Teco L510s VFD, local control, commissioning, parameter set up, Factory reset. ( English )

[@dherman0001]

I see guys complaining they can't hear you. I'm from the United States, I can clearly hear you, with a moderate Eastern European accent. Clearly English is his 2nd language, but i had zero issues understanding.

[@ONYAMate]

Well this got me out of strife today. Thanks for putting it together and uploading it. Cheers.

[@IGSElectronics]

Hi there. Am glad it helped you out. That's way these videos are for.

[@slickstick6687]

I am building a big workshop air scrubber and I would like to thank you for your input on this inverter

[@IGSElectronics]

Your wary welcome. Am glad it helped you out.

[@baseemabusalah6131]

Really thank you for this beautiful and clear explanation

[@munshyakabamba4861]

Thanks your video saved my job❤👍

[@bikefarmtaiwan1800]

thanks for a good video~ please make sure you speak as clearly as you can because it is often hard to catch what you say . Thanks again

[@tomgould6734]

Thankyou I couldn’t have got this working without this guide, you are awesome

[@IGSElectronics]

You're very welcome!

[@IvanMushi-u3s]

Well and thanks again..,but I've a question please! what can i do if my TECO e310 vfd is showing LU on digital screen and REV signal on remote controller pad??

[@prabhassantra7115]

Which is best Switching frequency / carrier frequency settings for a motor provide by drive ?

[@Robbertdelange]

Just connect him to your computer and life will become so much easier

[@dherman0001]

I've got a 50 hp f510 teco. Under motor parameters rated current, I can't get it to go above 9.2 amps, which coincidentally is the max amp rating for the 5hp 510. Is there a hidden menu to access the max motor rated current? Makes sense it's hidden or hard coded so folks don't fry the drives. Any advice?

[@IGSElectronics]

Some drives do allowed it some don't. To be hones, i don't know way they would, that would eventually damage the drive. I have never tried to go above it for this drive so wont be much help for you here. Sorry

[@dherman0001]

@@IGSElectronics I figured it out. There's another menu level that's not published. Fixed

[@charlesbradshaw1285]

The documentation thatcomes wit the RS version is confusing/wrong. Your video helped me to get the beast working. Is it possible to display the motor RPM? Is so a vid would be great.

[@onjofilms]

Set parameter 12-04 to '1'

[@letsfixit1594]

Brilliant thx brother!

[@IGSElectronics]

My pleasure!

[@MrMichael361]

Can you please do one on the TECO E510s please

[@tareqjpour9373]

When I upload to the device it is encoded with cl what is the problem

[@bradyb9138]

Do you know a way to change the frequency adjustment increment? I have E510's with no potentiometer, so I have to sit there and mash the up/down arrows for a long time to get from 0hz to 60hz (US)

[@IGSElectronics]

I have never done it on this drives, but some have option to increase the sensitivity. Usually by increasing acceleration time should allow you to increase speed faster.

[@tareqjpour9373]

When I upload to the device, it is symbolized by a letter CL

[@maximilianomorin5951]

Mate, put some tape around the shaft to hold the shaft key. You will loose an eye or your camera. Safety first!!

[@bluesapient3447]

Can I run a 3 phase motor with it by supplying single phase electricity?

[@IGSElectronics]

Yes that is correct

[@bluesapient3447]

Can I run 2800rpm 3 phase motor at very low RPM with this?

[@louiealberigo5151]

My question is trying to program for piece per minute. Where to program frequency to say 120 pieces (displayed) with frequency at (guess) 48.7 htz?

[@louiealberigo5151]

On an E510

[@IGSElectronics]

@@louiealberigo5151 you will need the plc or some external smart relay for it.

[@erginkoc9554]

What does the driver mean by giving the CF-08 code?

[@IGSElectronics]

as far as I know this code is for different teco drive, that I have not worked on yet. Sorry wont be much help here.

[@lamngeunkeomany7157]

Please hell me about Parameters Teco t310 4008-H3

[@leomunoz4939]

You mumble too much bro

[@IGSElectronics]

Thank you.

[@65jcbc]

Terrible, in a hurry andI can’t understand what he is saying most of the time.