this relationship directly by Bosch during the issuance of a technical safety bulletin several years ago. I wrote to Bosch, and they confirmed that the Kenmore 630.xxxx series was in fact produced by them. They stated that this was the only Kenmore model produced by Bosch. The rest were made by Whirlpool and Frigidaire. It is also the only Kenmore model with side panels, which of course need removal to access the springs. You covered all the bases and made this a quick simple fix. Thanks for posting.

[@BK3HB]

I used a #0 Phillips screwdriver shaft in the installer hole in the plastic clip for leverage to pull the clip over the door hook. Great video. Thanks,

[@rbcrain2469]

Thank you! We purchased the improved spring with the metal connectors. It was hard to get the old broken spring out, but we managed. We used vice grips to pull the string and the spring apart to connect the string side to the door. The new replacements are working great so far! Many Thanks for posting this video.😊

[@Tech4Baba]

Great to hear! Thanks for sharing and letting me know, @rbcrain2469!

[@smithvalleyjim]

Just received the parts via Amazon in two days! Used this video to guide me and it was perfect! My model had no side panels so that made it even easier. Thanks!

[@yuvaltirosh]

Great video, I was looking to see whether the broken plastic ends were essential before ordering a new kit and glad to see the metal ones replace them, cheers!

[@JamesGarvey1]

Insert a flat headed screwdriver between the spring coils. This will spread the spring out and will give you more leverage to push the spring toward the door, so it's easier to connect the plastic hook at the end of the spring to the door

[@mkrempasky]

This was enormously helpful; clear and easy.

[@polsilverok]

hi, Thank You Very Much , this instruction can not be any easier , did myself and saved money , cheers from UK

[@Tech4Baba]

Glad to hear from UK! Thanks for watching and letting me know, @norbertkorcyl3244!

[@MilouTintin]

Thanks!

[@donnysworld6774]

Outstanding help video !!!!!!!!!!

[@dwaski1]

Great video! Simple and straightforward! Also, thanks for the links to the improved spring kits :)

[@utubota5522]

Thanks, this saved me from calling an appliance repairman.

[@Tech4Baba]

Great to hear! Thanks for watching and letting me know, @utubota5522!

[@toddmontazzoli2461]

This video and replacement part was perfect. Thank you!

[@davidure67]

Thank you! Just did the repair.

[@denniskeener8708]

Thanks for the video. Very helpful

[@Tech4Baba]

Thanks for letting me know, @denniskeener8708! Were you able to fix your dishwasher?

[@Mikego55]

Great video.

[@JohnScott-k9t]

I could not get enuf leverage to stretch the spring so I used a Pony tape clamp. I put a simple slip knot loop in the tape and ran a loop of strong wire through the plastic clip that attaches to the door. 6:25 There is a hole in it that us probably used by an installer. There is a steel stud on top the frame that I anchored the rachet on. I got it lined up with the hook on the door and released the rachet. There was a satisfying thunk and I went to the next one. Masking tspe to hold the spring in place

[@OliverMcIrwin]

My screws for side panels were torx 20. Also it was only the bottom one on each side. I had to bend back the black plastic flaps to find them

[@ericlin8712]

My model could be like yours but I can’t bend back the black plastic flaps. Could you elaborate more how you bend the plastic flaps and find the screws? Thank you.

[@steveevanchik6408]

I used the second link for the new springs and installed as instructed in the video (very helpful). The tension to keep the door up with the new springs installed is a little better but the door still crashes down at about 1/4 of the way open. I have the exact dishwasher as in the video. Has anyone run into this issue? Is there any way to make it more tight?

[@guapististio]

Thank you!!

[@Jimalooch]

Great video! Looking for replacement door spring kit for DWHD440MFM/02 but having some trouble - can’t seem to line up model number with any available replacements on Amazon. Please help!

[@PeterDennis-u2y]

superb - thanks to sharing this.

[@Tech4Baba]

Thanks for watching, @user-vn9kh2sd8k! is your dishwasher having the same issue?

[@tc7486]

Will this work on a 9 year old Bosch dishwasher? And does the replacement part need to be specific to the model number Bosch?

[@Tech4Baba]

Good question, @tc7486! My Thermadore is about 8 years old. I think they share the same replacement parts but you can double check for your model number on amzn.to/3OzxYeK.

[@MilouTintin]

Your dishwasher part number is on a sticker inside. Mine was on the righthand inside lip of the door. The replacement kits usually list the compatible models. Mine was a SHP65T55UC/02

[@ishmcgee]

Well done. Thank you.

[@ChemicalArts]

I went through this exact process about 2 years ago with the new "improved" spring kits. The metal parts didn't fail, but the plastic part that hooks onto the door failed in than two year period. I'm starting to think that Bosch designed these parts to fail.

[@pamelaminthornjoneja9379]

Has anyone had an issue with the new kit being a little too long? It hardly required any stretching of the string to install, and it barely decreases the speed at which the door falls open. I bought a kid that claims to be OEM Bosch and correct for my dishwasher. I'm thinking I could knot it at the end near the spring to shorten. Any other ideas?

[@jlsajfs8089]

I'm struggling to remove the old springs. Has anyone had luck removing them?

[@MilouTintin]

I used a screwdriver to lever them out from the back. But you've probably already resolved the issue by now....

[@pamelaminthornjoneja9379]

@@MilouTintin I did that too. It took a lot of wiggling but eventually came out.

[@truongngochan7570]

Hey. How much???

[@notAdamDriver]

Close the dishwasher so you don’t need to stretch the spring

[@Tech4Baba]

Good point. Thanks for watching and the tip, @notAdamDriver!

[@Fabricetdf]

Thanks!