Tello Motor Repair / Replacement

How to replace a DJI / Ryze Tello motor
Here I fix a Tello with a broken front motor. The goal was a clean repair job with minimal damage to the drone. It took somewhat longer than in the video. A bit over an hour should be ok for the fix.
See the list of materials below.
Motor (set of two): www.banggood.com/2Pcs-8520-8_...
TS80 Soldering Iron: www.banggood.com/MINI-TS80-Di...
Iron stand: www.banggood.com/MINI-T-stand...
Wowstick: www.banggood.com/Wowstick-1P+...
Spudgers: www.banggood.com/6pcs-U-niver...
Some more details in my blog: www.areresearch.net/2020/05/t...

[@pgScorpio]

To avoid the fidling with the motor wires there is a simple trick: Before removing the motor solder it's 2 wires together to a thin peace of wire. when removing the motor you will pull the attached wire through the hole. now desolder the wires and solder both wires of the new motor to it. than use the attached wire to pull the motor wires back through the hole.

[@WoutB848]

Thanks for the great video, my son was in tears when his Tello broke! Thanks to your video and tools specifications we just fixed it! Brilliant thanks from my happy son!

[@iandaly8786]

Thanks for the excellent video, I feel that I know everything I need to know to replace my non-working motor. Also there are some good suggestions from your followers to make the job even easier, which if you hadn't made this video I would never know, so a double thank you!!!

[@yury3647]

Thanks for the great video! Love the way you are trying to make it look "not bad". Perfect work. And very interesting how the man with a speedmaster on his wrist is fixing a toy for 100$😁

[@PhantomTD]

The best Tello repair guide I have found, no shortcuts taken. Also, nice watch!

[@antt1674]

Nice job! Thanks for the inspiration to repair my Tello. Going to give it a go today. Wish me luck!

[@AReResearch]

How did it go? Have you fixed your Tello?

[@user-2uf2kr2c]

Hi, i think there's an easier way to this. Just cut the wires at different length (so you don't have the solder-joints right next to each other) somewhere in the middle of the legs, cut the new wires correspondingly and solder them there. No need to open up the bottomcover and risk damaging something on the mainboard. Regards

[@ademjohannessen4472]

hi, the problem with my drone is that I pulled the drone propellers and the motor went out and the wire broke. Can I solder the wire together? or does it not work

[@AReResearch]

There is a Video on KZbin: „how to repair mini coreless motor“. That might be worth a try if you’re on a tight budget. But I‘d rather go for an new motor.

[@Zacko2341]

Vielen Dank für das hilfreiche Video! Gibt es eine Möglichkeit die Motoren zu reparieren? Ist es möglich die Kabel nicht von der Platine zu lösen sondern an einer Stelle zu durchtrennen um sie mit einem neuen Motor (+ Kabel) an einer anderen Stelle zu verbinden? Sehe den Vorteil als Lötanfänger, möchte die Platine nicht beschädigen. Vielen Dank!

[@AReResearch]

Beides ist möglich: man kann die 8520 Motoren mit micro JST Steckern bekommen und das passende Gegenstück unterhalb der Kabelführung an das von der Platine kommende Kabel anlöten. Nicht schön, aber machbar. Auf dem YT-Kanal von Toolshacker gibt es ein Video wie er einen 8520 Motor repariert (Kabel und Bürsten ersetzt). Das ist aber ziemlich gruselig und sehr fraglich wie lange man daran Freude hat. Selbst eine verbogene Motorachse, wie sie bei Crashs gelegentlich vorkommen kann, würde ich nicht gerade biegen sondern den ganzen Motor ersetzen.

[@JonnyU_Survival]

Have you tried replacing a rear motor ? There seems to be an additional 3rd wire ??

[@AReResearch]

Fortunately I had no more failed motors. But I know what you mean: The additional wire is the WiFi antenna. It does not go all the way to the motor.

[@jaygour]

Hey my motor getting heat (the one which i replaced)

[@waqarjavaid1929]

Where you buy this Motor

[@AReResearch]

It is this one: www.banggood.com/2Pcs-8520-8_5x20MM-28000RPM-2_1V-DC-Brushed-Coreless-Motor-CWCCW-71mm87mm-for-DJI-Ryze-TELLO-Drone-p-1284632.html?p=NT1005763073201409DA (Set of two motors)

[@user-zw1oy9tm4l]

W

[@sifungstudio2510]

Where are you from

[@AReResearch]

Southwest of Germany. Where the nice cars come from :-)

[@sifungstudio2510]

Can you repair my drone motor problem

[@flemming2jacobsen911]

A few drops of IPA will make most hot-glue let go.

[@skytechandgizmosmartinez7914]

what is IPA? tnx

[@explorespacelive]

@@skytechandgizmosmartinez7914 isopropyl alcohol

[@chanakyameher]

Can we join the new motor, to the cutted wire of old motor? Will it work!

[@AReResearch]

Yes, no problem. That will work. It just might not look as nice.

[@chanakyameher]

@@AReResearch k! Thanks

[@chanakyameher]

@@AReResearch btw I tried replacing the motors, but it didn't work. It seems like their is no electrical output to the broken motor's wire when flying, whereas all the other three motors work.

[@AReResearch]

If you are sure, both cabling and motors are fine, then the motor driver is blown. You will need to replace the mosfet transistor on the PCB as described here: tellopilots.com/threads/motor-driver-ic-mosfet-type.2165/