The Brand New Echo CS 3510 Review, Unboxing & How to Convert to a Carving Setup

The Brand New Echo Chainsaw CS 3510
In this video I unbox the saw Start it and set it up as it comes then convert it to to a carving saw.
Learn a few trick to save time in how I do that and get my real feedback. This was a very suprising review
Check it out let me know what you think and drop a comment in the area to name this saw
thanks so much for watching be sure to subscribe
www.echo.com

[@brianrobinson1401]

Had mine for 15 years still going strong

[@RyanCookCarvin]

love it

[@ewilliams19]

I just purchased the same chainsaw today and can’t wait to use it. Echo all day long for me!

[@RyanCookCarvin]

Good choice!

[@kevintulak9987]

I think you should call your new saw Gilligan, because it is going to be a great little buddy. Thanks for sharing, learning lots.

[@RyanCookCarvin]

kevin tulak I like that

[@KM-os4be]

Now that's a colorful review. Just picked up a new Echo 4510 wood saw.

[@clawhammerinc]

thank you Ryan you answered all my questions, you are the man thanks i got my 3510 for 200 new at the flea , it is a bad assss saw for carving, name yours lucy, she was a sweet gal back in high school but she was bad assss, lol thanks my friend, ive learned alot from your shows, will be trying to get that cannon 12 inch from ya, cant wait thanks again

[@chainsawcanuck]

I don't carve.. But collect saws and cut alot of firewood.. And love your review.. Thank you

[@RyanCookCarvin]

Right on

[@ralph9255]

Sparky ! On account of the sparks from the new bar !

[@CarvingFusion]

The duster!! Great video's man!

[@jamesward5721]

I have the older model - it is an epic saw. I reckon this saw will be a little beast - I have worked its older brother close to death - it refuses to die. Starts second pull after 1 pull on choke - every damn time. Predictable & reliable - which I value. Put it this way - the only other saw I'd "Like" to own is a Stihl MS881 - all the other saws bore me & I own a lot of saws. I pick the Echo up above everything else daily. I think if you owned an Echo 35 series & a Stihl 881, you'd have the entire world of chainsaws covered.

[@Rmrstudio01]

What's the drum he used? Would any cs 1/4 drum sproket work?

[@TheBobford71]

I love the echo saws. Stihl is a good brand saw, but I am an echo fan through and through.

[@gypsywolf58]

Thx so much for this review. I carve with Stihl, but I am EXTREMELY tempted to get one of these, and set up like you have it!! 4 oz. Lighter than still ms170, and easier for an old lady to start! Hmm I think her name could be Temptress

[@brianrobinson1401]

Cutting hard wood in south texas good saw

[@RyanCookCarvin]

sounds tough

[@mitchellfederico8429]

Hi Ryan, I have the cs-310 and the 3510. Which Oregon sprocket specifically did you use? I can’t seem to find a 1/4” anywhere for it. Thanks for all the awesome content!

[@elliotbaxter5709]

Hey @mitchell Frederico. Have you had any luck find a 1/4" sprocket anywhere?

[@mattfleming86]

Do either of you guys have a part number?

[@itsacountrythang1374]

I know this is a old video but did anyone ever find which sprocket to use for the part number? That'd be great I'm a beginner and looking for some help thanks

[@griffinswoodworks]

Ernestine ... sounds like an ole trusty saw from the get go...

[@spudbuckley4346]

Ryan...just like lot's of folks here I bought the saw and have worked with Echo support but can't find 1/4 pitch clutch drum and sprocket? I did find a 12" quarter tip bar with a 3/8th LP. Is there something wrong using 3/8th low pro for carving? I totally love your vids...I'm a beginner and you explain things so well.

[@brianrobinson1401]

Thay make good saws i did miner repars on it wood like a new one let me try lt

[@RyanCookCarvin]

thanks

[@axeandturtle]

Hello!! How can I get 1/4 drum clutch for cs3510??

[@Bearcarver2011]

Nice saw Ryan. Let’s call her Co-co

[@user-sf1fx4ux5f]

I wonder if I should buy such a saw, could you make a new video of how it cuts or fells a tree. Thanks 🇧🇬👍

[@joeraptor1]

Is the engine rated for 300 hrs of emissions durability? Thanks.

[@joeywallace7139]

Hey Ryan what sprocket drum do you use with that?

[@lightburning9693]

I can not find a 1/4" sprocket for an Echo CS310 anywhere! Im trying to outfit one with a 12 dime tip and .25 chain. Do you typically order one that is advertised for a different saw but works for echo?

[@keshmo12]

Good video. Do you have part numbers for that bar / sprocket drum combo? Looking to do the same thing. Looking to pick up one of these saws soon!

[@RyanCookCarvin]

I actually dont but ill get my echo guy to che k out the vid and see if i can do that for you

[@JesusRuiz-fg4bk]

The best!!

[@weirdalloysinc.]

i dub the "toothless", after the name of the dragon on "how to train your dragon". he was named this because he looks toothless until you get him mad!!

[@terrypach1664]

Cool

[@cardinalpoint6047]

The dagger!!!

[@elliotbaxter5709]

Ryan aka my hero.... Been trying to find a sprocket to run 1/4" on this but not having much luck. Is echo able to help with mods for carving setup? I'm no expert yet

[@Kyle_Harding]

Have any luck finding a sprocket?

[@elliotbaxter5709]

@@Kyle_Harding negative. I've actually reached out to echo and multiple saw stores online. Each one of them said that they have been unable to locate a 1/4 pitch sprocket yet. They said "when enough people ask someone will start producing them". You have any luck?

[@Kyle_Harding]

@@elliotbaxter5709 there are some oregon drums listed as compatible with some echo saws, not sure about this saw specifically but I found out the best setup is with a rims instead of drums, you can just switch out the 3/8 rim and bar for a 1/4 pretty quick, available everywhere, only the higher end saws come with rims most are drums

[@fastrivers812]

Contact Bob King here: sawnuts.com/product/echo-quarter-pitch-sprockets/ If this is like the 361P, which is what I have, he sells the sprockets and is where I got mine. He used to run echo saws. Not sure if he'd know about this model but worth a try.

[@elliotbaxter5709]

@@fastrivers812 Thank you! I'm still on the hunt for one so much appreciated

[@michaeltaggart01]

I’m late to the name game but I would say jimmy chain!

[@ian7583]

How about pegasus (the flying horse)😊 😊

[@ian7583]

Never used an echo love my husk thinking about converting to a craving saw what do you think 😊😊

[@tonyd1149]

Ryan, nice video. Thank you for making & posting it. ¿Do you think one can install a 14" bar on this Echo CS 3510 saw, kindly? (A dealer, and the Echo website indicates they sell no replacement bar/chain combo for this particular saw, other than the 16" length it's shipped with). Thank you. (My input: "Banshee").

[@RyanCookCarvin]

Yes, absolutely

[@Rmrstudio01]

Any cs 1/4 drum sproket work?

[@kevinpeterson298]

Has anyone come up with a part number for the 1/4 pitch sprocket for the 3510?

[@RyanCookCarvin]

Oregon has it

[@kevinpeterson298]

@@RyanCookCarvin part number please. Can pm me if you can"t put it out there. Thanks

[@NorCalSucculentShop]

Hi Ryan, what's the difference in the pro version saws? I would name that saw the "Little Ripper".

[@RyanCookCarvin]

like little more beefy, handle bars are metal and rubber .. little more well put together and more pricy in turn

[@johncress9813]

Call him Willie LOL

[@dennisbracci1504]

Bought a 3510 as you suggested. where can i get a carving bar .sproket and chain.

[@elliotbaxter5709]

@dennis bracci have you had any luck finding a 1/4" pitch sprocket?

[@dennisbracci1504]

@@elliotbaxter5709 found a sprocket. Looking for 12inch dime tip bar and chain to fit.

[@bryonyanjudahharry5057]

Hay do you have a part number for the sprocket

[@mattfleming86]

@@dennisbracci1504 If you have the PN for the sprocket that fits any chance you could share it?

[@jackthibodeau9048]

Which saws have compatible clutch drums with the 3510?

[@RyanCookCarvin]

not sure to be honest

[@MadMan_3353]

How does the saw run after changing the sprocket?

[@RyanCookCarvin]

Great exact same.

[@davonnlakey2725]

Woodie 👌

[@RyanCookCarvin]

thanks da

[@tonylawson8116]

Does this model have a 1/4 sprocket?

[@RyanCookCarvin]

yup a rim sprocket

[@TonkaShinn]

Hey Ryan, I am just a new carver currently using a Stihl MS170 with 16" 3/8 Stilh bar. I am looking for a 2nd saw to put a dime tip carving bar to get better details and I am digging this 3510. My challenge is I am pretty remote in Bella Coola BC... and I have searched and searched for a dealer near me and can't even find one in or near Williams Lake. Being a BC lad yourself, wondering if you have any words of wisdom for local dealers (well nothing is local to the Valley, but within reason) where I can get Echo Saws and Canon carving bars? And you've probably named it already but I think it should be called Mouse in honour of the cool shirt you were wearing when you got it.

[@RyanCookCarvin]

well maybe get a saw thats local so u can get it fixed easy .. but as for bars my website will be selling them soon but will take some time to get everything going

[@Danny-BamBam-Cason]

You could name it " Buzzy" buzz saw. 😀😎😂

[@RyanCookCarvin]

Thanks

[@ericenglund6668]

Don’t know what you named this saw but without ever seeing 1 I would name it Freddy (Kruger). Do you still feel the same way about this saw? I have a cs 310. BK was saying they don’t make a 1/4 pitch for that. So I’ll put a 16 bar on it and wait till I have some bucks. This saw for a starter? Or buy a 361P? Ty Eric

[@robertmckamie8397]

How about the echo partner

[@jasonannas8151]

As far as saw name let's go with butter

[@RyanCookCarvin]

good call

[@AnginNomad]

Hi Ryan. Greetings from Malaysia! Been following your channel and I’ve decided to try chainsaw carving during this ‘lockdown’. I can easily get Echo CS3000 in my area. I need to know if I can convert this into a carving saw. If so what do I need as a beginner? I need something for detailed works and another for all-rounder. Also I have to deal with a lot of tropical hardwood. Appreciate your time. Thanks!

[@RyanCookCarvin]

i think u can you mean the 3100? u just need Oregon sproket an then a carving bar

[@AnginNomad]

@@RyanCookCarvin we only have the 3000 here. You think it’s do-able?

[@elliotbaxter5709]

HELP haha. Has anyone been able to find a 1/4" sprocket for the 3510 anywhere? I've contacted 5 online saw parts stores and exhausted all options that I thought were possibilities. I've ordered two that did not fit so far...

[@RyanCookCarvin]

im also looking

[@elliotbaxter5709]

@@RyanCookCarvin Keep me posted brother! Thanks for all the knowledge you throw out there about carving. Much appreciated.

[@nich1067]

@@RyanCookCarvin Id love to convert it over to 1/4 as well. If anybody knows what drum/sprocket to use. Please post.

[@thomastucker3016]

Name clipper,or chipper

[@georgedavall9449]

Wow! No comment! 🙄

[@Shefton1]

The COVIDnator

[@georgedoganis6708]

I swear this guy looks like Will Farell

[@RyanCookCarvin]

Descendent of the great farrel. Lol jk but I wish

[@abeltoomowlawncarecompany8481]

Name Jack the Ripper

[@josefpavlik3127]

name for saw... ,,Sophie"

[@RyanCookCarvin]

Josef Pavlík good one. She is already a 501p lol love that thou

[@josefpavlik3127]

Ryan Cook Carves TV lol😂... btw nice video, as always😌👌