5hp 6hp 6.5hp Power Sports This is a Tecumseh Powersports carb with no choke but it does have a primer bulb
Пікірлер: 87
@bensk853 жыл бұрын
Thanks for this video dude, very concise and detailed. Helped me out with cleaning my carb. I went thorough the whole process just to find out that my problem was the spring controlling the idle. It was loose, so I just used a paperclip to tighten it up
@sixtyfiveford14 жыл бұрын
@eskimosrpimp619 ..............You can check the air filter by running the engine for a minute without it and see if it makes a difference. I have had semi clean looking filters cause serious engine running problems(but its rare). Spark plug is always a good thing to check. If the gasoline is older than 2 months that could also cause a little rough running. As far as starting: the primer button my be dried up and you may need to pump it 5-10 times to get a 1 pull start.
@sixtyfiveford12 жыл бұрын
Thanks. I like to cut open oil filters after I use them and realized they make excellent cans.
@sixtyfiveford14 жыл бұрын
@atoxx1 .........Yes it can. If it's leaking because the float is stuck open then you are flooding the engine.
@sixtyfiveford14 жыл бұрын
@35buck ....Your idle circuit is clogged. The idle jet is on the side of the carb. Make sure it is cleaned out especially the pin hole in the tip. Also there is an idle passage on the Main Jet bolt that holds the bowl on the carb. It is also a pin hole, located at the top of the threads.
@balabay7711 жыл бұрын
'Dances with wolves' and 'wounded knee' explained to the tribe that Shaman Tecumseh likes to expose his rod. He's been doing it for years. Chief stood up, took a hit of smoke pipe and passed it on to the rest of the counsel. "Prepare a noble death song for the day when you go over the great divide. Sing your death song and die like a hero going home" said chief Tecumseh to a governor as he threw a rod. Indeed, it was a sad day when Tecumseh wouldn't turn over on a third pull.
@sixtyfiveford14 жыл бұрын
@atoxx1 .......... to drain the fuel out of the bowl. Yes they can be swapped.
@35buck14 жыл бұрын
I have the same carb. you are rebuilding. I took it apart cleaned it out with carb cleaner and replaced the o rings on the emulsion tube and the needle and seat. The primer ball is weathered but works to start the engine. The problem is that I have to hold the primer ball in to keep it running or I can tighten the idle screw both of which makes the engine run at a high RPM. The engine is on a go cart so I need it to idle down. Thanks ahead of time for any help
@sixtyfiveford14 жыл бұрын
@eskimosrpimp619 .............. stick a phillips screwdriver in the fuel line when you pull it off to stop the gas flow. Yep sounds like you need a card cleaning.
@w9tched21510 ай бұрын
Could you make a video showing how to put an aftermarket exhaust on the tecumseh
@mariecorona098 жыл бұрын
ok I will do that thank you so much for your help.. I will keep you posted. ;)
@Cody-ye3ye5 жыл бұрын
I bought a brand new carburetor and it starts and revs up but then dies after 2-3 seconds. Any tips, it has good compression and good, I did add fuel filter but that shouldn’t restrict it too much right?
@charlesroberts64903 жыл бұрын
I have two of those motors but mine don’t have primer bulbs they have chokes I think the primer is better
@carlostrujillo50682 жыл бұрын
I hope you see this but I have a carb I need to replace on the same motor but 6.5 hp what carb do I need if you know
@samvanandel344210 жыл бұрын
***** at a gas station right around the corner from me they have 91 octane non-ethanol gas. Runs super good in ALL small engines.
@samvanandel344210 жыл бұрын
sixtyfiveford they only have 91 octane. It usually costs around 40-50 cents more per gallon, but it is totally worth it. We use it in my go kart, lawn mowers, snowblowers...
@pauldebusk4856 жыл бұрын
Hey I have a yerfdog spiderbox it’s a gy6 I believe and it’s not starting it sounds like it does before the idle
@sixtyfiveford13 жыл бұрын
@forgottenblack Sorry but I don't have this engine on hand.
@candylips36844 жыл бұрын
Hello i like to ask why my gokart is hard to start, an why it do start i drive it, an everytime i slow down or stop it turn off, and i have to wait about 30 min before it start up, by the way im a new subbie🖐
@sellerjax5 жыл бұрын
Thanks for the video. I just bought one of these and cannot figure out where the oil drain plug is on these. Could you please point me in the right direction?
@sixtyfiveford5 жыл бұрын
On the squared base of the engine there will be a drain hole in both sides(under carb and opposite). It will either be a square head bolt or an internal allen. At 0:09 to 0.11 it's dead center in the video screen.
@sellerjax5 жыл бұрын
sixtyfiveford it was an internal Allen. Thanks again. Appreciate it
@nighthawkj30A44 жыл бұрын
My Red 1998 Manco Terminator gokart has the same set up great gokart and engine. Is this one A Critter or Terminator Manco Gokart?
@sixtyfiveford4 жыл бұрын
Manco made a great gokart.
@nighthawkj30A44 жыл бұрын
sixtyfiveford yes they did 👍 to bad they can’t bring then back for a bit. But i guess it was only a 80’s 90’s thing.
@mariecorona098 жыл бұрын
Im the mom of to boys and Im determined to fix theit lil go cart...it has the same motor. the 6.0 tecumseh power sport
@johnfisherman87327 жыл бұрын
Can you tell me how to remove the carb? That's the part I needed to see but that was skipped
@sixtyfiveford7 жыл бұрын
Remove the air filter/air filter housing and it's retaining bolts Remove the fuel line Remove the 2 bolts holding the carb onto the intake Slide it off while allowing the throttle linkage to stay on the engine.
@Shoalie4 жыл бұрын
Can be linkage on the plate be purchased?
@PureRetics10 жыл бұрын
I have an important Question if you can help me. I have the same engine except mine is the 6.5HP powersport model. I need to order a new carb but i can not find a carb that matches my model marked on motor. Mine says OHH65 spec number 717136 every carb I look at online starts out with H63 or 64 as first 2 numbers on carb model. I can not find any replacement carbs that say OHH65 replacement. Is there a number I'm overlooking or missing? I'd like to be able to order 1 as soon ad possible to get my sons Carter gocart back running. If you cld help I would really appreciate your time. Thanks!
@sixtyfiveford10 жыл бұрын
PureRetics Your engine should be a OHH65-71713c or 71713d. If it's a 71713c your carb is part # 640025C. If your engine number is 71713d your carb part # is 640305. The ethanol in fuel is playing havok with these small engines and even with a new carb you will be back in the same position in a year. You can try the quick clean method. It only takes 5 minutes and works most of the time kzbin.info/www/bejne/gYrNZqJ-ZduBjMk
@MrChancelol6 жыл бұрын
Hey! Where is the idle screw on these engines? Mine won't stay running unless I give it gas. I tightened/loosened (wasnt sure what way) the little nut on the throttle cable and it works but now the go kart moves without me giving it gas which is annoying
@sixtyfiveford6 жыл бұрын
The idle speed screw is on the very top the carburetor. Look right above the primer bulb. It may be a torx screw.
@hpmower12 жыл бұрын
nice oil filter cans
@charlesroberts64903 жыл бұрын
Take pictures too
@dopVerse7 жыл бұрын
I have the same motor as this and the motor keeps coughing. I'm pretty sure the carb is out of adjustment. How do I adjust the carb?
@sixtyfiveford7 жыл бұрын
You can't adjust them. You need to clean it.
@tilicobarragan18998 жыл бұрын
Hi,I got the same engine I put it on minibike the only thing it's missing it's the shaft bolt the one the holds the clutch. You know what size it is please. Thankyou
@sixtyfiveford8 жыл бұрын
+Francisco Barragan Generally it's a fine thread Grade 8 or 9, 5/16"
@tilicobarragan18998 жыл бұрын
+sixtyfiveford thankyou
@devinbarton32107 жыл бұрын
Francisco Barragan 5/16ths
@mariecorona098 жыл бұрын
can you please show me how to rebuild the motor
@jimmymacias25836 жыл бұрын
What kind of oil can I put in that motor. Want to do an oil change but have limited knowledge on these small engine.?
@sixtyfiveford6 жыл бұрын
SAE 30W is the best for these guys.
@jimmymacias25836 жыл бұрын
Awwsome thanks just picked up a small can with 1.5 quarts. Should that be enough for oil change. Also We're does this motor come from. Like what machine.??
@sixtyfiveford6 жыл бұрын
These motors were used on a lot of equipment. Go Karts were one of the more popular uses.
@JulianLopez-se9sd5 жыл бұрын
CAN YOU HELP ME FIND THE BELT FOR THAT SAME GO KART
@sixtyfiveford5 жыл бұрын
Google it and you'll find your belt.
@ethanhill34688 жыл бұрын
Do you know a website that I can find a new replacement filter for my Yerf Dog 3203 on?
@sixtyfiveford8 жыл бұрын
+ethan hill Look up your engine not the Yerf dog. There are literally thousands of websites that will sell you an air filter including Ebay and Amazon.
@plattycakej35095 жыл бұрын
But how did you get it off homie
@jimmyprice15336 жыл бұрын
When start engine it runs full throttle what causes this
@sixtyfiveford6 жыл бұрын
Main carburetor butterfly is sticking open. Move the little lever on the top/towards back of carb back and forth to free it up.
@paulevans52269 жыл бұрын
I got same engine on my Murray Go kart any tips to make it faster cheers
@sixtyfiveford9 жыл бұрын
Paul Evans Changing the gears or adding larger rear tires will give it higher overall speed. This will make it more sluggish to start though.
@paulevans52269 жыл бұрын
I was thinking of taking the covner out
@sixtyfiveford9 жыл бұрын
Acceleration is where you feel power and doing this won't make any difference in acceleration. The governor simply keeps the engine from over revving(red lining) but also helps it idle and not die while your sitting. You can adjust the governor to allow a higher engine rpm but you will only gain a miniscule amount of rpm/speed. If you go even slightly to high with engine rpm the motor will blow up and then you won't go anywhere. It is equivalent to an RPM limiter on a Race Car. These engines are rated to run at 3600rpm and are generally set to run at 3400-3600rpm to make it last a good long time. You can push it to 4000rpm by adjusting the governor but no higher. This will give you an extra 2mph faster top end speed (virtually unnoticeable).
@paulevans52269 жыл бұрын
Ok cheers for that I'll probably put bigger tyres on the back then
@braedendaniel12039 жыл бұрын
Show us how to clean a 4 wheeler carb
@sixtyfiveford9 жыл бұрын
Braeden daniel They are all very similar: Polaris- kzbin.info/www/bejne/eKXHk52mi9F8bas Yamaha- kzbin.info/www/bejne/nWakoGmNnrZqsK8
@kevinvenegas18076 жыл бұрын
How do I fix it
@mariecorona098 жыл бұрын
The motor locked up I wasn't sure if I had to use mix gas or not...
@sixtyfiveford8 жыл бұрын
+Borry Corona It takes regular gas. If the motor is seized it will be less work and probably the same amount of money to use a brand new engine. If you have a Harbor Freight Tools nearby a new engine (6.5hp 212cc) can be bought for around 100bucks. It will bolt right up and use the same pulley on the current motor. The only thing you'll need to configure is hooking up the throttle cable, which shouldn't take much effort.
@isaaccampos55845 жыл бұрын
What spray is that?
@sixtyfiveford5 жыл бұрын
Carburetor Cleaner.
@ricardovazquez80487 жыл бұрын
GOOD AFTER NOON I HAVE THE SAME GO KART AS YOU AND I AM HAVING TROUBLE FINDING THE WHELL BEARING THAT GOES IN THE LEFT REAR WHEEL BUT ON THE INSIDE PART THE ONE THAT GOES ON THE AXLE CAB YOU SEND ME YOUR EMAIL SO I CAN EMAIL YOU SOME PICTURES OF WHAT IAM TALIKG ABOUT .THANKS FOR THE HELP
@sixtyfiveford7 жыл бұрын
Bearings all have numbers written on them. Pull the bearing off the other side and look up the numbers.
@ricardovazquez46387 жыл бұрын
RICARDO VAZQUEZ Good morning I did check the other bearing dans ordered the 499502H but when you take of the wheel there is an extra piece that's over the axle that doesn't go trough the hole of the bearing the inside diameter is 5/8 but I want to email you some pictures i really need help
@sixtyfiveford7 жыл бұрын
The 99502H is a very common bearing. Look at a parts diagram to get a better idea of all the parts that are going into the assembly. www.bmikarts.com/yerf-dog_ep_44-1.html
@dannys697 жыл бұрын
could wd-40 be used instead of card cleaner
@sixtyfiveford7 жыл бұрын
Sorry no. The carb cleaner dissolves all the old gasoline and clears that passages. WD-40 wont.
@dannys697 жыл бұрын
sixtyfiveford ok thanks also do would i have to drain the gas out first or it doesent matter
@sixtyfiveford7 жыл бұрын
FouseyTube Tube I would drain the gas to make sure there is no water in it.
@jasonsoto66238 жыл бұрын
whts the needle at 5:03 for?
@jasonsoto66238 жыл бұрын
When I was cleaning my carburator I found it on the floor and I didn't know where it came from so I didn't put it back in.My carb got overflowed with gas and started leaking it and the kart wouldn't run and wouldn't idle. Was the needle the cause of all this?
@sixtyfiveford8 жыл бұрын
The needle keep the gas at the proper level in the float bowl. Gas will run everywhere without it.
@jasonsoto66238 жыл бұрын
+sixtyfiveford thank you but i decided to just get a predator
@kevinvenegas18076 жыл бұрын
Hey mind is like dropping gas so much
@sixtyfiveford6 жыл бұрын
Your float is sticking or the needle seat is bad. You need to pull apart the carb and rebuild it.
@xtremeprosnipez10 жыл бұрын
Mine slows down when it bounces it sucks
@sixtyfiveford10 жыл бұрын
xtremeprosnipez That's odd. It could be the kill switch grounding out.
@Louisianagames10 жыл бұрын
Could also be the pick up in the gas tank stopped up. When the gas sloshes around could put air in the line.