Testing the Servo Motor's Resolver

[@captainjinx42]

Great video. For these kinds of things I prefer using my analog scope. It “feels” better.. no idea how to explain that but I think you get it.

[@PeepawMcDonald]

Yes, you are correct. I love seeing a waveform on the CRT. And knowing that that very waveform is what I am actually seeing. And not processed and printed to an LCD before I am able to work with it.

[@alibinnasiralharthy2911]

Please add a video for aligning the Ac Tacho generator with servo motor.

[@alexscastellano5806]

Excellent video greetings from Venezuela

[@PeepawMcDonald]

Thank you very much. I am glad you liked my video.

[@김김사랑-x1i]

alexs castellano ㅈㅅ.ㅅ

[@김김사랑-x1i]

0ㄷㅇㅈㅅㅈㄴ.ㄴㅈ

[@keithminchin1817]

I like the X-Y mode. I’ll try that tomorrow! 👍🏻

[@wanderpadua8172]

Good evening! Do you have a video that teaches how to synchronize an encoder with the Siemens motor?

[@tindicio44]

does resolver need calibration?

Can i see the diagram how your wired up the sin, cos and excitation ?

[@alexanderadsl4983]

Hello mr.McDonald! thanks a lot for yours videos, it very useful, and I have a couple of question about resolver. 1. Which connection of the motor - Y or Triangle ? 2) If you put +5V to the U phase, and GND to the V phase, and 2(a) is it works on both Y and triangle motor? 2(b) do I have to set signal COS in MAX, or signal SIN in MAX position by oscilloscope 3) what if I make wrong place SIN and COS position? Will motor work? 4) What if my drive doesnt show any errors, but there are not enought torque on the shaft?

[@qzorn4440]

sweet video... BK test equipment has been around for a long time and works well..... thanks...:) great resolver info... is there the hobby version ab-ultraware servo software?

[@elmnaoirfer3751]

If we set 7 volts in the primary coil, what will be the peak voltage in the cosine coil at angle zero Is it 7 volts or less? The rule to find out the peak voltage at angle zero is as follows (peak potential of the cosine signal = voltage on the input coil x cosine of angle sita) (V cosine=Vr x cos cita)

[@marianlegut4970]

Hi, how i can find a "dead motor postion" in Ac servomotor? Same as dc with dc power supply? Its posibble? Thanks for yours great's helpful videos

[@mahirerensan]

Thanks for your labor.

[@homemade83]

your channel content is very rare thank you so much for sharing that with us. i hope i find a way to contact you some times for some help.

[@compoundeffect3070]

Hello Sir! from this test, how do i understand whether the motor's resolver tighten position is okay or not? Please ans me Sir .

[@ohmsautomation1010]

Hello.. Thanks for this video and is it possible to convert the signal in to angle value..

[@anusbilalbilal7140]

Hello sir can you kindly tell me how to align encoder of AC Servo Motor.?

[@manghecky]

i love this guru

[@marciohogenelst]

Dear Mr Peepaw, do you have the electrical diagram about it ?

[@gomeshaity8206]

kzbin.info/www/bejne/n5Wzooqpm9eiorc

[@swm1975]

I would like to email you with a few questions if you don't mind.

[@antoniomatamoros6961]

Thank you so much, awesome.

[@PeepawMcDonald]

You are very welcome. I am glad that you enjoyed my video. Troubleshooting and repairing electronics has always been interesting to me. And I always enjoy seeing other folks who share an interest in electronics. Thank you very much.

[@Sailingon]

I've just got an oscilloscope and going to have to borrow a motor to try this

[@PeepawMcDonald]

Great on getting a new oscilloscope. My two best work friends are my oscilloscope and digital-multi meter. HaHa. Thank you very much for watching my video.

[@italoquaglioify]

maravilha muito bom ta de parabes

[@muhammadarief192]

thanks for your video,,,, can you help me, please send me your picture diagram installation during calibration

[@CNCmakers]

Thanks for sharing

[@ravikantkewat6893]

Thank you sir 😊😊

[@amjadhussain1836]

Can anybody give the data of this resolver company name LTN model RE21-1-d64

[@sawomirs8949]

Greate video. I want to open small servo motor servis in Poland. It is posibilit support me?

[@sdfssdfsdfsdf]

Hi, when r u open?

[@repairtech9320]

Thank you so much

[@roseateelectronics8498]

Hello sir. Kindly sir send me the video of lenze drive 9200 or other change the parameter and save the drive through of global drive software. Thank you very much

[@marciohogenelst]

Hi,,, do you resolv your problem ? Do you have the procedure of test to resolver ?

[@vinnatv4150]

Thank you boss

[@clei-mult4475]

excellent.

[@elmnaoirfer3751]

If we set 7 volts in the primary coil, what will be the peak voltage in the cosine coil at angle zero Is it 7 volts or less? The rule to find out the peak voltage at angle zero is as follows (peak potential of the cosine signal = voltage on the input coil x cosine of angle sita) (V cosine=Vr x cos cita)