Terminating Fiber Optic SC Field Connector (APC and UPC Fast Connectors)

How to Terminate Fiber Optic Cable?
Materials Used in the Video
-------------------------------------------------------------------
Fiber optic Stripper: s.click.aliexpress.com/e/_DBj...
FC-6S Fiber Cleaver: s.click.aliexpress.com/e/_DCA...
Optical Fiber Visual Fault Locator: s.click.aliexpress.com/e/_DBi...
SC Fiber Connector: s.click.aliexpress.com/e/_Dk0...
Fiber optic cable termination process is done in termination boxes specially designed for this process. These special boxes are of two different types as wall type and cabinet type. Fiber optic cables cannot be used alone. Fiber cable used in any project is pulled up to network cabinets or termination boxes. After termination, each core of fiber cables accesses network distribution devices (switches) called active devices with fiber optic patch cables. Female adapters called “Couplers” are used to combine fiber optic cable and patch cable.
ST (round view) or SC (square view) connectors are used as standard products in Fiber Optic cable terminations. There are also connector types such as MTRJ, LC and FC.
Fiberoptic terminations must be made end-to-end with minimal loss. For this reason, it is recommended that the workmanship of each connector be done by expert technical personnel. Because the fusion device needed for the finishing process is also a very expensive material, it can generally be used by teams with technical knowledge on this subject. Today, EPOXY connectors are widely used. The feature of epoxy connectors provides the termination (termination) of the fiber optic cable to the connector by means of special adhesives. Adhesives can dry very quickly, and are ready for use in a short time.
Special equipment is also used during the installation of fiber connectors. Fine and precise pliers for stripping the fiberoptic cable, a cutting pen with a diamond tip to cut the ends of the connector, sandpaper finer than 0 mm to clean the overflowing part from the connector, a microscope to visually check the terminated ends, and finally a fiberoptic test for testing these ends devices are used.
The tips are measured in decibels, and if the results are high, they are cleaned with sandpaper and brought to appropriate values. If these values ​​cannot be obtained at the end of the sanding process, a new one is inserted in place of the installed connector and the system is operated. This process is continued until the system starts up.
Thanks..
AHMET RIZA KORKUT
The Future Is Now
/ ahmetrizakorkut
Apartmanda Fiber İnternet Altyapısına Nasıl Geçtim?
• Apartmanda Fiber İnter...

[@GelecekSimdi.]

GELECEK ŞİMDİ OLARAK COMNET 'İ ÖNERMİYORUZ. COMNET MÜŞTERİYE OLAN TUTUMLARI, SORGUSUZ ABONELİK SONLANDIRMALARI, KURUMSALLIKTAN UZAK TAVIRLARI, PROBLEM ÇÖZME KONUSUNDA YETERSİZLİKLERİ, MÜŞTERİYİ ABONELİK SONLANDIRMAKLA TEHTİT ETMELERİ GİBİ SEBEBLERDEN DOLAYI TARAFIMIZDAN ÖNERİLMEMEKTEDİR.

[@thomasdanuch9352]

Sehr gutes Video, endlich habe ich gelernt wie man den Stecker richtig montiert. Dankeschön!

[@muratbor6739]

Çok teşekkür ederim.

[@mspkizlar000]

Eniştecim videoların çok güzel ellerine sağlıkk💕🌸

[@bekirozcelik139]

Elinize sağlık usta. teşekkürler

[@sevvalermiis3034]

Faydalı bir video olmuş 👏👏💯

[@PIDOtomasyon]

Teşekkürler

[@edaningozunden]

güzel çalışma.

[@user-hf6go4se6m]

Music kinda lame, but great video brother

[@dylankane3754]

My fiber seems to have 4 cores is the process still the same?

[@RandomNullpointer]

Thank you for the video description.

[@oguz6270]

her konnektör yapımında giyotin ile kesmek zorunda mıyız

[@peace4128]

Abi paylaşımın için çok teşekkürler. kullandığın kablonun tam adı ve kodu nedir.sadece obk yazmışsın ama onun bile bir kaç çeşidi var o yuzden soruyorum.iki daireye toplamda kaç metre kablo almalıyız.

[@ahmedraafat2344-p8k]

تركيب connector