The Reximex Regime - Initial Thoughts

  Рет қаралды 10,320

Airgun Sniper-Elite

Airgun Sniper-Elite

Күн бұрын

Пікірлер: 61
@beybulatozden9508
@beybulatozden9508 2 жыл бұрын
Best wishes from Turkey ...hope everthing goes well about your health.
@davidcottom7750
@davidcottom7750 2 жыл бұрын
Nice one Mark, nice straight forward review and very thorough done in a easy to understand way, the features on that bullpup are many and are all the stuff you don't normally get and make your shooting experience all the better,i love the look of some of those other models they seem to be amazing value for money, when you look at what you get right off the bat it's incredible ATB Dave
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
Yes, some really nice rifles. The classic look of the Pretensis, to the regulated whistles and bells of the Ixia and Throne. The Throne is fully adjustable, but the Ixia is designed as a sub 12 ft/lbs model without the adjustable regulator unless you have FAC.
@LEE-ON-TOUR
@LEE-ON-TOUR 2 жыл бұрын
Always a very detailed review . All the best with your hospital visit , Hope to see ya on the flip-side !
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
Thanks Lee
@BionicRusty
@BionicRusty 2 жыл бұрын
All the best for Tuesday, Mark. Be good to here back from you in the next video. I was looking at an Ixia in my local RFD last week (there were a few there). Very tempted to try one because my new RM8 is spending more time at the shop than it is in the field.
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
I was toying with saving up a bit more for the Ixia. Here's a good review from big Dan's Airguns on one. kzbin.info/www/bejne/ronQc3x5oN-kjKM
@matthewshaw5792
@matthewshaw5792 Жыл бұрын
Enjoyed a honest review definitely gonna have a look
@JohnDoe-el5ir
@JohnDoe-el5ir 4 ай бұрын
One more thought, I got one that has normal manometer scale, evenly divided. I found out that I can charge it up over what it states , by measuring with more precise manometer. I end up on one red notch . Red notches start just over 250 bar. Green area is all the way up until 250 I didn’t get any shots stats.
@tony59able
@tony59able 2 жыл бұрын
Great video. I’m after a budget bullpup and was toying with a flash pup or Walther Reign but this is very interesting at the price. Thanks again great channel
@alanmullock381
@alanmullock381 2 жыл бұрын
Nice one Mark! Hope all goes well for you fella🤞🤞🤞🤞🤞👌👌👌👌👌😎
@malc1730
@malc1730 2 жыл бұрын
Best of luck for your opp look forward to the range test.
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
Thanks Malc. Looking forward to see how far I can push it at the range.
@garryadams67
@garryadams67 2 жыл бұрын
First things first Mark, all the best for next week, no rush to get the range work done your health is much more important. Nice review, yes finally a quality rifle to make the rip off manufacturers sit up a bit. I do like some of the other rifles in the range as well 👍anyway good luck and look forword to the next instalment. Cheers Garry.
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
Thanks Garry,. Yes, finally a new brand with some innovative ideas for those on a budget.
@simontanner
@simontanner 2 жыл бұрын
Great review look forward to seeing more 👍🏻
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
Shame the weather is shite at the moment, or I would be testing more pellets through it now.
@simontanner
@simontanner 2 жыл бұрын
@@airgunsniper-elite7385 hopefully won’t be long and hope you’re opp goes well 👍🏻
@markhomer5704
@markhomer5704 2 жыл бұрын
Best wishes from me and the Mrs for next week , superb review as usual , Reximex have certainly hit the ground running so to speak , especially with MYTH , thats one hell of a looker in my opinion . Two things have to be mentioned here ,, One , how many guns have you got now ?? Jeeezzzzz I thought I had a few .. that said , can you REALLY have too many ? And .... Two , I have a bet on with the mrs , that you have changed the cocking lever over to the left hand by the end of February . .. I know you want to ... what a way to get over an operation .. kinda therapeutic id say ...
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
Thanks Mark, Yes, another project in waiting. This will end up with a side lever that can be used on either side and a regulator by this time next year. First things first though. Remove that bloody snap off grub screw. It's not even a legal requirement to fit anti tamper, just an agreement with UK manufacturers and importers to pluck up good rifles for the end user. As far as how many guns I have, not quite sure. Three are in bits and in need of a over-hall, but lack of available parts, due to age are lacking. So there's probably another twelve to play with as far as rifles go. Like you say, never enough, but just have to keep the better half on side.
@jeffslade1892
@jeffslade1892 2 жыл бұрын
When Accupell don't work, try Accupell-FT or VMX-Pell - because they are quite different. They all come out of the H&N factory but different design.
@JohnDoe-el5ir
@JohnDoe-el5ir 4 ай бұрын
Mags are thinner I believe than Kral. At least for .177. What do you think about that rail level? It makes that unusable for some long mounts, so short ones preferred. I see in UK you get a better set: case and a cap, and also quick fill. On the last one I don’t know if it is an advantage. What it has also is a very textured front grip, I like it a lot.
@leedavison2129
@leedavison2129 2 жыл бұрын
Great review
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
Thanks Lee.
@Airgunfunrich
@Airgunfunrich 2 жыл бұрын
Another great video. Did think about getting one of those but decided on the Ixia, just got to justify the extra to the wife…. Hope your hospital bogies well 👍
@jeffslade1892
@jeffslade1892 2 жыл бұрын
You are right. It should be possible to take an airgun completely apart. Whether to service, repair, or modify it. It is not a toy. There should be no anti-tamper screws. The UK is far from the only country with restrictions. There is no need for this.
@ezrabrook3993
@ezrabrook3993 2 жыл бұрын
Good review 👍🏻🐴❤️🤠🇨🇱
@janetfrankish4058
@janetfrankish4058 2 жыл бұрын
Hi mate. It looks like it likes the heavy pellets. I'm a bit surprised about the barcuda lights. Atb Danny f. 😊
@dmaderosglass
@dmaderosglass 2 жыл бұрын
Hola....Cómo puedo aumentar los Jouls de fabrica q trae a un reximex apex??
@tonyashton780
@tonyashton780 2 жыл бұрын
You take care mucker and good luck.Its TURKISH! silk purse?/sows ear?
@PeteroHolmeso
@PeteroHolmeso Жыл бұрын
Hi I saw this the other day where you took the shroud off and there was a half inch unfortunately thread to put a silencer on and have a smaller gun. Unfortunately when I took the shroud of there was something like the inside of the Artrmis P15 . This has something similar, I just wondered if this comes out, as it would be ideal for me. Thank you Oete
@airgunsniper-elite7385
@airgunsniper-elite7385 Жыл бұрын
It should work if you have a threaded barrel. The reason I removed the shroud was because it wasn't quite wide enough to make a good sound suppressor, even with 7 baffles in it.
@PeteroHolmeso
@PeteroHolmeso Жыл бұрын
@@airgunsniper-elite7385 That is the oroblem where the screw thread should be there is just a round disc with a rubber washer around it. It has holes behind the rubber ring. I just realised it must come off or you would be unable to get the base of the shroud with the grub screw holding it on to the barrel. I think I will have another look. Thank you for getting back to me. Regards Petet
@PeteroHolmeso
@PeteroHolmeso Жыл бұрын
@@airgunsniper-elite7385 Hi Mark, I have had the shroud off again and this thing is as thick as the inside of the shroud. If you have an artemis around and take the shroud off that, you will see the baffles plus a thing that keeps the baffles in place. But unlike the Artemus the same piec must be made to stay. But sadly this does not surprise me, I have been trying to get the power dial to turn without any luck. I contacted the gunshop who told ne to the the cover of and there is a small grub screw just above the power dial I undid it and a ball bearing should gave fallen out but there wasn't one in there, so the power dial is stuck, I just hope the gunshop and rang right can come up with a solution. Thank you anyway, and keep up the great work. Peter
@airgunsniper-elite7385
@airgunsniper-elite7385 Жыл бұрын
@@PeteroHolmeso My chock was also stiff. It is normally down to the grub screw being too tight. I think its only about 1mm, but if you can unscrew it, then the choke adjuster should move. in both directions.
@PeteroHolmeso
@PeteroHolmeso Жыл бұрын
@@airgunsniper-elite7385 Hi Mark I have just had another look and realise I have cooked it up in the explanation. Where you screwed your silencer onto the 1/2 UNF thread at the end of the barrel. I don't have that just the short 1in tube with 4 holes in it and a flat top for the spring in the shroud to rest on when screwed in, and that is the thing I cannot move it has no grub screws, it will not twist or turn. I have pulled it pushed it and nothing. Unless they brought out a mark 1 and mark 2 with differences. Oh well thank you for the help it did make me look it over even more carefully. Thank you Pete
@srfsummers6261
@srfsummers6261 2 жыл бұрын
Seriously considering one of these, I like how it looks and the fact everything is covered and protected. I'm new to pcp and think I might have found the one. Good purchase for a newbie? Thanks for doing a good review.
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
Just make sure that you get a pull through cleaning kit, as all new rifles tend to have their barrels coated to protect them. This needs cleaning before you shoot it. Not every pellet shoots the same through every rifle. I have done some pellet tests to see what this rifle tends to like, so hopefully that will also help. You can buy sample packs of pellets, which work out cheaper to see what does work, and what doesn't.
@srfsummers6261
@srfsummers6261 2 жыл бұрын
@@airgunsniper-elite7385 Thanks for the advice, I've noticed a lot of reviews of different guns mention the need to clean the barrels. Been keeping up with your rapid fire tests.😊 Looks fun. My other choice is a Walther RM8 compact. What's your thoughts between the two for a newbie. I really just want something accurate, well made and reliable. Thanks again.👍
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
@@srfsummers6261 The RM8 compact is a tried and tested rifle that is really accurate, thanks to its Walther barrel, although I haven't fired one yet, I know people that have and are more than happy with them. They are also good value for money. I have considered this one myself. At the end of the day it depends on what you prefer, either bullpup or carbine.
@vinceyreay
@vinceyreay 5 ай бұрын
Does the Regime come with a bipod adaptor?
@airgunsniper-elite7385
@airgunsniper-elite7385 5 ай бұрын
@@vinceyreay No. I got one offline for QD stud bipod. They don't cost much.
@wrinkle1784
@wrinkle1784 2 жыл бұрын
It's in close competition with kral empire which is regulated and apex is not, do you recommend a regulated rifle (empire) over a non regulated( apex) one in general?
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
A regulator usually makes all the difference, unless the rifles have good working valves such as and Air Arms S200. I will be regulating my Reximex in due course. It should help with shot count and consistency overall.
@wrinkle1784
@wrinkle1784 2 жыл бұрын
Thank you and please do let us know the kind of regulator you would be using, I haven't found any specific regs for the regime yet. ✌
@yetiwheeler7972
@yetiwheeler7972 2 жыл бұрын
Can someone Please Test. an Alsekion!!!! Enjoyed the Review.
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
Would love to test one. I was hoping to get to this year's shooting show and approach some of the manufacturers and importers in regards to reviews. SMK are the importers. I will have to see what I can do this year.
@yetiwheeler7972
@yetiwheeler7972 2 жыл бұрын
@@airgunsniper-elite7385 it's a toss up between ATA OR Alsekion mx9.
@MJSherwood
@MJSherwood 2 жыл бұрын
I think Kral and reximex is a bit like Toyota and Lexus respectively
@nigelmonaireo5024
@nigelmonaireo5024 2 жыл бұрын
Can't put a moderator on it I don't think
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
You can fit one if you take off the shroud, but they should have made an adapter for the shroud. I unscrewed the shroud this morning and fitted a Webley QGS silencer directly onto the barrel. It has a 1/2 inch x 20 thread.
@bruceferguson1544
@bruceferguson1544 2 жыл бұрын
@@airgunsniper-elite7385 having received my Regime the middle of last month, it would appear the manufacturer or the importer/distributor has modified the barrel preventing the fixing of a moderator directly to the barrel by replacing the UNF thread with what can only be described as a crimped on flange. I couldn’t see any grub screws holding it on, nor could I make out if they had screwed the flange onto the thread before crimping it or removed the thread prior. With this adapted barrel I would add caution to the removal of the shroud, as the back end screws onto an adapter that is held in place by two very small grub screws that hold it to the barrel, if this comes loose, which mine did when I screwed the shroud back on means you then have to remove the cover to screw the adapter back in place. I’m no gun smith but my recommendation would be to remove the rifles cover prior to removing the shroud, as the adapter that the shroud screws onto is prevented from being removed by the flange and those grub screws are pitiful and likely to fail when you remove/replace the shroud.
@Zillawill
@Zillawill 2 жыл бұрын
I was all set on buying 1 of these with me being a left handed shooter, but fact I can't use 1 of the features because we live here in UK is just f'ing stupid
@thedeester100
@thedeester100 2 жыл бұрын
My first thoughts. That is an Ugly Rifle. It makes the Daystate Renegade look like a cute puppy. Each to their own taste I guess.
@wannabemgtow2540
@wannabemgtow2540 2 жыл бұрын
A Dremel is your friend when you have screwed up screw heads🔫
@williamking1554
@williamking1554 2 жыл бұрын
nice gun but it uses those crap magazines that always screw up
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
No problem with them yet. If they become an issue I will see what CARM magazines have.
@SNIPERSUPERTEN
@SNIPERSUPERTEN Жыл бұрын
Looks like a Luke Skywalker gun and sounds like a new variety of dog food.😭
@phillipsharpe6459
@phillipsharpe6459 2 жыл бұрын
Nice rifle, but a bit ugly, just my opinion, 😁👍
@airgunsniper-elite7385
@airgunsniper-elite7385 2 жыл бұрын
Yes, horses for courses Phil. Bullpups have always been marmite. I love it, and for accuracy and features out of the box you can't beat it for the price.
The Reximex Regime  -  Initial 30 yard range results
24:14
Airgun Sniper-Elite
Рет қаралды 2,8 М.
The Reximex Regime (PART TWO) 40 & 60 yard results
20:06
Airgun Sniper-Elite
Рет қаралды 1,5 М.
Beat Ronaldo, Win $1,000,000
22:45
MrBeast
Рет қаралды 144 МЛН
coco在求救? #小丑 #天使 #shorts
00:29
好人小丑
Рет қаралды 97 МЛН
Reximex Regime **FULL RACKNLOAD REVIEW**
17:08
RACKNLOAD
Рет қаралды 9 М.
Reximex Regime .177 review (UK Spec)-Big Dan's Airguns.
40:54
Big Dan's Airguns
Рет қаралды 20 М.
Reximex Accura. Affordable PCP full test and shoot
17:38
Airgun Extra
Рет қаралды 23 М.
Prison Because Of Your Airgun In England?
18:25
ThatGearGuy
Рет қаралды 212 М.
Is This Rifle The Ultimate Budget Powerhouse? Reximex Zone - Range and Country
28:00
Sorting out the faulty trigger on the Reximex Regime
22:21
Airgun Sniper-Elite
Рет қаралды 1,6 М.
APEX ( REGIME ) - Personalization & Accessories
2:38
Reximex
Рет қаралды 4,5 М.
Beat Ronaldo, Win $1,000,000
22:45
MrBeast
Рет қаралды 144 МЛН