The best budget resin 3D printer? Longer 3D Orange 10 review

[@albertvillalobos1377]

You and makers muse are standing above the others and I enjoy both channels, thanks for the review.

[@GilDev2]

Don’t forget CNC Kitchen!

[@melvinch]

Incidentally both are Australians. Any reason why 3D printing is so happening on that continent compared to elsewhere ?

[@larryb6759]

I picked up an Elegoo Mars a couple of days ago. I watched many videos on resin printing so I know the things I needed to be careful of before it arrived. It is a very nice printer and I have printed upgrades for my FDM printer when it arrives. Thanks to you and other KZbin content creators for the useful information!

[@Insomnii95]

this thing was on sale for about 120$ during prime day. got a full setup (resin, goggles, gallon of IPA, container, funnel, gloves) for around 220. looks nice especially for what i payed for it.

[@chriswesley594]

Michael, as far as I am concerned you are a legend, a machine and a fantastic bloke. You've helped me a lot on my 3D printing journey, and I thank you for that. But Google's mid-roll ads, spaced every THREE MINUTES are really destroying the experience of watcihng your videos. I know making videos is a lot of work, and often thankless. I have a channel and I run ads, but not mid-roll ads. So my plea is to dump the mid-rolls. That's just my 10 cetns worth.

[@Musicmaddnes]

I find your videos the most useful out of all of the guys on here. I started watching you through the a20m bl touch. You always stress test way more than the other youtubers.

[@zensoul8335]

I see others asking about a video reviewing the Longer 3D Orange 10 vs Elegoo Mars & Anycubic Photon. I'd like to request the same, please. I really trust the info I get from teaching tech above most other review channels, so I would love to see a video about this as well as clean up & maintenance recommendations/tips for a good setup & work area.

[@Jerewie]

+1000 for Longer 3D vs Elegoo Mars vs Photon S ! :D

[@octapc]

Ya, the Photon-S

[@ttp_007]

The Longer only uses is 854x480. While the MARS and PHOTON uses 2560×1440 2k resolution. Without a doubt you'll get better print resolution off the MARS and PHOTON.

[@MrDehicka]

Photon S clearly - resolution + more rigid Z column design.

[@MrDemon891]

I have a Form 2 but it's nice to see that there are coming more and cheaper options which are maybe not quite as good but good enough :) Thank you for testing this printer. It would like to see more tests of different SLA and SLS printer. Everyone is testing standard printer but not resin printer.

[@stevesloan6775]

Excellent video... Thanks for taking the time. I’m borderline going to buy one of these as my first 3d printer. I’ve done a good amount of carbon fibre and understand the need for skin protection and more importantly air filtration. You could do with a serious upgrade safety wise.

[@ydoweneedapass]

I dont usually comment, but i have to tell you that you have too much potential, keep growing and keep doing what youre doing. cheers!

[@rubberonasphalt]

The toxicity of printing resin is scary, and I think a lot of people are underestimating it's potential harm. You definitely need to wear organic filter mask and gloves, but also practice hospital surgery level of discipline. Which in the consumer space, I don't think people would follow. I might stay away from SLA because it also looks way too finicky, and way too unsafe. Like asbestos level of unsafe.

[@aggronn]

Looks good, just got an ELEGOO MARS UV LCD since it was also way cheaper but didn't have time to print yet. Hope you will review more cheap resin printers

[@redkingrauri3769]

Same here. Best of luck with your prints!

[@jacobrollins37]

Some day I will get a resin 3D print but, like you said, I need to get a safe place to use it. That is not easy with a 3 year old.

[@3DJapan]

I just bought one of these as my first 3D printer, although I've done a lot of work with printing on Shapeways. While it is my first I've read up a lot on the safety. I plan to keep it in my garage with the garage door open when possible. And of course I'll be getting additional gloves to go along with the ones that come with it. It hasn't arrived yet so I'm excited to do an unboxing video when it does in a few days.

[@johnhennessy7283]

Hi Phil, I am looking St this printer also and where did you buy it and what resins did you get with it.

[@3DJapan]

@@johnhennessy7283 Hi John. I got mine from Amazon. It hasn't arrived yet but I see it comes with one bottle. I also bought a bottle of Anycubic grey.

[@johnhennessy7283]

@@3DJapan , You are in Australia, I am looking at getting one to get a better parts finish than my Cocoon touch ( which has been fantastic ) but looking for better finish. John Hennessy.

[@timester9693]

I am thinking of getting a resin printer as a nwbie. One thing I would like to know is if this model is capable of doing lithoplanes and if so how big? Also I have seen lithoplane light boxes and would like to make those as well.

[@jmtx.]

Great review! I'll hold off till better chemicals come along - not a fan of messing with all this in a home environment.

[@TeachingTech]

Fair enough, it's an important consideration and not everyone has the space to set it up optimally.

[@BenCos2018]

@@TeachingTech do u know if the ender 3 upgrade board can be upgraded over USB? and if it has thermal runaway protection enabled? Thanks www.amazon.co.uk/gp/product/B07TLSSRVN/ref=ox_sc_saved_title_2?smid=A10XQE2DVH1KCY&psc=1

[@kleetus92]

You do realize that most women expose themselves to far harsher chemicals when they get their nails done in a salon, right? I mean IPA is off the shelf stuff at wal-mart, it's not like you need a Hazmat license to work with this stuff. I'm amazed at the level of fear everybody has with this. If you ever built a model with Testor's glue, or worked on a car, you've undoubtedly contacted worse material for longer than you would with this. I'm not saying this stuff is safe to eat, but you don't have to worry about getting eye cancer just looking at the bottle either.

[@jmtx.]

kleetus92 - it's the resins that are toxic.

[@BrianHallmond]

I was thinking of just doing it on a table in my backyard.

[@kenbessemer4913]

I am ready to buy my first resin printer. I am choosing resin because I create jewelry and they have the resin casting wax. Could you do a side by side of the few resin printers you have with casting wax and some jewelry models like rings with prongs so we can see if the claims that these will work are real? My hope is to print a casting tree whole on the sprue so I can eliminate molds, wax injecting and treeing by hand. When you think about small links for a bracelet (10 to 20 components) being done one by one compared to this it is going to make it possible to turn out more than one finished product in a week. If you can get a model of a casting tree with several jewelry items on it that would be the ultimate. Try asking Stuller as they make the software (rhino gold) to design these items. The other software is 3-design and Matrix they may want to promote theirs as well. Could be could source for a model file.

[@Schwift3D]

It's official every major 3d printing channel has now covered the new lcd resin printers 😂

[@truantray]

and they all look at ONE and claim it is the best.

[@davidurdahl6656]

Can't decide between this or the elegoo.

[@joncalmavergara3788]

how does the Longer Orange 10 fair compared with Elegoo Mars?

[@tehKaito23]

+1 just checked amazon (germany), currently have nearly the same price

[@josuerodriguez7658]

No, i bought one cause at first it was the only one that would ship to PR but quality is not the best, i had to replace the screws on the resin tank when i removed the FEP film. after a month the screen just died and was having multiple failures before it completely died. this is the Anet 8 of resin printers not worth the money. end up buying an EPAX cause Elegoo or Photon won't ship to PR

[@tehKaito23]

@@josuerodriguez7658 that does not answer the question I think

[@68HC060]

I'd probably still go for the Anycubic Photon; it has 2K screen and is $259 (including 250ml resin and FEP film) - so $30 extra isn't much.

[@jeans.plescha1480]

Thanks for the review. The health aspects pretty much placed this on on the back burner for me, I am new to 3D printing just starting so yeah, not there yet.

[@LT72884]

I have this printer, and stopped using it because nothing every sticks to the build plate.. bad resin? Wrong type of resin? What else could it be? Thanks

[@LinkWulluf]

Long time no post. love the videos as always. I'm getting into D&D and am at the point where I want to start printing my own custom mini figs for myself and the others that I play with. I only have the Ender 3 (original with a few mods with help from your videos). I like the Ender 3 but I'm hoping for something with more speed and better detail at the mini size. you have a few printers now and was hoping that you might could give some advice based on your own experience with the many printers. I'm leaning between something like the Monoprice Mini Delta 3D Printer and the Longer 3D Orange 10. Could I talk you into maybe bashing off a mini fig prints of the same thing on both and giving a quick review video comparing the speed and detail at that size? I'm sure you have a full plate right now with a lot of videos planed out not even counting the ones I'm sure still need to be edited. if a video is too much. In your own opinion of the two what one do you think would be better up to the task? or is there another better option that I may not have considered ?

[@altar7885]

Thanks for the video. How long did the printing take?

[@Inventorsquare]

If increasing the off time before UV mask helps with those zebra stripes, and they are always in the same orientation, then they might be caused by the residual flow of the resin after every peel.

[@kleetus92]

I'd be willing to bet it's more a function of the surface angle of any particular print and the step size. I thought he said he was doing these at 100 micron, personally I'd have redone the one at 25 micron to see if the condition still existed.

[@truantray]

All you need to know: Anycubic photon masking screen is 2560*1440(2k)HD. This cheap knockoff is 854*480. The XY resolution for MSLA is poor for the Orange 10.

[@yaminae.mohand4065]

But said is possible to change Orange 10 LCD for the 2K LCD: LS055R1SX03. Isn't it?

[@Krytern]

@@yaminae.mohand4065 Shhhh, let the gatekeepers believe they have to spend more to get into the hobby.

[@robertsecor5738]

Have you updated the firmware? I did and no fan now. It has the 2 pin plus 1 blue pin and requires firmware D revision, but once applied the fan will not power on. :(

[@manny75586]

Thank you for this. I've been really interested in getting into 3D printing. This looks like exactly what I wanted.

[@spicybeen4354]

I would say the ender 3 is better for just getting into 3D printing but If you already have a fdm printer then that’s fine

[@JulianBartlett]

Id love to see a comparison between Longer3D Orange 10 and Elegoo Mars any chance you can review that next?

[@TeachingTech]

I don't have one but feel free to request they send me one and I'll make that video.

[@WhamBamSystems]

Interested as well!

[@JulianBartlett]

@@TeachingTech I am also a youtuber but I dont have that pull with or the connections with the right people :)

[@ToastmastersFCSS]

go with the elegoo- it has a larger print volume. I do like the screen on the Longer a bit better but wouldnt trade to have a bigger build area, and the color enclosure comes fully formed not in 2 pieces like the Longer.

[@rmawatson]

be great to the photon compared along side these two as well by a single reviewer.

[@DJalin1]

Any change of a fan upgrade video. I noticed a 3d printed fan update for the bottom of the printer but there were no introductions with it. The original fan is loud.

[@duke1252]

I just bought my Longer 10, my only question is, have you had any success with using other branded resins and have any suggestions on printing with other 'recipes'?

[@cobbarne]

I just bought one of these. I had several issues on day one and now it won't even turn on. I emailed their support team today, so let's see how they do.

[@ttp_007]

The Longer only uses is 854x480. While the MARS and PHOTON uses 2560×1440 2k resolution. Without a doubt you'll get better print resolution off the MARS and PHOTON.

[@promountaincoffee]

What resin you use?, I'm interested on use flex polyurethane can I use on this device? or wich one I have to buy, THANKS!!

[@drolsisusej100]

we have a spare bathroom , would running the printer in the bathroom with the vent fan on be safe enough for fumes ?

[@johnhennessy7283]

Hi Michael, I thoroughly enjoy all of your videos , they are easy to listen to and have all the answers . I am looking at going into resin printing and would like to see more on different products and most importantly the different resins available and what you would use them for. Thank you for your work and great videos. Regards John Hennessy.

[@ShadowDrakken]

In general, print in place articulation doesn't work on resin printers unless you have VERY loose tolerances. Resin curing bleeds out from the cure spot just enough to ruin tight tolerances.

[@novakane8722]

Based on this I'm glad i backed the orange 30 on kickstarter

[@lexgoth2005]

Same, along with the positive review by the Printing Nerd. Have you had a chance to use the 30 yet?

[@rodsprague369]

Are there good reviews of the software used to design things from scratch? I am horrible at wrote memorization, so I need a very logical environment that does not turn learning the functionality into an Easter egg hunt through pulldowns within pulldowns, like with MacroShaft products.

[@luisdominguez4307]

Can you grab any 3d printer file and use it with this maquine????

[@hugoarguelles2202]

Hello! Do you think this 3D Printer could be used for dental purposes? Such as prothesis like crowns and bridges? And by the way, do you know about a 3D scanner that might be useful for the same purposes? I know there is dental printers and scanners but they are super expensive. I love your videos!

[@MooseWithAnAxe]

I have attempted to print 3 different miniatures on my Longer 10 (which is quite time consuming, considering you cant see a failure until roughly 2 hours in, along with then having to take an extra 20-30 minutes after to clean up the failure and reassemble everything). The failures seem to be coming from the fact the the supports put in by the software (much like shown in this video) are placed under the base of the miniature. Each time I attempt a print the supports under the base come out fine but it seems like they fail and the base (and everything after it) fall and end up as a solid mess on the base of the resin pool. Would you have any suggestions for dealing with this issue? I'm preparing to shelve my attempts at Resin/SLA printing given these failures and just stick to using FFF/FDM style, but I really want the fine detail that comes from SLA.

[@mattiash8187]

Where can I download that bulb vase thing with diamond texture? You call it a bassi or something like that. There isnt a link for this one in the video description. It looks really nice and i cant find it even i searched quite much on net.

[@brezovprut4431]

Longer Orange 10 vs Anycubic Photon ?

[@5punkybob]

The photon is better because of the screen resolution is much higher so you get a more accurate image projection

[@whatimintonow8608]

Just wondering have you checked out the longer orange 30?

[@jasonbenyeda1476]

The slicer for this printer seems amazingly good. What is the file format? Can Chitubox or Prusa slicer be used as an alternative?

[@shadow7037932]

Looks like it only supports their slicing software.

[@Mario29615]

I've seen that you review this products quite often and when are recently available but how much time does they work after failure? How many prints until dying? The warranty will cover?

[@TeachingTech]

I have to strike a balance between using them for long enough to understand the workflow and issues and actually making a video. I typically have a printer for about a month before I release the video. If anything significant happens after that I'll update the original video.

[@Mario29615]

@@TeachingTech thank you so much. I'll be watching for some news

[@jasonbenyeda1476]

The LCD and UV source on every resin printer I own is considered a consumable by the vendor. Unless it fails within a VERY short period, you have to replace at your own cost. Both of these are good for several 1000 hours usually. If you are using these printers in a production environment, you will want to keep a LCD, UV source, build plate and 2 vats as a minimum spares kit. The vats are critical because if you have a failed print, you can just swap in a new vat and start a another print. Cleaning adhered resin from the bottom of the FEP takes some time.

[@Mario29615]

@@jasonbenyeda1476 wow Jason, thanks for the advice I didn't know that.

[@janwiersma1449]

hi Michael. did you use Chitubox yet? i have got the alfawise w10 which is internally and actually externally eccept for the color of the acryllic hood eccactly the same printer, it even comes with 250ml longer resin. and the files has the .lgs extension. now my problem. i had an object which could not been sliced with the propietary slicer. holes turned into massive in the next layer and object get screwed in every way. yes it's a difficult object i guess. but Chitubox can handle it. but there isn't a real profile for the longer in chitubox. when i make a default profile based on for instance the sparkmaker it gets the extension .wow how can i get it working on the longer/alfawise? any suggestions? great vid.

[@elfpimp1]

You should consider getting a hazmat locker or making one of your own.

[@RahmatHidayat-ul6qg]

If we buy this machine. We have sofwere to.? Thanks

[@a1crosenberger]

What if you take two color resins that are similar to the uv curing time and pour them together in the vat? Could you get a marble effect?

[@TeachingTech]

I think yes, but the effect will fade as they get mixed during the print by all of the churning.

[@5punkybob]

All it needs is a 2k screen upgrade and it would be mint

[@Steger13]

Hi, is this printer good for making head sculpt and figurines of 1/6 scal or 1/12 and 1/4 scales? Or you have an other one in mind? Thx

[@Knightridermsn]

Do you need supports?

[@nottingham82]

This price war is great. Just got a photon used for $200.

[@talonabuser1072]

What’s the community support for this like?

[@AlbertoMartinez765]

This thing is down to $179 on amazon ! ( since the Newer Longer 30 came out, has 2K resolution and a slightly bigger print size and angled plate but cost 100 bucks more)

[@DocsPropShop]

Link?

[@howiebaird5511]

right on dude you reviewed it

[@james10739]

What is the cost difference between fdm and resin

[@toms.3977]

Checked Amazon...no longer available. That was my only option. Loved the video but it only made me fall in love with something I'll never own.

[@truantray]

Anycubic Phpton is better.

[@capsyzeable8790]

If you consider the current exchange rate, the Orange is $339AUD plus delivery... Aliexpress is $365 delivered (with no Australian warranty or support).... Not exactly the "budget" 3D printer it's being promoted as. At that price the Orange Longer is up there with the Anycubic Photon through an Australian reseller (which comes with Australian warranty and support)... Kinda made the decision easy as hell.

[@Ones2Cents]

Tom S. They are back on amazon for 200 dollars

[@quantumenergysolutions9128]

Thanks, Do different property resins exist? eg, harder,softer,flexible,impact resistant? Cheers!

[@hatchbackhound]

Got my unit about 3 weeks ago, already out of resin.. how long till we see some upgrade videos.. I'm thinking that fan could be loads more quiet.

[@BrianHallmond]

How many prints did you get done before you ran out of resin. Were you happy with the quantity?

[@gregp.5064]

is blue cast neccessary or could you do jewelery with normal resin?

[@mrfordf3508]

How is the speed with the LCD vs the laser of the Peopoly? Can you print identical items and publish the print time? From what I have read, LCD type resin printers need a different type of resin than the SLA printers. Is that correct?

[@charleslao3798]

Yes, LCD resin is different from a SLA printer resin

[@shadow7037932]

Any chance you can review the BEAM3D Prism? From my understanding the Orange 10 uses a proprietary slicer where as the Prism is more open and supports multiple slicers (Slic3r, Chitubox,etc). As you know, well maintained software makes a good bit of difference in print quality/ease of printing. Plus the Prism has auto leveling and would like to see how good that is.

[@reluttr2]

the Prism uses the same auto leveling system as the Monoprice MP Mini SLA.

[@blackwolfecc]

Whelp... I’ve been looking for an excuse to get a resin printer. I WAS going to get the anycubic photon, but @ $408 I couldn’t convince the wife. At just over $200.. I honk this is the one! Thank you for such a good review!!!!

[@capsyzeable8790]

In Australia the Orange Longer isn't stocked locally, can't be ordered via Amazon (due to their stupid restrictions), and only available via Aliexpress/Alibaba (so no local warranty or service support)... Add the local exchange rate and the price is up there with the Anycubic Photon (which is available in Australia from local resellers with warranty and support)... Sure, may be "budget" to everyone living in continental America, but for those living in Australia it's not the budget printer that it's being promoted as.

[@blackwolfecc]

Cap Syzeable wow that’s ridiculous. I’ve known prices were higher in Australia but didn’t think it was that high. I wound up getting the standard Photon and it’s been fun so far.

[@capsyzeable8790]

@@blackwolfecc ... Yeah, I was excited when I saw the reviews of the Orange, especially at the price point that was being displayed around the net... I've heard a lot of things about the Photon and seems to be the way to go.. What's the long term reliability of it been like? Any issues?

[@blackwolfecc]

Cap Syzeable I’ve had one failed print so far and it was my own fault. I’ve already gone through the 500ml bottle of green that came with it and am pretty impressed. The Anycubic community is pretty good and replacement parts are abundant and fairly cheap. But, unfortunately, I’m speaking from the states. Cleaning has been the only tedious process. I built out a section of my garage specifically to house this and any other resin printers I might get. Blocked off and ventilated with work space for a cleaning process. Resin on a special self, sonic cleaner, couple alcohol baths, and all the tips needed for cleaning. I’m super cautious about the material. Another machine that’s been doing well is the Elegoo Mars. Was for sale for $250 state aide beginning of July, and sold out super quick. I haven’t seen it back in stock yet. Same with the Orange. I’m planning on picking up both as soon as they are in stock and comparing them to the photo . Would eventually like a Photon s, but that’s more for convenience.

[@BrianHallmond]

How long does it take to print something like the Trex head?

[@maidenjump]

How about Vat and clear film attached? For how long do they last? Please provide information..

[@TeachingTech]

The vat will last forever, the FEP film in my experience on two other similar machines lasts until you scratch the surface by accident. FEP film is cheap and you can buy FEP intended for another printer. Generally the sheet comes oversize and is trimmed down with a blade after being clamped into the VAT. Worst part is having to clean out the old resin from the VAT first.

[@maidenjump]

@@TeachingTech thanks for reply, and for this video

[@maidenjump]

@@TeachingTech forgot to ask,.. where it will stand against wanhao D7?

[@jasonbenyeda1476]

The FEP film will eventually wear out due to UV damage. It is many hundreds of hours. You are more likely to damage it with a failed print or cleaning before that.

[@DisgruntledPigumon]

So. Elegoo Mars or Longer Orange?

[@josuerodriguez7658]

Elegoo any day! Orange is not worth the money...

[@teabagNBG]

the baby figure is really dope where can i find the file? thx

[@mrclown7469]

That CR10Max sure did make a mess of your desk 😆

[@praveenraikar5353]

How to print our own picture design....

[@car5on777]

Michael, Thank you for the great content! Would you be willing to review a budget 3D Printer with Dual hotend/nozzle? Or maybe even a mod for the Geetech A10M to add dual hotend/nozzle capability? Thanks!!

[@Atrac89]

where is the skull stl?

[@BarringtonDailey]

Can you at least prime and put a wash on the miniatures. Looking at those blanks we've no idea whether those miniatures are any good or not. Cheers.

[@mlc-projects]

how thin can your walls be when printing

[@0xCAFEF00D]

I'm really tempted.

[@elfpimp1]

Wow. The detail!!

[@Moctop]

Longer3d Orange 10, Elegoo mars, or Anycubic Photon?

[@lukeolson8224]

Moctop I am wondering the same thing!

[@zensoul8335]

Me as well. I really trust the info I get from teaching tech above most other review channels, so I would love to see a video about this as well as clean up & maintenance recommendations.

[@avejst]

Impressive prints Thanks for sharing 👍😀

[@HugDeeznueces]

Where is the Epax???

[@multiaxismachines538]

Man this is so cool

[@markgiles8527]

Amazing details! Stronger in all Axis than FDM so I’ve heard, which could be useful. Nice one.

[@OwenWithAHammer]

Check out the Anet N7 next pls, it's a 300mm build height resin printer for $1500, I want to get it but there's no reviews anywhere.

[@cyruss2946]

Have you tried any castable resins !? Thank you.

[@TeachingTech]

On this printer no, but I have a playlist on designing, printing and casting rings.

[@ZakuNuva]

I don't get why people are looking at this and not the Elegoo Mars. Great printer and is $250 right now with a 2k display.

[@truantray]

because KZbinrs are getting this shipped to them to try. Don't go by the annoying clickbait title of "best" -he only tried one.

[@3DPrintingNerd]

I have this and the Elegoo Mars coming to me. The Orange 10 arrived first, so it's video came out first. I'll have a video on the Elegoo Mars once it's arrived and I've gotten some use on it.

[@ZakuNuva]

@@3DPrintingNerd I got mine yesterday, too me a few tries to get a good print, turned out you REALLY need to tighten the build plate set screws. Use a quality hex key as to not strip anything. I've had some of the best prints ever out of it a though some issues with adhesion but that's probably my fault with lack of support structure and experience with msla

[@MrDownRater]

so the question is: Elegoo Mars or Longer 3D Orange 10?

[@davidurdahl6656]

Right? Im leaning towards Mars,if it's still on sale when I have the extra dough.

[@MrCcfly]

@@davidurdahl6656 i think anycubic photon is in that same price range

[@davidurdahl6656]

Photon is almost twice as much. I know they are more tested and approved, but idk if I wanna spend that on something I won't use near as much as my fdm printers.

[@MrCcfly]

@@davidurdahl6656 230 vs 250 $ not that much different

[@MrCcfly]

photon is 250 $ so these don't seem to have logic to buy it ,but it's your $

[@Matthew-jv1ee]

Great review mic..only problem i have with these cheap lcd printers is the lcd...how long will this lcd last...and how easy is it to get parts...the lcd would be the major cost in one of these units....open it up and chq what stepper they are using for z axis...thanks mic

[@TeachingTech]

Something like the Wanho D7 has plenty of spares now, it remains to be seen whether the new generation of resin printers will receive the same support.

[@jonathonhoogland9446]

Matthew 1973 they are all likely using mass produced phone panels so the part cost is actually extremely low.

[@MrMeddle2243]

I got one of these and loaded the software and when I try to generate the supports the program closes, ive tried to contact the company but never hear back from them, so I have never got to try any of my own parts, any idea whats going on?

[@noway8233]

Maybe its yuor computer, try to use another one

[@jamesmoe]

I am wondering why they are sending out review units of the Longer 10 when they just wrapped their Longer 30 Kickstarter that will ship shortly

[@MrCcfly]

is that 30 new same kinda model like this or bigger ?

[@jonathonhoogland9446]

MrCcfly Bigger. Roughly the same as Prusa SL1, but no tilting bed and roughly half the printing speed.

[@charleslao3798]

@@MrCcfly 30 has a 2K LCD screen. Higher resolution.

[@dibblethwaite]

It's a bit misleading to say it t works exactly the same as a moai. In the time lapse, the tilting bed on the moai is really obvious. That's a really important difference. You'll get more failures without it.

[@goldstandard7406]

What were your print times?

[@antoniobeltran4204]

Will you try Beam3D's "Prism" mSLA printer?

[@poman911]

These resin printers have a hidden defect: the LCD display under the resin tank gets damaged by the UV light. Get on the FB group of the Phrozen and other printers and you will see problems after problems with the LCD screen. This type of printer isn't ready for reliable yet. I'm going back to FDM.

[@tinplategeek1058]

Hardly hidden as it is mentioned in the video. The LCD screen under the resin tank is a consumable item and will need to be replaced.

[@poman911]

@@tinplategeek1058 well it was failing because there is no tempered glass between the FEP screen and the LCD screen. Any pressure from the build plate on to the FEP screen will be applied to the LCD screen. In less than 40 hours of printing, I had two failed LCD screens. The fix was to mount a tempered glass screen protector between the LCD screen and the FEP screen on the basin's bottom. There is a downside to this in that the focus point is slightly off due to the thickness of the screen protector. I can live with that loss in resolution now that the screen is reliable even after 100 hours of print.

[@tinplategeek1058]

@@poman911 I agree with you that it shouldn't fail fast. 2 screens in 40 hours is ridiculous. You would hope for a thousand hours plus of printing per screen. Glad you found a work around.

[@robertbobrichard]

Anyone else having trouble with the bundled software? Can I use a different slicer?

[@hatchbackhound]

Chitubox just released a saving option for .IGS. so we can now use it in the sted of longers slicer,witch is crap

[@astro7996]

Thanks for the great video once again!

[@projectigi]

lsn't longer = alfawise?

[@mode1charlie170]

Oh what a surprise....no longer available on amazon.

[@octapc]

It's also available on Banggood

[@billrex]

That sounds like an explicit website.

[@Bakamoichigei]

Source for that "big floppy storage container"? I'm not even sure what I'd _search_ for... 🤔

[@majorkuso6720]

Flexible tubs or storage bins

[@Bakamoichigei]

@@majorkuso6720 That found 'em, thanks! 👍